When configured for interrupts (property "chardev" given), we receive
the shared memory from an ivshmem server. We do so asynchronously
after realize() completes, by setting up callbacks with
qemu_chr_add_handlers().
Keeping server I/O out of realize() that way avoids delays due to a
slow server. This is probably relevant only for hot plug.
However, this funny "no shared memory, yet" state of the device also
causes a raft of issues that are hard or impossible to work around:
* The guest is exposed to this state: when we enter and leave it its
shared memory contents is apruptly replaced, and device register
IVPosition changes.
This is a known issue. We document that guests should not access
the shared memory after device initialization until the IVPosition
register becomes non-negative.
For cold plug, the funny state is unlikely to be visible in
practice, because we normally receive the shared memory long before
the guest gets around to mess with the device.
For hot plug, the timing is tighter, but the relative slowness of
PCI device configuration has a good chance to hide the funny state.
In either case, guests complying with the documented procedure are
safe.
* Migration becomes racy.
If migration completes before the shared memory setup completes on
the source, shared memory contents is silently lost. Fortunately,
migration is rather unlikely to win this race.
If the shared memory's ramblock arrives at the destination before
shared memory setup completes, migration fails.
There is no known way for a management application to wait for
shared memory setup to complete.
All you can do is retry failed migration. You can improve your
chances by leaving more time between running the destination QEMU
and the migrate command.
To mitigate silent memory loss, you need to ensure the server
initializes shared memory exactly the same on source and
destination.
These issues are entirely undocumented so far.
I'd expect the server to be almost always fast enough to hide these
issues. But then rare catastrophic races are in a way the worst kind.
This is way more trouble than I'm willing to take from any device.
Kill the funny state by receiving shared memory synchronously in
realize(). If your hot plug hangs, go kill your ivshmem server.
For easier review, this commit only makes the receive synchronous, it
doesn't add the necessary error propagation. Without that, the funny
state persists. The next commit will do that, and kill it off for
real.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1458066895-20632-26-git-send-email-armbru@redhat.com>
close_peer_eventfds() cleans up three things: ioeventfd triggers if
they exist, eventfds, and the array to store them.
Commit 98609cd (v1.2.0) fixed it not to clean up ioeventfd triggers
when they don't exist (property ioeventfd=off, which is the default).
Unfortunately, the fix also made it skip cleanup of the eventfds and
the array then. This is a memory and file descriptor leak on unplug.
Additionally, the reset of nb_eventfds is skipped. Doesn't matter on
unplug. On peer disconnect, however, this permanently wedges the
interrupt vectors used for that peer's ID. The eventfds stay behind,
but aren't connected to a peer anymore. When the ID gets recycled for
a new peer, the new peer's eventfds get assigned to vectors after the
old ones. Commonly, the device's number of vectors matches the
server's, so the new ones get dropped with a "Too many eventfd
received" message. Interrupts either don't work (common case) or go
to the wrong vector.
Fix by narrowing the conditional to just the ioeventfd trigger
cleanup.
While there, move the "invalid" peer check to the only caller where it
can actually happen, and tighten it to reject own ID.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1458066895-20632-25-git-send-email-armbru@redhat.com>
ivshmem_read() processes server messages. These are 64 bit signed
integers. -1 is shared memory setup, 16 bit unsigned is a peer ID,
anything else is invalid.
ivshmem_read() rejects invalid negative messages right away, silently.
Invalid positive messages get rejected only in resize_peers(), and
ivshmem_read() then prints the rather cryptic message "failed to
resize peers array".
Extend the first check to cover all invalid messages, make it report
"server sent invalid message", and drop the second check.
Now resize_peers() can't fail anymore; simplify.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1458066895-20632-23-git-send-email-armbru@redhat.com>
An interrupt is set up when the interrupt's file descriptor is
received. Each message applies to the next interrupt vector.
Therefore, each vector cannot be set up more than once.
ivshmem_add_kvm_msi_virq() half-heartedly tries not to rely on this by
doing nothing then, but that's not going to recover from this error
should it become possible in the future. watch_vector_notifier()
doesn't even try.
Simply assert what is the case, so we get alerted if we ever screw it
up.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1458066895-20632-22-git-send-email-armbru@redhat.com>
The ivshmem device can either use MSI-X or legacy INTx for interrupts.
With MSI-X enabled, peer interrupt events trigger an MSI as they
should. But software can still raise INTx via interrupt status and
mask register in BAR 0. This is explicitly prohibited by PCI Local
Bus Specification Revision 3.0, section 6.8.3.3:
While enabled for MSI or MSI-X operation, a function is prohibited
from using its INTx# pin (if implemented) to request service (MSI,
MSI-X, and INTx# are mutually exclusive).
Fix the device model to leave INTx alone when using MSI-X.
Document that we claim to use INTx in config space even when we don't.
Unlike other devices, ivshmem does *not* use INTx when configured for
MSI-X and MSI-X isn't enabled by software.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1458066895-20632-21-git-send-email-armbru@redhat.com>
There are three predicates related to MSI-X:
* ivshmem_has_feature(s, IVSHMEM_MSI) is true unless the non-MSI-X
variant of the device is selected with msi=off.
* msix_present() is true when the device has the PCI capability MSI-X.
It's initially false, and becomes true during successful realize of
the MSI-X variant of the device. Thus, it's the same as
ivshmem_has_feature(s, IVSHMEM_MSI) for realized devices.
* msix_enabled() is true when msix_present() is true and guest software
has enabled MSI-X.
Code that differs between the non-MSI-X and the MSI-X variant of the
device needs to be guarded by ivshmem_has_feature(s, IVSHMEM_MSI) or
by msix_present(), except the latter works only for realized devices.
Code that depends on whether MSI-X is in use needs to be guarded with
msix_enabled().
Code review led me to two minor messes:
* ivshmem_vector_notify() calls msix_notify() even when
!msix_enabled(), unlike most other MSI-X-capable devices. As far as
I can tell, msix_notify() does nothing when !msix_enabled(). Add
the guard anyway.
* Most callers of ivshmem_use_msix() guard it with
ivshmem_has_feature(s, IVSHMEM_MSI). Not necessary, because
ivshmem_use_msix() does nothing when !msix_present(). That's
ivshmem's only use of msix_present(), though. Guard it
consistently, and drop the now redundant msix_present() check.
While there, rename ivshmem_use_msix() to ivshmem_msix_vector_use().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1458066895-20632-20-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
If pci_ivshmem_realize() fails after it created its migration blocker,
the blocker is left in place. Fix that by creating it last.
Likewise, if it fails after it called fifo8_create(), it leaks fifo
memory. Fix that the same way.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1458066895-20632-18-git-send-email-armbru@redhat.com>
We reuse errp after passing it host_memory_backend_get_memory(). If
both host_memory_backend_get_memory() and the reuse set an error, the
reuse will fail the assertion in error_setv(). Fortunately,
host_memory_backend_get_memory() can't fail.
Pass it &error_abort to make our assumption explicit, and to get the
assertion failure in the right place should it become invalid.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1458066895-20632-17-git-send-email-armbru@redhat.com>
Yes, the chardev is commonly useless after we read a bad version from
it, but destroying it is inappropriate anyway: the user created it, so
the user should be able to hold on to it as long as he likes. We
don't destroy it on other errors. Screwed up in commit 5105b1d.
Stop reading instead.
Also note QEMU's behavior in ivshmem-spec.txt.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1458066895-20632-16-git-send-email-armbru@redhat.com>
IVShmemState member eventfd_chr is useless since commit 9940c32. Drop
it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1458066895-20632-14-git-send-email-armbru@redhat.com>
USB Ehci emulation supports host controller capability registers.
But its mmio '.write' function was missing, which lead to a null
pointer dereference issue. Add a do nothing 'ehci_caps_write'
definition to avoid it; Do nothing because capability registers
are Read Only(RO).
Reported-by: Zuozhi Fzz <zuozhi.fzz@alibaba-inc.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1454072434-16045-1-git-send-email-ppandit@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
inotify_init1 usage was guarded by a check for linux but does not
exist on older distributions like CentOS 5 resulting in build
failures.
Signed-off-by: Matthew Fortune <matthew.fortune@imgtec.com>
Message-id: 6D39441BF12EF246A7ABCE6654B023536BB85D4A@hhmail02.hh.imgtec.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
All the callers for xhci_dma_write_u32s() are using mostly 5 * uint32_t
in len. To avoid unbound stack warning for the function, make it
statically allocated, and assert when it's not big enough in the
future.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-id: 1457661106-9569-1-git-send-email-peterx@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Mingw-w64 does not provide sys/ioctl.h and Linux builds don't need it,
so remove that include statement.
