The distance in phrase operator must be an integer value between zero
and MAXENTRYPOS inclusive. But previously the error message about
its valid value included the information about its upper limit
but not lower limit (i.e., zero). This commit improves the error message
so that it also includes the information about its lower limit.
Back-patch to v9.6 where full-text phrase search was supported.
Author: Kyotaro Horiguchi
Reviewed-by: Fujii Masao
Discussion: https://postgr.es/m/20210819.170315.1413060634876301811.horikyota.ntt@gmail.com
Regexps like "(.){0}...\1" drew an "invalid backreference number".
That's not unreasonable on its face, since the capture group will
never be matched if it's iterated zero times. However, other engines
such as Perl's don't complain about this, nor do we throw an error for
related cases such as "(.)|\1", even though that backref can never
succeed either. Also, if the zero-iterations case happens at runtime
rather than compile time --- say, "(x)*...\1" when there's no "x" to
be found --- that's not an error, we just deem the backref to not
match. Making this even less defensible, no error was thrown for
nested cases such as "((.)){0}...\2"; and to add insult to injury,
those cases could result in assertion failures instead. (It seems
that nothing especially bad happened in non-assert builds, though.)
Let's just fix it so that no error is thrown and instead the backref
is deemed to never match, so that compile-time detection of no
iterations behaves the same as run-time detection.
Per report from Mark Dilger. This appears to be an aboriginal error
in Spencer's library, so back-patch to all supported versions.
Pre-v14, it turns out to also be necessary to back-patch one aspect of
commits cb76fbd7e/00116dee5, namely to create capture-node subREs with
the begin/end states of their subexpressions, not the current lp/rp
of the outer parseqatom invocation. Otherwise delsub complains that
we're trying to disconnect a state from itself. This is a bit scary
but code examination shows that it's safe: in the pre-v14 code, if we
want to wrap iteration around the subexpression, the first thing we do
is overwrite the atom's begin/end fields with new states. So the
bogus values didn't survive long enough to be used for anything, except
if no iteration is required, in which case it doesn't matter.
Discussion: https://postgr.es/m/A099E4A8-4377-4C64-A98C-3DEDDC075502@enterprisedb.com
The recursion in cdissect() was careless about clearing match data
for capturing parentheses after rejecting a partial match. This
could allow a later back-reference to succeed when by rights it
should fail for lack of a defined referent.
To fix, think a little more rigorously about what the contract
between different levels of cdissect's recursion needs to be.
With the right spec, we can fix this using fewer rather than more
resets of the match data; the key decision being that a failed
sub-match is now explicitly responsible for clearing any matches
it may have set.
There are enough other cross-checks and optimizations in the code
that it's not especially easy to exhibit this problem; usually, the
match will fail as-expected. Plus, regexps that are even potentially
vulnerable are most likely user errors, since there's just not much
point in writing a back-ref that doesn't always have a referent.
These facts perhaps explain why the issue hasn't been detected,
even though it's almost certainly a couple of decades old.
Discussion: https://postgr.es/m/151435.1629733387@sss.pgh.pa.us
WAL records may span multiple segments, but XLogWrite() does not
wait for the entire record to be written out to disk before
creating archive status files. Instead, as soon as the last WAL page of
the segment is written, the archive status file is created, and the
archiver may process it. If PostgreSQL crashes before it is able to
write and flush the rest of the record (in the next WAL segment), the
wrong version of the first segment file lingers in the archive, which
causes operations such as point-in-time restores to fail.
To fix this, keep track of records that span across segments and ensure
that segments are only marked ready-for-archival once such records have
been completely written to disk.
This has always been wrong, so backpatch all the way back.