ERROR is defined by wingdi.h (included via windows.h). Undefine it before
it is redefined to avoid a compiler warning / error.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Message-id: 1458159439-32322-1-git-send-email-sw@weilnetz.de
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Simple unions were carrying a special case that hid their 'data'
QMP member from the resulting C struct, via the hack method
QAPISchemaObjectTypeVariant.simple_union_type(). But by using
the work we started by unboxing flat union and alternate
branches, coupled with the ability to visit the members of an
implicit type, we can now expose the simple union's implicit
type in qapi-types.h:
| struct q_obj_ImageInfoSpecificQCow2_wrapper {
| ImageInfoSpecificQCow2 *data;
| };
|
| struct q_obj_ImageInfoSpecificVmdk_wrapper {
| ImageInfoSpecificVmdk *data;
| };
...
| struct ImageInfoSpecific {
| ImageInfoSpecificKind type;
| union { /* union tag is @type */
| void *data;
|- ImageInfoSpecificQCow2 *qcow2;
|- ImageInfoSpecificVmdk *vmdk;
|+ q_obj_ImageInfoSpecificQCow2_wrapper qcow2;
|+ q_obj_ImageInfoSpecificVmdk_wrapper vmdk;
| } u;
| };
Doing this removes asymmetry between QAPI's QMP side and its
C side (both sides now expose 'data'), and means that the
treatment of a simple union as sugar for a flat union is now
equivalent in both languages (previously the two approaches used
a different layer of dereferencing, where the simple union could
be converted to a flat union with equivalent C layout but
different {} on the wire, or to an equivalent QMP wire form
but with different C representation). Using the implicit type
also lets us get rid of the simple_union_type() hack.
Of course, now all clients of simple unions have to adjust from
using su->u.member to using su->u.member.data; while this touches
a number of files in the tree, some earlier cleanup patches
helped minimize the change to the initialization of a temporary
variable rather than every single member access. The generated
qapi-visit.c code is also affected by the layout change:
|@@ -7393,10 +7393,10 @@ void visit_type_ImageInfoSpecific_member
| }
| switch (obj->type) {
| case IMAGE_INFO_SPECIFIC_KIND_QCOW2:
|- visit_type_ImageInfoSpecificQCow2(v, "data", &obj->u.qcow2, &err);
|+ visit_type_q_obj_ImageInfoSpecificQCow2_wrapper_members(v, &obj->u.qcow2, &err);
| break;
| case IMAGE_INFO_SPECIFIC_KIND_VMDK:
|- visit_type_ImageInfoSpecificVmdk(v, "data", &obj->u.vmdk, &err);
|+ visit_type_q_obj_ImageInfoSpecificVmdk_wrapper_members(v, &obj->u.vmdk, &err);
| break;
| default:
| abort();
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1458254921-17042-13-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Before this patch, blk_new() automatically assigned a name to the new
BlockBackend and considered it referenced by the monitor. This patch
removes the implicit monitor_add_blk() call from blk_new() (and
consequently the monitor_remove_blk() call from blk_delete(), too) and
thus blk_new() (and related functions) no longer take a BB name
argument.
In fact, there is only a single point where blk_new()/blk_new_open() is
called and the new BB is monitor-owned, and that is in blockdev_init().
Besides thus relieving us from having to invent names for all of the BBs
we use in qemu-img, this fixes a bug where qemu cannot create a new
image if there already is a monitor-owned BB named "image".
If a BB and its BDS tree are created in a single operation, as of this
patch the BDS tree will be created before the BB is given a name
(whereas it was the other way around before). This results in minor
change to the output of iotest 087, whose reference output is amended
accordingly.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The only remaining users of machine_init() only call
qemu_add_opts(). Rename machine_init() to opts_init() and move it
closer to the qemu_add_opts() calls on vl.c.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Change all machine_init() users that simply call type_register*()
to use type_init().
Cc: Evgeny Voevodin <e.voevodin@samsung.com>
Cc: Maksim Kozlov <m.kozlov@samsung.com>
Cc: Igor Mitsyanko <i.mitsyanko@gmail.com>
Cc: Dmitry Solodkiy <d.solodkiy@samsung.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: Michael Walle <michael@walle.cc>
Cc: "Hervé Poussineau" <hpoussin@reactos.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Leon Alrae <leon.alrae@imgtec.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The SD card object is not a SysBusDevice, so don't create it with
qdev_create() if we're not assigning it to a specific bus; use
object_new() instead.
This was causing 'info qtree' to segfault on boards with SD cards,
because qdev_create(NULL, TYPE_FOO) puts the created object on the
system bus, and then we may try to run functions like sysbus_dev_print()
on it, which fail when casting the object to SysBusDevice.
(This is the same mistake that we made with the NAND device
and fixed in commit 6749695eaaf346c1.)
Reported-by: xiaoqiang.zhao <zxq_yx_007@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: xiaoqiang.zhao <zxq_yx_007@163.com>
Message-id: 1458061009-7733-1-git-send-email-peter.maydell@linaro.org
At present, all DMA transfers complete inline (so a looping descriptor
queue will lock up the device). We also do not model pause/abort,
arbitrarion/priority, or debug features.
Signed-off-by: Grégory ESTRADE <gregory.estrade@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1457467526-8840-6-git-send-email-Andrew.Baumann@microsoft.com
[AB: implement 2D mode, cleanup/refactoring for upstream submission]
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The property channel driver now interfaces with the framebuffer device
to query and set framebuffer parameters. As a result of this, the "get
ARM RAM size" query now correctly returns the video RAM base address
(not total RAM size), and the ram-size property is no longer relevant
here.
Signed-off-by: Grégory ESTRADE <gregory.estrade@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1457467526-8840-5-git-send-email-Andrew.Baumann@microsoft.com
[AB: cleanup/refactoring for upstream submission]
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The framebuffer occupies the upper portion of memory (64MiB by
default), but it can only be controlled/configured via a system
mailbox or property channel (to be added by a subsequent patch).
Signed-off-by: Grégory ESTRADE <gregory.estrade@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1457467526-8840-4-git-send-email-Andrew.Baumann@microsoft.com
[AB: added Windows (BGR) support and cleanup/refactoring for upstream submission]
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At present only the core UART functions (data path for tx/rx) are
implemented, which is enough for UEFI to boot. The following
features/registers are unimplemented:
* Line/modem control
* Scratch register
* Extra control
* Baudrate
* SPI interfaces
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1457467526-8840-3-git-send-email-Andrew.Baumann@microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1457467526-8840-2-git-send-email-Andrew.Baumann@microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The new machine is a thin layer over the AST2400 ARM926-based SoC[1].
Between the minimal machine and the current SoC implementation there is
enough functionality to boot an aspeed_defconfig Linux kernel to
userspace. Nothing yet is specific to the Palmetto's BMC (other than
using an AST2400 SoC), but creating specific machine types is preferable
to a generic machine that doesn't match any particular hardware.
[1] http://www.aspeedtech.com/products.php?fPath=20&rId=376
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1458096317-25223-5-git-send-email-andrew@aj.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While the ASPEED AST2400 SoC[1] has a broad range of capabilities this
implementation is minimal, comprising an ARM926 processor, ASPEED VIC
and timer devices, and a 8250 UART.
[1] http://www.aspeedtech.com/products.php?fPath=20&rId=376
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1458096317-25223-4-git-send-email-andrew@aj.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement a basic ASPEED VIC device model for the AST2400 SoC[1], with
enough functionality to boot an aspeed_defconfig Linux kernel. The model
implements the 'new' (revised) register set: While the hardware exposes
both the new and legacy register sets, accesses to the model's legacy
register set will not be serviced (however the access will be logged).
[1] http://www.aspeedtech.com/products.php?fPath=20&rId=376
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1458096317-25223-3-git-send-email-andrew@aj.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement basic ASPEED timer functionality for the AST2400 SoC[1]: Up to
8 timers can independently be configured, enabled, reset and disabled.
Some hardware features are not implemented, namely clock value matching
and pulse generation, but the implementation is enough to boot the Linux
kernel configured with aspeed_defconfig.
[1] http://www.aspeedtech.com/products.php?fPath=20&rId=376
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1458096317-25223-2-git-send-email-andrew@aj.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
EPIT, GPT and other i.MX timers are using "abstract" clocks among which
a CLK_IPG_HIGH clock.
On i.MX25 and i.MX31 CLK_IPG and CLK_IPG_HIGH are mapped to the same clock
but on other SOC like i.MX6 they are mapped to distinct clocks.
This patch add the CLK_IPG_HIGH to prepare for SOC where these 2 clocks are
different.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 224bf650194760284cb40630e985867e1373276a.1456868959.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Most clocks supported by the CCM are useless to the qemu framework.
Only clocks related to timers (EPIT, GPT, PWM, WATCHDOG, ...) are usefull
to QEMU code.
Therefore this patch removes clock computation handling for all clocks but:
* CLK_NONE,
* CLK_IPG,
* CLK_32k
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 9e7222efb349801032e60c0f6b0fbad0e5dcf648.1456868959.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This way all CCM clock defines/enums are named CLK_XXX
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 8537df765c1713625c7a8b9aca4c7ca60b42e0c0.1456868959.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
GPT timer need to rollover when it reaches 0xffffffff.
It also need to reset to 0 when in "restart mode" and crossing the
compare 1 register.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 6e2b36117a249a78bf822dd59a390368f407136e.1456868959.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch moves the common class initialization code from
"virt-2.6" to the new abstract class. An empty property is added to
"virt-2.6" machine. In the meanwhile, related funtions are renamed
to "virt_2_6_*" for consistency.
Signed-off-by: Wei Huang <wei@redhat.com>
Message-id: 1457717778-17727-3-git-send-email-wei@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for future ARM virt machine types, this patch creates
an abstract type for all ARM machines. The current machine type in
QEMU (i.e. "virt") is renamed to "virt-2.6", whose naming scheme is
similar to other architectures. For the purpose of backward compatibility,
"virt" is converted to an alias, pointing to "virt-2.6". With this patch,
"qemu -M ?" lists the following virtual machine types along with others:
virt QEMU 2.6 ARM Virtual Machine (alias of virt-2.6)
virt-2.6 QEMU 2.6 ARM Virtual Machine
Signed-off-by: Wei Huang <wei@redhat.com>
Message-id: 1457717778-17727-2-git-send-email-wei@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Accumulated patches for target-ppc, pseries machine type and related
devices. As we are now in soft freeze, these are mostly fixes.
* Fix KVM migration for several SPRs that qemu didn't handle
* Clean up handling of SDR1, which allows a fix to the gdbstub
* Fix a race in spapr_rng
* Fix a bug with multifunction hotplug
The exception is the 7 patches to allow EEH on spapr-pci-host-bridge
devices (rather than the special and poorly designed
spapr-vfio-pci-host-bridge device). I believe these are low risk of
breaking non-EEH cases, and EEH cases were little used in practice
previously (since libvirt did not support the special device amongst
other things). It did have a draft posted before the soft freeze,
removes a very ugly VFIO interface, and removes device we'd like to
deprecate sooner rather than later. So, I'm hoping we can squeeze
these in during the soft freeze.
This includes two patches to the VFIO code, which Alex Williamson has
indicated he's ok with coming through my tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7P3U
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.6-20160316' into staging
ppc patch queue for 2016-03-16
Accumulated patches for target-ppc, pseries machine type and related
devices. As we are now in soft freeze, these are mostly fixes.
* Fix KVM migration for several SPRs that qemu didn't handle
* Clean up handling of SDR1, which allows a fix to the gdbstub
* Fix a race in spapr_rng
* Fix a bug with multifunction hotplug
The exception is the 7 patches to allow EEH on spapr-pci-host-bridge
devices (rather than the special and poorly designed
spapr-vfio-pci-host-bridge device). I believe these are low risk of
breaking non-EEH cases, and EEH cases were little used in practice
previously (since libvirt did not support the special device amongst
other things). It did have a draft posted before the soft freeze,
removes a very ugly VFIO interface, and removes device we'd like to
deprecate sooner rather than later. So, I'm hoping we can squeeze
these in during the soft freeze.
This includes two patches to the VFIO code, which Alex Williamson has
indicated he's ok with coming through my tree.
# gpg: Signature made Wed 16 Mar 2016 05:04:52 GMT using RSA key ID 20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.6-20160316:
vfio: Eliminate vfio_container_ioctl()
spapr_pci: Remove finish_realize hook
spapr_pci: (Mostly) remove spapr-pci-vfio-host-bridge
spapr_pci: Allow EEH on spapr-pci-host-bridge
spapr_pci: Eliminate class callbacks
spapr_pci: Switch to vfio_eeh_as_op() interface
vfio: Start improving VFIO/EEH interface
spapr_rng: fix race with main loop
target-ppc: Eliminate kvmppc_kern_htab global
target-ppc: Add helpers for updating a CPU's SDR1 and external HPT
target-ppc: Split out SREGS get/put functions
spapr_pci: fix multifunction hotplug
target-ppc: Add PVR for POWER8NVL processor
ppc: Add a few more P8 PMU SPRs
ppc: Fix migration of the TAR SPR
ppc: Define the PSPB register on POWER8
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
vfio_container_ioctl() was a bad interface that bypassed abstraction
boundaries, had semantics that sat uneasily with its name, and was unsafe
in many realistic circumstances. Now that spapr-pci-vfio-host-bridge has
been folded into spapr-pci-host-bridge, there are no more users, so remove
it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Now that spapr-pci-vfio-host-bridge is reduced to just a stub, there is
only one implementation of the finish_realize hook in sPAPRPHBClass. So,
we can fold that implementation into its (single) caller, and remove the
hook. That's the last thing left in sPAPRPHBClass, so that can go away as
well.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Now that the regular spapr-pci-host-bridge can handle EEH, there are only
two things that spapr-pci-vfio-host-bridge does differently:
1. automatically sizes its DMA window to match the host IOMMU
2. checks if the attached VFIO container is backed by the
VFIO_SPAPR_TCE_IOMMU type on the host
(1) is not particularly useful, since the default window used by the
regular host bridge will work with the host IOMMU configuration on all
current systems anyway.
Plus, automatically changing guest visible configuration (such as the DMA
window) based on host settings is generally a bad idea. It's not
definitively broken, since spapr-pci-vfio-host-bridge is only supposed to
support VFIO devices which can't be migrated anyway, but still.
(2) is not really useful, because if a guest tries to configure EEH on a
different host IOMMU, the first call will fail and that will be that.
It's possible there are scripts or tools out there which expect
spapr-pci-vfio-host-bridge, so we don't remove it entirely. This patch
reduces it to just a stub for backwards compatibility.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Now that the EEH code is independent of the special
spapr-vfio-pci-host-bridge device, we can allow it on all spapr PCI
host bridges instead. We do this by changing spapr_phb_eeh_available()
to be based on the vfio_eeh_as_ok() call instead of the host bridge class.
Because the value of vfio_eeh_as_ok() can change with devices being
hotplugged or unplugged, this can potentially lead to some strange edge
cases where the guest starts using EEH, then it starts failing because
of a change in status.
However, it's not really any worse than the current situation. Cases that
would have worked previously will still work (i.e. VFIO devices from at
most one VFIO IOMMU group per vPHB), it's just that it's no longer
necessary to use spapr-vfio-pci-host-bridge with the groupid pre-specified.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
The EEH operations in the spapr-vfio-pci-host-bridge no longer rely on the
special groupid field in sPAPRPHBVFIOState. So we can simplify, removing
the class specific callbacks with direct calls based on a simple
spapr_phb_eeh_enabled() helper. For now we implement that in terms of
a boolean in the class, but we'll continue to clean that up later.
On its own this is a rather strange way of doing things, but it's a useful
intermediate step to further cleanups.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
This switches all EEH on VFIO operations in spapr_pci_vfio.c from the
broken vfio_container_ioctl() interface to the new vfio_as_eeh_op()
interface.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
At present the code handling IBM's Enhanced Error Handling (EEH) interface
on VFIO devices operates by bypassing the usual VFIO logic with
vfio_container_ioctl(). That's a poorly designed interface with unclear
semantics about exactly what can be operated on.
In particular it operates on a single vfio container internally (hence the
name), but takes an address space and group id, from which it deduces the
container in a rather roundabout way. groupids are something that code
outside vfio shouldn't even be aware of.
This patch creates new interfaces for EEH operations. Internally we
have vfio_eeh_container_op() which takes a VFIOContainer object
directly. For external use we have vfio_eeh_as_ok() which determines
if an AddressSpace is usable for EEH (at present this means it has a
single container with exactly one group attached), and vfio_eeh_as_op()
which will perform an operation on an AddressSpace in the unambiguous case,
and otherwise returns an error.
This interface still isn't great, but it's enough of an improvement to
allow a number of cleanups in other places.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Since commit "60253ed1e6ec rng: add request queue support to rng-random",
the use of a spapr_rng device may hang vCPU threads.
The following path is taken without holding the lock to the main loop mutex:
h_random()
rng_backend_request_entropy()
rng_random_request_entropy()
qemu_set_fd_handler()
The consequence is that entropy_available() may be called before the vCPU
thread could even queue the request: depending on the scheduling, it may
happen that entropy_available() does not call random_recv()->qemu_sem_post().
The vCPU thread will then sleep forever in h_random()->qemu_sem_wait().
This could not happen before 60253ed1e6 because entropy_available() used
to call random_recv() unconditionally.
This patch ensures the lock is held to avoid the race.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@fr.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
fa48b43 "target-ppc: Remove hack for ppc_hash64_load_hpte*() with HV KVM"
purports to remove a hack in the handling of hash page tables (HPTs)
managed by KVM instead of qemu. However, it actually went in the wrong
direction.
That patch requires anything looking for an external HPT (that is one not
managed by the guest itself) to check both env->external_htab (for a qemu
managed HPT) and kvmppc_kern_htab (for a KVM managed HPT). That's a
problem because kvmppc_kern_htab is local to mmu-hash64.c, but some places
which need to check for an external HPT are outside that, such as
kvm_arch_get_registers(). The latter was subtly broken by the earlier
patch such that gdbstub can no longer access memory.
Basically a KVM managed HPT is much more like a qemu managed HPT than it is
like a guest managed HPT, so the original "hack" was actually on the right
track.