Author: Nathan Bossart <bossartn@amazon.com>
Reviewed-by: Kyotaro Horiguchi <horikyota.ntt@gmail.com>
Reviewed-by: Ryo Matsumura <matsumura.ryo@fujitsu.com>
Reviewed-by: Andrey Borodin <x4mmm@yandex-team.ru>
Discussion: https://postgr.es/m/CBDDFA01-6E40-46BB-9F98-9340F4379505@amazon.com
After detecting a sub-match "dissect" failure (i.e., a backref match
failure) in the i'th sub-match of an iteration node, we should proceed
by adjusting the attempted length of the i'th submatch. As coded,
though, these functions changed the attempted length of the *last*
sub-match, and only after exhausting all possibilities for that would
they back up to adjust the next-to-last sub-match, and then the
second-from-last, etc; all of which is wasted effort, since only
changing the start or length of the i'th sub-match can possibly make
it succeed. This oversight creates the possibility for exponentially
bad performance. Fortunately the problem is masked in most cases by
optimizations or constraints applied elsewhere; which explains why
we'd not noticed it before. But it is possible to reach the problem
with fairly simple, if contrived, regexps.
Oversight in my commit 173e29aa5. That's pretty ancient now,
so back-patch to all supported branches.
Discussion: https://postgr.es/m/1808998.1629412269@sss.pgh.pa.us
transformLockingClause neglected to exclude the pseudo-RTEs for
OLD/NEW when processing a rule's query. This led to odd errors
or even crashes later on. This bug is very ancient, but it's
not terribly surprising that nobody noticed, since the use-case
for SELECT FOR UPDATE in a non-view rule is somewhere between
thin and non-existent. Still, crashing is not OK.
Per bug #17151 from Zhiyong Wu. Thanks to Masahiko Sawada
for analysis of the problem.
Discussion: https://postgr.es/m/17151-c03a3e6e4ec9aadb@postgresql.org
Recursion into the FILTER clause was mis-implemented, such that a
relevant Var or Aggref at the very top of the FILTER clause would
be ignored. (Of course, that'd have to be a plain boolean Var or
boolean-returning aggregate.) The consequence would be
mis-identification of the correct semantic level of the aggregate,
which could lead to not-per-spec query behavior. If the FILTER
expression is an aggregate, this could also lead to failure to issue
an expected "aggregate function calls cannot be nested" error, which
would likely result in a core dump later on, since the planner and
executor aren't expecting such cases to appear.
The root cause is that commit b560ec1b0 blindly copied some code
that assumed it's recursing into a List, and thus didn't examine the
top-level node. To forestall questions about why this call doesn't
look like the others, as well as possible future copy-and-paste
mistakes, let's change all three check_agg_arguments_walker calls in
check_agg_arguments, even though only the one for the filter clause
is really broken.
Per bug #17152 from Zhiyong Wu. This has been wrong since we
implemented FILTER, so back-patch to all supported versions.
(Testing suggests that pre-v11 branches manage to avoid crashing
in the bad-Aggref case, thanks to "redundant" checks in ExecInitAgg.
But I'm not sure how thorough that protection is, and anyway the
wrong-behavior issue remains, so fix 9.6 and 10 too.)
Discussion: https://postgr.es/m/17152-c7f906cc1a88e61b@postgresql.org
In OpenSSL there are two types of BIO's (I/O abstractions):
source/sink and filters. A source/sink BIO is a source and/or
sink of data, ie one acting on a socket or a file. A filter
BIO takes a stream of input from another BIO and transforms it.
In order for BIO_find_type() to be able to traverse the chain
of BIO's and correctly find all BIO's of a certain type they
shall have the type bit set accordingly, source/sink BIO's
(what PostgreSQL implements) use BIO_TYPE_SOURCE_SINK and
filter BIO's use BIO_TYPE_FILTER. In addition to these, file
descriptor based BIO's should have the descriptor bit set,
BIO_TYPE_DESCRIPTOR.
The PostgreSQL implementation didn't set the type bits, which
went unnoticed for a long time as it's only really relevant
for code auditing the OpenSSL installation, or doing similar
tasks. It is required by the API though, so this fixes it.
Backpatch through 9.6 as this has been wrong for a long time.
Author: Itamar Gafni
Discussion: https://postgr.es/m/SN6PR06MB39665EC10C34BB20956AE4578AF39@SN6PR06MB3966.namprd06.prod.outlook.com
Backpatch-through: 9.6
This commit ensures that the wait interval in the replay delay loop
waiting for an amount of time defined by recovery_min_apply_delay is
correctly handled on reload, recalculating the delay if this GUC value
is updated, based on the timestamp of the commit record being replayed.