This partially reverts fa48b43, so we again mark a KVM managed external HPT
by putting a special but non-NULL value in env->external_htab. It then
goes further, using that marker to eliminate the kvmppc_kern_htab global
entirely. The ppc_hash64_set_external_hpt() helper function is extended
to set that marker if passed a NULL value (if you're setting an external
HPT, but don't have an actual HPT to set, the assumption is that it must
be a KVM managed HPT).
This also has some flow-on changes to the HPT access helpers, required by
the above changes.
Reported-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Tested-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
When a Power cpu with 64-bit hash MMU has it's hash page table (HPT)
pointer updated by a write to the SDR1 register we need to update some
derived variables. Likewise, when the cpu is configured for an external
HPT (one not in the guest memory space) some derived variables need to be
updated.
Currently the logic for this is (partially) duplicated in ppc_store_sdr1()
and in spapr_cpu_reset(). In future we're going to need it in some other
places, so make some common helpers for this update.
In addition the new ppc_hash64_set_external_hpt() helper also updates
SDR1 in KVM - it's not updated by the normal runtime KVM <-> qemu CPU
synchronization. In a sense this belongs logically in the
ppc_hash64_set_sdr1() helper, but that is called from
kvm_arch_get_registers() so can't itself call cpu_synchronize_state()
without infinite recursion. In practice this doesn't matter because
the only other caller is TCG specific.
Currently there aren't situations where updating SDR1 at runtime in KVM
matters, but there are going to be in future.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Since 3f1e147, QEMU has adopted a convention of supporting function
hotplug by deferring hotplug events until func 0 is hotplugged.
This is likely how management tools like libvirt would expose
such support going forward.
Since sPAPR guests rely on per-func events rather than
slot-based, our protocol has been to hotplug func 0 *first* to
avoid cases where devices appear within guests without func 0
present to avoid undefined behavior.
To remain compatible with new convention, defer hotplug in a
similar manner, but then generate events in 0-first order as we
did in the past. Once func 0 present, fail any attempts to plug
additional functions (as we do with PCIe).
For unplug, defer unplug operations in a similar manner, but
generate unplug events such that function 0 is removed last in guest.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The split IRQ chip mode via KVM_CAP_SPLIT_IRQCHIP was introduced with commit
15eafc2e60 but was broken for q35. This patch makes kernel_irqchip=split
functional for q35.
Signed-off-by: Rita Sinha <rita.sinha89@gmail.com>
Message-Id: <1457378525-16455-1-git-send-email-rita.sinha89@gmail.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
nvdimm work
sparse cpu id rework
ipmi enhancements
fixes all over the place
pxb option to tweak chassis number
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJW6B0mAAoJECgfDbjSjVRpCtMH/2xSrYsLGAM3tQZtcAlpoof/
LNjN0GxTMXWtbDfGLKQMkexAmrDtBOqXTNfPpDaeycvktcMJ4wUCqX8nWC+cNwl+
3Uu4yiR9J5qjB4ANRlHnW45aL9rq7Qv0BBMQvc0AxpKMqZ9sf4okd2a4ZprTbhHq
/q/JnWKa/a4CGAZrfwlonobtT/YvF+cbq6gQOxUWMaemptEZDhYaH8PMtw0Ituw1
HWsI5lkhy+bHC2FeoqKt+p3ypuIXfnbg1rJyAiyVzgwz4289aMoh6nBll6WFRGpI
vEligkFv4GBjNlYloUaGLlJxz3RE/7uPGER2lSH0OYTSVNc1zUbvbmv/7DIucSA=
=0EjS
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
vhost, virtio, pci, pc, acpi
nvdimm work
sparse cpu id rework
ipmi enhancements
fixes all over the place
pxb option to tweak chassis number
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 15 Mar 2016 14:33:10 GMT using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream: (51 commits)
hw/acpi: fix GSI links UID
ipmi: add some local variables in ipmi_sdr_init
ipmi: remove the need of an ending record in the SDR table
ipmi: use a function to initialize the SDR table
ipmi: add a realize function to the device class
ipmi: add rsp_buffer_set_error() helper
ipmi: remove IPMI_CHECK_RESERVATION() macro
ipmi: replace IPMI_ADD_RSP_DATA() macro with inline helpers
ipmi: remove IPMI_CHECK_CMD_LEN() macro
MAINTAINERS: machine core
MAINTAINERS: Add an entry for virtio header files
pc: acpi: clarify why possible LAPIC entries must be present in MADT
pc: acpi: drop cpu->found_cpus bitmap
pc: acpi: create Processor and Notify objects only for valid lapics
pc: acpi: create MADT.lapic entries only for valid lapics
pc: acpi: SRAT: create only valid processor lapic entries
pc: acpi: cleanup qdev_get_machine() calls
machine: introduce MachineClass.possible_cpu_arch_ids() hook
pc: init pcms->apic_id_limit once and use it throughout pc.c
pc: acpi: remove NOP assignment
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
According to the ACPI spec, each UID must be unique.
Use the irq number as UID for GSI links.
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch adds a couple of variables to manipulate the raw sdr
entries. The const attribute is also removed on init_sdrs. This will
ease the introduction of a sdr loader using a file.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently, the code initializing the sdr table relies on an ending
record with a recid of 0xffff. This patch changes the loop to use the
sdr size as a breaking condition.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch moves the code section initializing the sdrs in its own
routine to prepare ground for changes in the subsequent patches.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This will be useful to define and use properties when the object is
instantiated.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The third byte in the response buffer of an IPMI command holds the
error code. In many IPMI command handlers, this byte is updated
directly. This patch adds a helper routine to clarify why this byte is
being used.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Some IPMI command handlers in the BMC simulator use a macro
IPMI_CHECK_RESERVATION() to check a SDR reservation but the macro
implicitly uses local variables. This patch simply removes it.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The IPMI command handlers in the BMC simulator use a macro
IPMI_ADD_RSP_DATA() to push bytes in a response buffer. The macro
hides the fact that it implicitly uses variables local to the handler,
which is misleading.
This patch introduces a simple 'struct RspBuffer' and inlined helper
routines to store byte(s) in a response buffer. rsp_buffer_push()
replaces the macro IPMI_ADD_RSP_DATA() and rsp_buffer_pushmore() is
new helper to push multiple bytes. The latest is used in the command
handlers get_msg() and get_sdr() which are manipulating the buffer
directly.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Most IPMI command handlers in the BMC simulator start with a call to
the macro IPMI_CHECK_CMD_LEN() which verifies that a minimal number of
arguments expected by the command are indeed available. To achieve
this task, the macro implicitly uses local variables which is
misleading in the code.
This patch adds a 'cmd_len_min' attribute to the struct IPMICmdHandler
defining the minimal number of arguments expected by the command and
moves this check in the global command handler ipmi_sim_handle_command().
To clarify the checks being done on the received command, the patch
introduces a helper ipmi_get_handler().
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
cpu->found_cpus bitmap is used for setting present
flag in CPON AML package. But it takes a bunch of code
to fill bitmap and could be simplified by getting
presense info from possible CPUs list directly.
So drop cpu->found_cpus bitmap and unroll possible
CPUs list into APIC index array at the place where
CPUON AML package is created.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
do not assume that all lapics in range 0..apic_id_limit
are valid and do not create Processor and Notify objects
for not possible lapics.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
do not assume that all lapics in range 0..apic_id_limit
are valid and do not create lapic entries for not
possible lapics in MADT.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
When APIC IDs are sparse*, in addition to valid LAPIC
entries the SRAT is also filled invalid ones for non
possible APIC IDs.
Fix it by asking machine for all possible APIC IDs
instead of wrongly assuming that all APIC IDs in
range 0..apic_id_limit are possible.
* sparse lapic topology CLI:
-smp x,sockets=2,cores=3,maxcpus=6
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
cache qdev_get_machine() result in acpi_setup/acpi_build_update
time and pass it as an argument to child functions that need it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
on x86 currently range 0..max_cpus is used to generate
architecture-dependent CPU ID (APIC Id) for each present
and possible CPUs. However architecture-dependent CPU IDs
list could be sparse and code that needs to enumerate
all IDs (ACPI) ended up doing guess work enumerating all
possible and impossible IDs up to
apic_id_limit = x86_cpu_apic_id_from_index(max_cpus).
That leads to creation of MADT entries and Processor
objects in ACPI tables for not possible CPUs.
Fix it by allowing board specify a concrete list of
CPU IDs accourding its own rules (which for x86 depends
on topology). So that code that needs this list could
request it from board instead of trying to guess
what IDs are correct on its own.
This interface will also allow to help making AML
part of CPU hotplug target independent so it could
be reused for ARM target.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Emulate dsm method after IO VM-exit
Currently, we only introduce the framework and no function is actually
supported
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If dsm memory is successfully patched, we let qemu fully emulate
the dsm method
This patch saves _DSM input parameters into dsm memory, tell dsm
memory address to QEMU, then fetch the result from the dsm memory
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The dsm memory is used to save the input parameters and store
the dsm result which is filled by QEMU.
The address of dsm memory is decided by bios and patched into
int32 object named "MEMA"
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
32 bits IO port starting from 0x0a18 in guest is reserved for NVDIMM
ACPI emulation. The table, NVDIMM_DSM_MEM_FILE, will be patched into
NVDIMM ACPI binary code
OSPM uses this port to tell QEMU the final address of the DSM memory
and notify QEMU to emulate the DSM method
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Legacy Windows operating systems like Windows XP and Windows 2003
require _DIS method to be present for all interrupt links.
PC machines already have a no-op implemented for GSI links, add
it also in Q35.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
change some "rbca" to "rcrb"(root complex register block) while
the other to "rcba"(root complex base address).
Bonus: add more comments and fix some indentation.
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Actually fixes linux not finding virtio 1.0 device virtqueues after
reboot. Which is new I think, any chance linux kernel virtio code
became more strict in 4.3?
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Tested-by: Fam Zheng <famz@redhat.com>
On x86-based systems Linux determines the presence and the type of
floppy drives via a query of a CMOS field. So does SeaBIOS when
populating the return data for int 0x13 function 0x08.
However Windows doesn't do it. Instead, it requests this information
from BIOS via int 0x13/0x08 or through ACPI objects _FDE (Floppy Drive
Enumerate) and _FDI (Floppy Drive Information) of the floppy controller
object. On UEFI systems only ACPI-based detection is supported.
QEMU doesn't provide those objects in its ACPI tables and as a result
floppy drives are invisible to Windows on UEFI/OVMF.
This patch adds those objects to the floppy controller in DSDT,
populating them with the information from respective QEMU objects.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: John Snow <jsnow@redhat.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Kevin O'Connor <kevin@koconnor.net>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When populating ACPI objects for floppy drives one needs to provide the
maximum values for cylinder, sector, and head number the drive supports.
This patch adds a function that iterates through the array of predefined
floppy drive formats and returns the maximum values of c, h, s, out of
those matching the given floppy drive type.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: John Snow <jsnow@redhat.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Kevin O'Connor <kevin@koconnor.net>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Make it possible to query the CMOS type of a floppy drive outside of the
source file where it's defined.
It will allow to properly populate the corresponding ACPI objects and
thus enable Windows on BIOS-less systems to access the floppy drives.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: John Snow <jsnow@redhat.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Kevin O'Connor <kevin@koconnor.net>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Instead of statically declaring the floppy controller in DSDT, with its
_STA method depending on some obscure bit in the parent ISA bridge, add
the object dynamically to DSDT via AML API only when the controller is
present.
The _STA method is no longer necessary and is therefore dropped. So are
the declarations of the fields indicating whether the contoller is
enabled.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: John Snow <jsnow@redhat.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Kevin O'Connor <kevin@koconnor.net>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If host_memory_backend_get_memory() were to return error and
NULL MemoryRegion, pc_dimm_check_memdev_is_busy() would crash
dereferencing NULL pointer in memory_region_is_mapped().
But if error is set and non NULL MemoryRegion is returned
then error_setg() will fail with "error already set" assertion
in error_setv()
To avoid above issues use typical error handling pattern
for property setters:
Error *local_error = NULL;
...
error_propagate(errp, local_err);
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The patch for the kernel part is in linux-next already:
commit ac88e7c908b920866e529862f2b2f0129b254ab2
Author: Igor Redko <redkoi@virtuozzo.com>
Date: Thu Feb 18 09:23:01 2016 +1100
virtio_balloon: export 'available' memory to balloon statistics
Add a new field, VIRTIO_BALLOON_S_AVAIL, to virtio_balloon memory
statistics protocol, corresponding to 'Available' in /proc/meminfo.
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Igor Redko <redkoi@virtuozzo.com>
CC: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Minimizes the possibility to assign
the same bit to different features.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Commits 1811e64c and a6df8adf use the same virtio feature bit 4
for different features.
Fix it by using different bits.
Reported-by: Laurent Vivier <lvivier@redhat.com>
Tested-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
The segfault here is triggered by the driver notifying the stats queue
twice after adding a buffer to it. This effectively resets stats_vq_elem
back to NULL and QEMU crashes on the next stats timer tick in
balloon_stats_poll_cb.
This is a regression introduced in 51b19ebe43, although admittedly
the device assumed too much about the stats queue protocol even before
that commit. This commit adds a few more checks and ensures that the one
stats buffer gets deallocated on device reset.
Cc: qemu-stable@nongnu.org
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This is a very limited form of support for runtime patching -
similar in functionality to what we can do with ACPI_EXTRACT
macros in python, but implemented in C.
This is to allow ACPI code direct access to data tables -
which is exactly what DataTableRegion is there for, except
no known windows release so far implements DataTableRegion.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Extend aml_operation_region() to use object as offset
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It will be used by nvdimm acpi
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It will be used by nvdimm acpi
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Devices like Intel graphics are known to not only have bad checksums,
but also the wrong device ID. This is not so surprising given that
the video BIOS is typically part of the system firmware image rather
that embedded into the device and needs to support any IGD device
installed into the system.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Match common vfio code with setup, exit, and finalize functions for
BAR, quirk, and VGA management. VGA is also changed to dynamic
allocation to match the other MemoryRegions.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Both platform and PCI vfio drivers create a "slow", I/O memory region
with one or more mmap memory regions overlayed when supported by the
device. Generalize this to a set of common helpers in the core that
pulls the region info from vfio, fills the region data, configures
slow mapping, and adds helpers for comleting the mmap, enable/disable,
and teardown. This can be immediately used by the PCI MSI-X code,
which needs to mmap around the MSI-X vector table.
This also changes VFIORegion.mem to be dynamically allocated because
otherwise we don't know how the caller has allocated VFIORegion and
therefore don't know whether to unreference it to destroy the
MemoryRegion or not.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In preparation for supporting capability chains on regions, wrap
ioctl(VFIO_DEVICE_GET_REGION_INFO) so we don't duplicate the code for
each caller.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
vfio-pci currently requires a host= parameter, which comes in the
form of a PCI address in [domain:]<bus:slot.function> notation. We
expect to find a matching entry in sysfs for that under
/sys/bus/pci/devices/. vfio-platform takes a similar approach, but
defines the host= parameter to be a string, which can be matched
directly under /sys/bus/platform/devices/. On the PCI side, we have
some interest in using vfio to expose vGPU devices. These are not
actual discrete PCI devices, so they don't have a compatible host PCI
bus address or a device link where QEMU wants to look for it. There's
also really no requirement that vfio can only be used to expose
physical devices, a new vfio bus and iommu driver could expose a
completely emulated device. To fit within the vfio framework, it
would need a kernel struct device and associated IOMMU group, but
those are easy constraints to manage.
To support such devices, which would include vGPUs, that honor the
VFIO PCI programming API, but are not necessarily backed by a unique
PCI address, add support for specifying any device in sysfs. The
vfio API already has support for probing the device type to ensure
compatibility with either vfio-pci or vfio-platform.
With this, a vfio-pci device could either be specified as:
-device vfio-pci,host=02:00.0
or
-device vfio-pci,sysfsdev=/sys/devices/pci0000:00/0000:00:1c.0/0000:02:00.0
or even
-device vfio-pci,sysfsdev=/sys/bus/pci/devices/0000:02:00.0
When vGPU support comes along, this might look something more like:
-device vfio-pci,sysfsdev=/sys/devices/virtual/intel-vgpu/vgpu0@0000:00:02.0
NB - This is only a made up example path
The same change is made for vfio-platform, specifying sysfsdev has
precedence over the old host option.
Tested-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Let's use g_new0 to allocate cpu_states.
Suggested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
As we now have the new machine definitions, that let us disable/enable
machine options more easily, we need a way to save them and make them
publicly available.
The new s390-virtio-ccw.h header exports the s390 ccw machine state
and class, so they can be easily used in other C files.
Signed-off-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Most of the machine definition code looks the same between different
machine versions. The new DEFINE_CCW_MACHINE macro makes defining a
new machine easier by inserting standard machine version
definitions. This also makes it possible to propagate values between
machine versions.
The patch is inspired by code from hw/ppc/spapr.c
Signed-off-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Implement cpu hotplug routine and add the machine hook.
Signed-off-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Message-Id: <1457112875-5209-8-git-send-email-mjrosato@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Check for and propogate errors during s390 cpu creation.
Signed-off-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Message-Id: <1457112875-5209-7-git-send-email-mjrosato@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Link each CPUState as property machine/cpu[n] during initialization.
Add a hotplug handler to s390-virtio-ccw machine and set the
state during plug.
Signed-off-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Message-Id: <1457112875-5209-6-git-send-email-mjrosato@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Once hotplug is enabled, interrupts may come in for CPUs
with an address > smp_cpus. Allocate for this and allow
search routines to look beyond smp_cpus.
Signed-off-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Message-Id: <1457112875-5209-5-git-send-email-mjrosato@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Both initial and hotplugged CPUs need to set the same initial
state.
Signed-off-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Message-Id: <1457112875-5209-3-git-send-email-mjrosato@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Ensure a valid cpu_model is set upfront by setting the
default value directly into the MachineState when none is
specified. This is needed to ensure hotplugged CPUs share
the same cpu_model.