The previous behavior would be problematic for example with replay
still waiting even if the delay got reduced or just cancelled. If the
apply delay was increased to a larger value, the wait would have just
respected the old value set, finishing earlier.
Author: Soumyadeep Chakraborty, Ashwin Agrawal
Reviewed-by: Kyotaro Horiguchi, Michael Paquier
Discussion: https://postgr.es/m/CAE-ML+93zfr-HLN8OuxF0BjpWJ17O5dv1eMvSE5jsj9jpnAXZA@mail.gmail.com
Backpatch-through: 9.6
Like the ARM case, just use gcc's __sync_lock_test_and_set();
that will compile into AMOSWAP.W.AQ which does what we need.
At some point it might be worth doing some work on atomic ops
for RISC-V, but this should be enough for a creditable port.
Back-patch to all supported branches, just in case somebody
wants to try them on RISC-V.
Marek Szuba
Discussion: https://postgr.es/m/dea97b6d-f55f-1f6d-9109-504aa7dfa421@gentoo.org
It's hard to disable ASLR on current macOS releases, for testing with
-DEXEC_BACKEND. You could already set the environment variable
PG_SHMEM_ADDR to something not likely to collide with mappings created
earlier in process startup. Let's also provide a default value that
works on current releases and architectures, for developer convenience.
As noted in the pre-existing comment, this is a horrible hack, but
-DEXEC_BACKEND is only used by Unix-based PostgreSQL developers for
testing some otherwise Windows-only code paths, so it seems excusable.
Back-patch to all supported branches.
Reviewed-by: Tom Lane <tgl@sss.pgh.pa.us>
Discussion: https://postgr.es/m/20210806032944.m4tz7j2w47mant26%40alap3.anarazel.de
As a result of confusion about whether the "char" type is signed or
unsigned, scans for index searches like "col < 'x'" or "col <= 'x'"
would start at the middle of the index not the left end, thus missing
many or all of the entries they should find. Fortunately, this
is not a symptom of index corruption. It's only the search logic
that is broken, and we can fix it without unpleasant side-effects.
Per report from Jason Kim. This has been wrong since btree_gin's
beginning, so back-patch to all supported branches.
Discussion: https://postgr.es/m/20210810001649.htnltbh7c63re42p@jasonk.me
In ec34040af I added a mention that there was no point in setting
maintenance_work_limit to anything higher than 1GB for vacuum, but that
was incorrect as ginInsertCleanup() also looks at what
maintenance_work_mem is set to during VACUUM and that's not limited to
1GB.
Here I attempt to make it more clear that the limitation is only around
the number of dead tuple identifiers that we can collect during VACUUM.
I've also added a note to autovacuum_work_mem to mention this limitation.
I didn't do that in ec34040af as I'd had some wrong-headed ideas about
just limiting the maximum value for that GUC to 1GB.
Author: David Rowley
Discussion: https://postgr.es/m/CAApHDvpGwOAvunp-E-bN_rbAs3hmxMoasm5pzkYDbf36h73s7w@mail.gmail.com
Backpatch-through: 9.6, same as ec34040af
Since commit e462856a7a, pg_upgrade automatically creates a script to
update extensions, so mention that instead of ALTER EXTENSION.
Backpatch-through: 9.6
Copy-and-pasteo in 665c5855e, evidently. The 9.6 docs toolchain
whined about duplicate index entries, though our modern toolchain
doesn't. In any case, these GUCs surely are not about the
default settings of these values.
Rather than trying to pick table aliases that won't conflict with
any possible user-defined matview column name, adjust the queries'
syntax so that the aliases are only used in places where they can't be
mistaken for column names. Mostly this consists of writing "alias.*"
not just "alias", which adds clarity for humans as well as machines.
We do have the issue that "SELECT alias.*" acts differently from
"SELECT alias", but we can use the same hack ruleutils.c uses for
whole-row variables in SELECT lists: write "alias.*::compositetype".
We might as well revert to the original aliases after doing this;
they're a bit easier to read.
Like 75d66d10e, back-patch to all supported branches.
Discussion: https://postgr.es/m/2488325.1628261320@sss.pgh.pa.us
Formerly, the numeric code tested whether an integer value of a larger
type would fit in a smaller type by casting it to the smaller type and
then testing if the reverse conversion produced the original value.