Signed-off-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Message-Id: <1457112875-5209-2-git-send-email-mjrosato@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Add a fw_cfg device node to the ACPI DSDT. This is mostly
informational, as the authoritative fw_cfg MMIO region(s)
are listed in the Device Tree. However, since we are building
ACPI tables, we might as well be thorough while at it...
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Marc Marí <markmb@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1455906029-25565-5-git-send-email-somlo@cmu.edu
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add a fw_cfg device node to the ACPI DSDT. While the guest-side
firmware can't utilize this information (since it has to access
the hard-coded fw_cfg device to extract ACPI tables to begin with),
having fw_cfg listed in ACPI will help the guest kernel keep a more
accurate inventory of in-use IO port regions.
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Marc Marí <markmb@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1455906029-25565-4-git-send-email-somlo@cmu.edu
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Move BIOS_CFG_IOPORT define from pc.c to pc.h, and rename
it to FW_CFG_IO_BASE.
Cc: Marc Marí <markmb@redhat.com>
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Marc Marí <markmb@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1455906029-25565-3-git-send-email-somlo@cmu.edu
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Expose the size of the control register (FW_CFG_CTL_SIZE) in fw_cfg.h.
Add comment to fw_cfg_io_realize() pointing out that since the
8-bit data register is always subsumed by the 16-bit control
register in the port I/O case, we use the control register width
as the *total* width of the (classic, non-DMA) port I/O region reserved
for the device.
Cc: Marc Marí <markmb@redhat.com>
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Marc Marí <markmb@redhat.com>
Message-id: 1455906029-25565-2-git-send-email-somlo@cmu.edu
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add property to specify rocker world. All ports will be assigned to this
world.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Until now, 0 is returned in this error case. Fix it ro return -ENOMEM.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Port to world assignment should be permitted only by qemu user. Driver
should not be able to do it, so forbid that possibility.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Ne2000 NIC uses ring buffer of NE2000_MEM_SIZE(49152)
bytes to process network packets. Registers PSTART & PSTOP
define ring buffer size & location. Setting these registers
to invalid values could lead to infinite loop or OOB r/w
access issues. Add check to avoid it.
Reported-by: Yang Hongke <yanghongke@huawei.com>
Tested-by: Yang Hongke <yanghongke@huawei.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Remove the RECOVER_BUFFERED_DATA command from the list of commands that
are handled by scsi_req_xfer(). Given that this command is
tape-specific, it should be handled only by scsi_stream_req_xfer().
Signed-off-by: Alex Pyrgiotis <apyrgio@arrikto.com>
Message-Id: <1457365822-22435-1-git-send-email-apyrgio@arrikto.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
All references to mr->ram_addr are replaced by
memory_region_get_ram_addr(mr) (except for a few assertions that are
replaced with mr->ram_block).
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <1456813104-25902-5-git-send-email-famz@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When a DMA transfer is done (ie all bytes have been transfered), the corresponding
Terminal Count bit must be set in the status register.
This bit is already cleared in i8257_read_cont and i8257_write_cont when required.
This fixes (at least) floppy transfer in IBM 40p firmware, which checks in DMA
controller if everything went fine.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <1456404332-31556-1-git-send-email-hpoussin@reactos.org>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
An upcoming patch will alter how simple unions, like InputEvent, are
laid out, which will impact all lines of the form 'evt->u.XXX'
(expanding it to the longer 'evt->u.XXX.data'). For better
legibility in that patch, and less need for line wrapping, it's better
to use a temporary variable to reduce the effect of a layout change to
just the variable initializations, rather than every reference within
an InputEvent.
There was one instance in hid.c:hid_pointer_event() where the code
was referring to evt->u.rel inside the case label where evt->u.abs
is the correct name; thankfully, both members of the union have the
same type, so it happened to work, but it is now cleaner.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1457021813-10704-8-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
No need to roll our own use of the dealloc visitors when we can
just directly use the qapi_free_FOO() functions that do what we
want in one line.
In net.c, inline net_visit() into its remaining lone caller.
After this patch, test-visitor-serialization.c is the only
non-generated file that needs to use a dealloc visitor, because
it is testing low level aspects of the visitor interface.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1456262075-3311-2-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The GICv2 introduces a new CPU interface register GICC_DIR, which
allows an OS to split the "priority drop" and "deactivate interrupt"
parts of interrupt completion. Implement this register.
(Note that the register is at offset 0x1000 in the CPU interface,
which means it is on a different 4K page from all the other registers.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Sergey Fedorov <serge.fdrv@gmail.com>
Message-id: 1456854176-7813-1-git-send-email-peter.maydell@linaro.org
Support ARM big-endian ELF files in system-mode emulation. When loading
an elf, determine the endianness mode expected by the elf, and set the
relevant CPU state accordingly.
With this, big-endian modes are now fully supported via system-mode LE,
so there is no need to restrict the elf loading to the TARGET
endianness so the ifdeffery on TARGET_WORDS_BIGENDIAN goes away.
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: fix typo in comments]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some CPUs are of an opposite data-endianness to other components in the
system. Sometimes elfs have the data sections layed out with this CPU
data-endianness accounting for when loaded via the CPU, so byte swaps
(relative to other system components) will occur.
The leading example, is ARM's BE32 mode, which is is basically LE with
address manipulation on half-word and byte accesses to access the
hw/byte reversed address. This means that word data is invariant
across LE and BE32. This also means that instructions are still LE.
The expectation is that the elf will be loaded via the CPU in this
endianness scheme, which means the data in the elf is reversed at
compile time.
As QEMU loads via the system memory directly, rather than the CPU, we
need a mechanism to reverse elf data endianness to implement this
possibility.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add an API to load an elf header header from a file. Populates a
buffer with the header contents, as well as a boolean for whether the
elf is 64b or not. Both arguments are optional.
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: Fix typo in comment]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
PMM pointed out that ldl_phys and stl_phys are dependent on the CPU's
endianness, whereas device model code should be independent of
it. This changes the relevant Raspberry Pi devices to explicitly call
the little-endian variants.
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1456880233-22568-1-git-send-email-Andrew.Baumann@microsoft.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the user passes us an EL3 boot rom, then it is going to want to
implement the PSCI interface itself. In this case, disable QEMU's
internal PSCI implementation so it does not get in the way, and
instead start all CPUs in an SMP configuration at once (the boot
rom will catch them all and pen up the secondaries until needed).
The boot rom code is also responsible for editing the device tree
to include any necessary information about its own PSCI implementation
before eventually passing it to a NonSecure guest.
(This "start all CPUs at once" approach is what both ARM Trusted
Firmware and UEFI expect, since it is what the ARM Foundation Model
does; the other approach would be to provide some emulated hardware
for "start the secondaries" but this is simplest.)
This is a compatibility break, but I don't believe that anybody
was using a secure boot ROM with an SMP configuration. Such a setup
would be somewhat broken since there was nothing preventing nonsecure
guest code from calling the QEMU PSCI function to start up a secondary
core in a way that completely bypassed the secure world.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 1456853976-7592-1-git-send-email-peter.maydell@linaro.org
If the virt board is started with the 'secure' property set to
request a Secure setup, then make the first flash device be
visible only to the Secure world.
This is a breaking change, but I don't expect it to be noticed
by anybody, because running TZ-aware guests isn't common and
those guests are generally going to be booting from the flash
and implicitly expecting their Non-secure guests to not touch it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1455288361-30117-5-git-send-email-peter.maydell@linaro.org
If we're loading a BIOS image into the first flash device,
load it into the flash's memory region specifically, not
into the physical address where the flash resides. This will
make a difference when the flash might be in the Secure
address space rather than the Nonsecure one.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1455288361-30117-4-git-send-email-peter.maydell@linaro.org
Add a new function load_image_mr(), which behaves like
load_image_targphys() except that it loads the ROM image to
a specified MemoryRegion rather than to a specified physical
address. This is useful when a ROM blob needs to be loaded
to a particular flash or ROM device but the address of that
device in the machine's address space is not known. (For
instance, ROMs in devices, or ROMs which might exist in
a different address space to the system address space.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1455288361-30117-3-git-send-email-peter.maydell@linaro.org
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
If we're booting in Secure mode, provide a secure-only RAM
(just 16MB) so that secure firmware has somewhere to run
from that won't be accessible to the Non-secure guest.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1455288361-30117-2-git-send-email-peter.maydell@linaro.org
The sdhci device was missing a DeviceClass reset method;
implement it. Poweron reset looks the same as reset commanded
by the guest via the device registers, apart from modelling of
the rpi 'pending insert interrupt on powerup' quirk.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1456493044-10025-3-git-send-email-peter.maydell@linaro.org
The sd.c SD card emulation code can be in a state where the
SDState BlockBackend pointer is NULL; this is treated as
"card not present". Add a missing check to sd_get_inserted()
so that we don't segfault in this situation.
(This could be provoked by the guest writing to the SDHCI
register to do a reset on a xilinx-zynq-a9 board; it will
also happen at startup when sdhci implements its DeviceClass
reset method.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1456493044-10025-2-git-send-email-peter.maydell@linaro.org
The virt board restricts guests to only 30GB of RAM. This is a
hangover from the vexpress-a15 board, and there's no inherent reason
for it. 30GB is smaller than you might reasonably want to provision
a VM for on a beefy server machine. Raise the limit to 255GB.
We choose 255GB because the available space we currently have
below the 1TB boundary is up to the 512GB mark, but we don't
want to paint ourselves into a corner by assigning it all to
RAM. So we make half of it available for RAM, with the 256GB..512GB
range available for future non-RAM expansion purposes.
If we need to provide more RAM to VMs in the future then we need to:
* allocate a second bank of RAM starting at 2TB and working up
* fix the DT and ACPI table generation code in QEMU to correctly
report two split lumps of RAM to the guest
* fix KVM in the host kernel to allow guests with >40 bit address spaces
The last of these is obviously the trickiest, but it seems
reasonable to assume that anybody configuring a VM with a quarter
of a terabyte of RAM will be doing it on a host with more than a
terabyte of physical address space.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Tested-by: Wei Huang <wei@redhat.com>
Message-id: 1456402182-11651-1-git-send-email-peter.maydell@linaro.org
This commit effectively reverts:
commit 4621c1768e
Author: Amit Shah <amit.shah@redhat.com>
Date: Wed Nov 21 11:21:19 2012 +0530
virtio-rng: remove extra request for entropy
but instead of calling virtio_rng_process unconditionally, it
first checks to see if the queue is empty as a little bit of
optimization.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Message-Id: <1456998514-19271-1-git-send-email-lprosek@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
We must not allow a channel program to suspend if the suspend
control bit in the orb had not been specified.
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Even PCI_CAP_FLAGS has the same value as PCI_MSIX_FLAGS, the later one is
the more proper on retrieving MSIX entries.
This patch uses PCI_MSIX_FLAGS to retrieve the MSIX entries.
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
CC: Cornelia Huck <cornelia.huck@de.ibm.com>
CC: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <1455895091-7589-3-git-send-email-richard.weiyang@gmail.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
machine_init() will be gone, but we don't need it if we just
initialize the channel_subsys fields statically.
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Alexander Graf <agraf@suse.de>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1455656347-29033-4-git-send-email-ehabkost@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
[adapted on top of indicator changes]
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
There's no need to use g_malloc0() to allocate the channel_subsys
struct, just use a static variable.
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Alexander Graf <agraf@suse.de>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1455656347-29033-3-git-send-email-ehabkost@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
[adapted on top of indicator changes]
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Indicator refcounting interfaces are introduced. This patch fixes
introducing unneeded indicator mappings and failure to release
AISB mappings on deregistration.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Currently, virtio-ccw uses its own interfaces to keep indicators mapped
just once even if the same address has been registered multiple times.
These interfaces fit the PCI use case as well. Therefore, move them to
css and make them generic interfaces.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
When configured to inject an NMI, watchdog_perform_action() may cause
the BQL to be temporarily relinquished (inject_nmi() → ... →
s390_nmi() → s390_cpu_restart() → run_on_cpu()). When the guest issues
diag 288 again in response to the NMI, the diag 288 operation will
race against wdt_diag288_reset(). Depending on scheduler behaviour,
wdt_diag288_reset() may be run after the guest issued a diag 288
Init. As a result, we will cancel the timer the guest just set up. The
effect observed by the guest is that a second expiry does not trigger
the watchdog action and diag 288 Change operations fail.
Fix this by resetting the timer _before_ invoking the action.
Signed-off-by: Sascha Silbe <silbe@linux.vnet.ibm.com>
Acked-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
All lowercase, use-dash instead of CamelCase.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
The "max" value is being compared with >=, but addr + width points to
the first byte that will _not_ be copied. Laszlo suggested using a
"greater than" comparison, instead of subtracting one like it is
already done above for the height, so that max remains always positive.
The mistake is "safe"---it will reject some blits, but will never cause
out-of-bounds writes.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 1455121059-18280-1-git-send-email-pbonzini@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
If dropping packets, data is freed, the caller's loop should not continue.
Reported by ccc-analyzer.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-id: 1456301288-1592-1-git-send-email-famz@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Using the return value to report errors is error prone:
- xics_alloc() returns -1 on error but spapr_vio_busdev_realize() errors
on 0
- xics_alloc_block() returns the unclear value of ics->offset - 1 on error
but both rtas_ibm_change_msi() and spapr_phb_realize() error on 0
This patch adds an errp argument to xics_alloc() and xics_alloc_block() to
report errors. The return value of these functions is a valid IRQ number
if errp is NULL. It is undefined otherwise.
The corresponding error traces get promotted to error messages. Note that
the "can't allocate IRQ" error message in spapr_vio_busdev_realize() also
moves to xics_alloc(). Similar error message consolidation isn't really
applicable to xics_alloc_block() because callers have extra context (device
config address, MSI or MSIX).
This fixes the issues mentioned above.
Based on previous work from Brian W. Hart.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Migration of pseries-2.3 doesn't have configuration section. Unfortunately,
QEMU 2.4/2.4.1/2.5 are buggy and always stream and expect the configuration
section, and break migration both ways.
This patch introduces a property which allows to enforce a configuration
section for machines who don't have one.
It can be set at startup:
-machine enforce-config-section=on
or later from the QEMU monitor:
qom-set /machine enforce-config-section on
It is up to the tooling to set or unset this property according to the
version of the QEMU at the other end of the pipe.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since QEMU 2.4, we have a configuration section in the migration stream.
This must be skipped for older machines, like it is already done for x86.
This patch fixes the migration of pseries-2.3 from/to QEMU 2.3, but it
breaks migration of the same machine from/to QEMU 2.4/2.4.1/2.5. We do
that anyway because QEMU 2.3 is likely to be more widely deployed than
newer QEMU versions.
Fixes: 61964c23e5
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
With this, it's easier to know if a guest uses an invalid and/or unimplemented
DMA channel.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since QEMU 2.3, we have a vmdesc section in the migration stream.
This section is not mandatory but when migrating a pseries-2.2
machine from QEMU 2.2, you get a warning at the destination:
qemu-system-ppc64: Expected vmdescription section, but got 0
The warning goes away if we decide to skip vmdesc as well for
older pseries, like it is already done for pc's.
This can only be observed with -cpu POWER7 because POWER8
cannot migrate from QEMU 2.2 to 2.3 (insns_flags2 mismatch).
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This RTAS call is used to request new interrupts or to free all interrupts.
If the driver has already allocated interrupts and asks again for a non-null
number of irqs, then the rtas_ibm_change_msi() function will silently leak
the previous interrupts.
It happens because xics_free() is only called when the driver releases all
interrupts (!req_num case). Note that the previously allocated spapr_pci_msi
is not leaked because the GHashTable is created with destroy functions and
g_hash_table_insert() hence frees the old value.
This patch makes sure any previously allocated MSIs are released when a
new allocation succeeds.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The num local variable is initialized to zero and has no writer.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It is currently possible to hotplug a spapr_rng device but QEMU crashes
when we try to hot unplug:
ERROR:hw/core/qdev.c:295:qdev_unplug: assertion failed: (hotplug_ctrl)
Aborted
This happens because spapr_rng isn't plugged to any bus and sPAPR does
not provide hotplug support for it: qdev_get_hotplug_handler() hence
return NULL and we hit the assertion.
And anyway, it doesn't make much sense to unplug this device since hcalls
cannot be unregistered. Even the idea of hotplugging a RNG device instead
of declaring it on the QEMU command line looks weird.
This patch simply disables hotpluggability for the spapr-rng class.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This quirk is a workaround for the following hardware behaviour, on
which UEFI (specifically, the bootloader for Windows on Pi2) depends:
1. at boot with an SD card present, the interrupt status/enable
registers are initially zero
2. upon enabling it in the interrupt enable register, the card insert
bit in the interrupt status register is immediately set
3. after a subsequent controller reset, the card insert interrupt does
not fire, even if enabled in the interrupt enable register
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1456436130-7048-3-git-send-email-Andrew.Baumann@microsoft.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This reverts commit 723697551a.
This change was poorly tested on my part. It squelched card insertion
interrupts on reset, but that was not necessary because sdhci_reset()
clears all the registers (via the call to memset), so the subsequent
sdhci_insert_eject_cb() call never sees the card insert interrupt
enabled. However, not calling the insert_eject_cb results in prnsts
remaining 0, when it actually needs to be updated to indicate card
presence and R/O status.
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1456436130-7048-2-git-send-email-Andrew.Baumann@microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Recent changes to sdhci broke SD on raspi. This change mirrors
the logic to create the SD card device at the board level.
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1456351128-5560-1-git-send-email-Andrew.Baumann@microsoft.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
pl061.c emulates two GPIO devices, ARM PL061 and TI Stellaris, which
share the same read/write functions (pl061_read and pl061_write).
However PL061 and Stellaris have different GPIO register definitions
and pl061_read()/pl061_write() doesn't check it. This patch enforces
checking on offset, preventing R/W into the reserved memory area.