That's perfectly fine, except that it caused a test failure on
buildfarm animal castoroides, most likely due to a compiler bug.
Instead, do these tests by comparing against PG_INT16/32_MIN/MAX. That
matches existing code in other places, such as int84(), which is more
widely tested, and so is less likely to go wrong.
While at it, add regression tests covering the numeric-to-int8/4/2
conversions, and adjust the recently added tests to the style of
434ddfb79a (on the v11 branch) to make failures easier to diagnose.
Per buildfarm via Tom Lane, reviewed by Tom Lane.
Discussion: https://postgr.es/m/2394813.1628179479%40sss.pgh.pa.us
This fixes a long-standing bug when using to_char() to format a
numeric value in scientific notation -- if the value's exponent is
less than -NUMERIC_MAX_DISPLAY_SCALE-1 (-1001), it produced a
division-by-zero error.
The reason for this error was that get_str_from_var_sci() divides its
input by 10^exp, which it produced using power_var_int(). However, the
underflow test in power_var_int() causes it to return zero if the
result scale is too small. That's not a problem for power_var_int()'s
only other caller, power_var(), since that limits the rscale to 1000,
but in get_str_from_var_sci() the exponent can be much smaller,
requiring a much larger rscale. Fix by introducing a new function to
compute 10^exp directly, with no rscale limit. This also allows 10^exp
to be computed more efficiently, without any numeric multiplication,
division or rounding.
Discussion: https://postgr.es/m/CAEZATCWhojfH4whaqgUKBe8D5jNHB8ytzemL-PnRx+KCTyMXmg@mail.gmail.com
This fixes a couple of related problems that arise when raising
numbers to very large powers.
Firstly, when raising a negative number to a very large integer power,
the result should be well-defined, but the previous code would only
cope if the exponent was small enough to go through power_var_int().
Otherwise it would throw an internal error, attempting to take the
logarithm of a negative number. Fix this by adding suitable handling
to the general case in power_var() to cope with negative bases,
checking for integer powers there.
Next, when raising a (positive or negative) number whose absolute
value is slightly less than 1 to a very large power, the result should
approach zero as the power is increased. However, in some cases, for
sufficiently large powers, this would lose all precision and return 1
instead of 0. This was due to the way that the local_rscale was being
calculated for the final full-precision calculation:
local_rscale = rscale + (int) val - ln_dweight + 8
The first two terms on the right hand side are meant to give the
number of significant digits required in the result ("val" being the
estimated result weight). However, this failed to account for the fact
that rscale is clipped to a maximum of NUMERIC_MAX_DISPLAY_SCALE
(1000), and the result weight might be less then -1000, causing their
sum to be negative, leading to a loss of precision. Fix this by
forcing the number of significant digits calculated to be nonnegative.
It's OK for it to be zero (when the result weight is less than -1000),
since the local_rscale value then includes a few extra digits to
ensure an accurate result.
Finally, add additional underflow checks to exp_var() and power_var(),
so that they consistently return zero for cases like this where the
result is indistinguishable from zero. Some paths through this code
already returned zero in such cases, but others were throwing overflow
errors.
Dean Rasheed, reviewed by Yugo Nagata.
Discussion: http://postgr.es/m/CAEZATCW6Dvq7+3wN3tt5jLj-FyOcUgT5xNoOqce5=6Su0bCR0w@mail.gmail.com
If a file is truncated, we must update minRecoveryPoint. Once a file is
truncated, there's no going back; it would not be safe to stop recovery
at a point earlier than that anymore.
Commit 7bffc9b7bf changed xact_redo_commit() so that it updates
minRecoveryPoint on truncation, but forgot to change xact_redo_abort().
Back-patch to all supported versions.
Reported-by: mengjuan.cmj@alibaba-inc.com
Author: Fujii Masao
Reviewed-by: Heikki Linnakangas
Discussion: https://postgr.es/m/b029fce3-4fac-4265-968e-16f36ff4d075.mengjuan.cmj@alibaba-inc.com
This changes the behavior of examining the pg_file_settings view after
changing a config option that requires restart. The user needs to know
that any change of such options does not take effect until a restart,
and this worked correctly if the line is edited without removing it.
However, for the case where the line is removed altogether, the flag
doesn't get set, because a flag was only set in set_config_option, but
that's not called for lines removed. Repair.
(Ref.: commits 62d16c7fc5 and a486e35706)
Author: Álvaro Herrera <alvherre@alvh.no-ip.org>
Reviewed-by: Daniel Gustafsson <daniel@yesql.se>
Reviewed-by: Tom Lane <tgl@sss.pgh.pa.us>
Discussion: https://postgr.es/m/202107262302.xsfdfc5sb7sh@alvherre.pgsql
The error messages using the word "non-negative" are confusing
because it's ambiguous about whether it accepts zero or not.
This commit improves those error messages by replacing it with
less ambiguous word like "greater than zero" or
"greater than or equal to zero".
Also this commit added the note about the word "non-negative" to
the error message style guide, to help writing the new error messages.
When postgres_fdw option fetch_size was set to zero, previously
the error message "fetch_size requires a non-negative integer value"
was reported. This error message was outright buggy. Therefore
back-patch to all supported versions where such buggy error message
could be thrown.
Reported-by: Hou Zhijie
Author: Bharath Rupireddy
Reviewed-by: Kyotaro Horiguchi, Fujii Masao
Discussion: https://postgr.es/m/OS0PR01MB5716415335A06B489F1B3A8194569@OS0PR01MB5716.jpnprd01.prod.outlook.com
Add pg_resetxlog -u option to set the oldest xid in pg_control.
Previously -x set this value be -2 billion less than the -x value.
However, this causes the server to immediately scan all relation's
relfrozenxid so it can advance pg_control's oldest xid to be inside the
autovacuum_freeze_max_age range, which is inefficient and might disrupt
diagnostic recovery. pg_upgrade will use this option to better create
the new cluster to match the old cluster.
Reported-by: Jason Harvey, Floris Van Nee
Discussion: https://postgr.es/m/20190615183759.GB239428@rfd.leadboat.com, 87da83168c644fd9aae38f546cc70295@opammb0562.comp.optiver.com
Author: Bertrand Drouvot
Backpatch-through: 9.6
This commit changes the startup process in the standby server so that
it handles the interrupt signals after waiting for wal_retrieve_retry_interval
on the latch and resetting it, before entering another wait on the latch.
This change causes the standby server to promptly handle interrupt signals.
Otherwise, previously, there was the case where the standby needs to
wait extra five seconds to shutdown when the shutdown request arrived
while the startup process was waiting for wal_retrieve_retry_interval
on the latch.
Author: Fujii Masao, but implementation idea is from Soumyadeep Chakraborty
Reviewed-by: Soumyadeep Chakraborty
Discussion: https://postgr.es/m/9d7e6ab0-8a53-ddb9-63cd-289bcb25fe0e@oss.nttdata.com
Per discussion of BUG #17073, back-patch to all supported versions.
Discussion: https://postgr.es/m/17073-1a5fdaed0fa5d4d0@postgresql.org
We have an implementation restriction that PREPARE TRANSACTION can't
handle cases where both session-lifespan and transaction-lifespan locks
are held on the same lockable object. (That's because we'd otherwise
need to acquire a new PROCLOCK entry during post-prepare cleanup, which
is an operation that might fail. The situation can only arise with odd
usages of advisory locks, so removing the restriction is probably not
worth the amount of effort it would take.) AtPrepare_Locks attempted
to enforce this, but its logic was many bricks shy of a load, because
it only detected cases where the session and transaction locks had the
same lockmode. Locks of different modes on the same object would lead
to the rather unhelpful message "PANIC: we seem to have dropped a bit
somewhere".
To fix, build a transient hashtable with one entry per locktag,
not one per locktag + mode, and use that to detect conflicts.
Per bug #17122 from Alexander Pyhalov. This bug is ancient,
so back-patch to all supported branches.