Signed-off-by: Wei Huang <wei@redhat.com>
Message-id: 1455814580-17699-1-git-send-email-wei@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When I reviewed Marc's fw_cfg DMA patches, I completely missed that the
way we set dma_enabled would break migration.
Gerd explained the right way (see reference below): dma_enabled should be
set to true by default, and only true->false transitions should be
possible:
- when the user requests that with
-global fw_cfg_mem.dma_enabled=off
or
-global fw_cfg_io.dma_enabled=off
as appropriate for the platform,
- when HW_COMPAT_2_4 dictates it,
- when board code initializes fw_cfg without requesting DMA support.
Cc: Marc Marí <markmb@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Alexandre DERUMIER <aderumier@odiso.com>
Cc: qemu-stable@nongnu.org
Ref: http://thread.gmane.org/gmane.comp.emulators.qemu/390272/focus=391042
Ref: https://bugs.launchpad.net/qemu/+bug/1536487
Suggested-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 1455823860-22268-1-git-send-email-lersek@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Fixes all over the place.
virtio dataplane migration support.
Old q35 machine types removed.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWzuKeAAoJECgfDbjSjVRpGzIH/1Tz6CoEq1rowiyVJ9B80oQU
gDI2YWnJDSwJllmAF0rmoPRBQR8op3ZETZiCAcADHoZ7kdBNWGbyQeaDrrEPH7Q/
rCDVt8Q3g80vs89aWKG0nQ16J2MW5TbkuiQw7pjQSdc9AbUdWpUqSiWnpZ+sPAql
6DuVpjQ4/rN2alucXoa1Sir8KDDV7kBuY8U6/KoY890qzh842dv2523qvuCza9yR
KX8Imj3oQAFjFSv5t1aOD3yYvWFd73EsReHPLGb1JtsVr/6wjs0sFUyA3JicBgnT
+kWoSObWikfDY69HnqTkJpkun6woMM3zW5h2SkUBf9QP3yqLfGIp9uSriNN84Ak=
=KXyh
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
vhost, virtio, pci, pc
Fixes all over the place.
virtio dataplane migration support.
Old q35 machine types removed.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 25 Feb 2016 11:16:46 GMT using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream: (21 commits)
q35: No need to check gigabyte_align
q35: Remove unused q35-acpi-dsdt.aml file
ich9: Remove enable_tco arguments from init functions
machine: Remove no_tco field
q35: Remove old machine versions
tests/vhost-user-bridge: fix build on 32 bit systems
vring: remove
virtio-scsi: do not use vring in dataplane
virtio-blk: do not use vring in dataplane
virtio-blk: fix "disabled data plane" mode
virtio: export vring_notify as virtio_should_notify
virtio: add AioContext-specific function for host notifiers
vring: make vring_enable_notification return void
block-migration: acquire AioContext as necessary
pci core: function pci_bus_init() cleanup
pci core: function pci_host_bus_register() cleanup
balloon: Use only 'pc-dimm' type dimm for ballooning
virtio-balloon: rewrite get_current_ram_size()
move get_current_ram_size to virtio-balloon.c
vhost-user: don't merge regions with different fds
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
gigabyte_align is always true on q35, so we don't need the
!gigabyte_align compat code anymore.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
The file was used only by older machine-types, and it is not
needed anymore.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
The enable_tco arguments are always true, so they are not needed
anymore.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
The field is always set to zero, so it is not necessary anymore.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Migration with q35 was not possible before commit
04329029a8, because q35
unconditionally creates an ich9-ahci device, that was marked as
unmigratable. So all q35 machine classes before pc-q35-2.4 were
not migratable, so there's no point in keeping compatibility code
for them.
Remove all old pc-q35 machine classes and keep only pc-q35-2.4
and newer.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
In disabled mode, virtio-blk dataplane seems to be enabled, but flow
actually goes through the normal virtio path. This patch simplifies a bit
the handling of disabled mode. In disabled mode, virtio_blk_handle_output
might be called even if s->dataplane is not NULL.
This is a bit tricky, because the current check for s->dataplane will
always trigger, causing a continuous stream of calls to
virtio_blk_data_plane_start. Unfortunately, these calls will not
do anything. To fix this, set the "started" flag even in disabled
mode, and skip virtio_blk_data_plane_start if the started flag is true.
The resulting changes also prepare the code for the next patch, were
virtio-blk dataplane will reuse the same virtio_blk_handle_output function
as "regular" virtio-blk.
Because struct VirtIOBlockDataPlane is opaque in virtio-blk.c, we have
to move s->dataplane->started inside struct VirtIOBlock.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Virtio dataplane needs to trigger the irq manually through the
guest notifier. Export virtio_should_notify so that it can be
used around event_notifier_set.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
This is used to register ioeventfd with a dataplane thread.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Make the API more similar to the regular virtqueue API. This will
help when modifying the code to not use vring.c anymore.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
remove unused param
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
remove unused param, and rename the other to a meaningful one.
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
For now there are only two dimm's: pc-dimm and nvdimm. This patch is
actually needed to disable ballooning on nvdimm. But, to avoid future
bugs, instead of disallowing nvdimm, we allow only pc-dimm. So, if
someone adds new dimm which should be balloon-able, then this ability
should be explicitly specified here.
Why ballooning for nvdimm should be disabled for now:
NVDIMM for now is planned to use as a backing store for DAX filesystem
in the guest and thus this memory is excluded from guest memory
management and LRUs.
In this case libvirt running QEMU along with configured balloon almost
immediately inflates balloon and effectively kill the guest as
qemu counts nvdimm as part of the ram.
Counting dimm devices as part of the ram for ballooning was started from
commit 463756d03:
virtio-balloon: Fix balloon not working correctly when hotplug memory
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use pc_dimm_built_list() instead of qmp_pc_dimm_device_list()
Actually, Qapi is not related to this internal helper.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This fixes a crash in the target QEMU during migration.
Broken in commit c5f54f3.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[reworded commit message]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This hypercall either initializes a page with zeros, or copies
another page.
According to LoPAPR, the i-cache of the page should also be
flushed if using H_ICACHE_INVALIDATE or H_ICACHE_SYNCHRONIZE,
and the d-cache should be synchronized to the RAM if the
H_ICACHE_SYNCHRONIZE flag is used. For this, two new functions
are introduced, kvmppc_dcbst_range() and kvmppc_icbi()_range, which
use the corresponding assembler instructions to flush the caches
if running with KVM on Power. If the code runs with TCG instead,
the code only uses tb_flush(), assuming that this will be
enough for synchronization.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
---
This just catches a couple of stragglers since I posted
the last clean-includes patchset last week.
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
get_current_ram_size() is used only in virtio-balloon.c
This patch moves it into virtio-balloon and make it static, to allow
some balloon-specific tuning.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost currently merges regions with contiguious virtual and physical
addresses. This breaks for vhost-user since that also needs fds to
match.
Add a vhost_ops entry to compare the fds for vhost-user only.
Cc: qemu-stable@nongnu.org
Cc: Victor Kaplansky <victork@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
While guest/host ABI is documented in hw/acpi/bios-linker-loader.c,
the API was left undocumented.
This adds documentation for all API functions.
Additionally, input is validated to make sure all
pointers fall within range of provided files.
To allow this validation for checksum commands,
bios_linker_loader_add_checksum is changed to accept GArray * in place
of void *.
Reported-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Allocate timer once, at init time, instead of allocating/freeing
it all the time when starting/stopping the bus. Simplifies the
code, also fixes bugs (memory leak) due to missing checks whenever
the time is already allocated or not.
Cc: Prasad J Pandit <pjp@fedoraproject.org>
Reported-by: Zuozhi Fzz <zuozhi.fzz@alibaba-inc.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
pid can be gotten from uhci device memory in uhci_handle_td(),
so the guest can trigger assert qemu if we get an invalid pid.
And the uhci spec 2.1.2 tells us The Host Controller sets Host
Controller Process Error bit to 1 when it detects a fatal error
and indicates that the Host Controller suffered a consistency
check failure while processing a Transfer Descriptor. An example
of a consistency check failure would be finding an illegal PID
field while processing the packet header portion of the TD.
When this error occurs, the Host Controller clears the Run/Stop
bit in the Command register to prevent further schedule execution.
We'd better to set UHCI_STS_HCPERR and kick an interrupt, check
the pid value at the first of uhci_handle_td function.
https://bugzilla.redhat.com/show_bug.cgi?id=1070027
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Message-id: 1455867238-4720-1-git-send-email-arei.gonglei@huawei.com
[ applied minor codestyle fix ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When processing remote NDIS control message packets,
the USB Net device emulator uses a fixed length(4096) data buffer.
The incoming informationBufferOffset & Length combination could
overflow and cross that range. Check control message buffer
offsets and length to avoid it.
Reported-by: Qinghao Tang <luodalongde@gmail.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1455648821-17340-3-git-send-email-ppandit@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When processing remote NDIS control message packets, the USB Net
device emulator uses a fixed length(4096) data buffer. The incoming
packet length could exceed this limit. Add a check to avoid it.
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1455648821-17340-2-git-send-email-ppandit@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