Discussion: https://postgr.es/m/17122-04f3c32098a62233@postgresql.org
We previously took a hard-line attitude that callers should never print
a null string pointer, and doing so is worthy of an assertion failure
or crash. However, we've long since flushed out any easy-to-find bugs
of that nature. What remains is a lot of code that perhaps could fail
that way in hard-to-reach corner cases. For example, in something as
simple as
ereport(ERROR,
(errcode(ERRCODE_UNDEFINED_OBJECT),
errmsg("constraint \"%s\" for table \"%s\" does not exist",
conname, get_rel_name(relid))));
one must wonder whether it's completely guaranteed that get_rel_name
cannot return NULL in this context. If such a situation did occur,
the existing policy converts what might be a pretty minor bug into
a server crash condition. This is not good for robustness.
Hence, let's follow the lead of glibc and print "(null)" instead
of failing. We should, of course, still consider it a bug if that
behavior is reachable in ordinary use; but crashing seems less
desirable than not crashing.
This fix works across-the-board in v12 and up, where we always use
src/port/snprintf.c. Before that, on most platforms we're at the mercy
of the local libc, but it appears that Solaris 10 is the only supported
platform where we'd still get a crash. Most other platforms such as
*BSD, macOS, and Solaris 11 have adopted glibc's behavior at some
point. (AIX and HPUX just print "" not "(null)", but that's close
enough.) I've not checked what Windows' native printf would do, but
it doesn't matter because we've long used snprintf.c on that platform.
In v12 and up, also const-ify related code so that we're not casting
away const on the constant string. This is just neatnik-ism, since
next to no compilers will warn about that.
Discussion: https://postgr.es/m/17098-b960f3616c861f83@postgresql.org
If an error was raised during our initial attempt to check whether
a successfully-compiled expression is "simple", subsequent calls of
exec_stmt_execsql would suppose that stmt->mod_stmt was already computed
when it had not been. This could lead to assertion failures in debug
builds; in production builds the effect would typically be to act as
if INTO STRICT had been specified even when it had not been. Of course
that only matters if the subsequent attempt to execute the expression
succeeds, so that the problem can only be reached by fixing a failure
in some referenced, inline-able SQL function and then retrying the
calling plpgsql function in the same session.
(There might be even-more-obscure ways to change the expression's
behavior without changing the plpgsql function, but that one seems
like the only one people would be likely to hit in practice.)
The most foolproof way to fix this would be to arrange for
exec_prepare_plan to not set expr->plan until we've finished the
subsidiary simple-expression check. But it seems hard to do that
without creating reference-count leak issues. So settle for documenting
the hazard in a comment and fixing exec_stmt_execsql to test separately
for whether it's computed stmt->mod_stmt. (That adds a test-and-branch
per execution, but hopefully that's negligible in context.) In v11 and
up, also fix exec_stmt_call which had a variant of the same issue.
Per bug #17113 from Alexander Lakhin. Back-patch to all
supported branches.
Discussion: https://postgr.es/m/17113-077605ce00e0e7ec@postgresql.org
We had documentation of default_transaction_isolation et al,
but for some reason not of transaction_isolation et al.
AFAICS this is just an ancient oversight, so repair.
Per bug #17077 from Yanliang Lei.
Discussion: https://postgr.es/m/17077-ade8e166a01e1374@postgresql.org
41469253e went to the trouble of removing a theoretical bug from
free_sort_tuple by checking if the tuple was NULL before freeing it. Let's
make this a little more robust by also setting the tuple to NULL so that
should we be called again we won't end up doing a pfree on the already
pfree'd tuple. Per advice from Tom Lane.
Discussion: https://postgr.es/m/3188192.1626136953@sss.pgh.pa.us
Backpatch-through: 9.6, same as 41469253e
This fixes a theoretical bug in tuplesort.c which, if a bounded sort was
used in combination with a byval Datum sort (tuplesort_begin_datum), when
switching the sort to a bounded heap in make_bounded_heap(), we'd call
free_sort_tuple(). The problem was that when sorting Datums of a byval
type, the tuple is NULL and free_sort_tuple() would free the memory for it
regardless of that. This would result in a crash.
Here we fix that simply by adding a check to see if the tuple is NULL
before trying to disassociate and free any memory belonging to it.
The reason this bug is only theoretical is that nowhere in the current
code base do we do tuplesort_set_bound() when performing a Datum sort.
However, let's backpatch a fix for this as if any extension uses the code
in this way then it's likely to cause problems.
Author: Ronan Dunklau
Discussion: https://postgr.es/m/CAApHDvpdoqNC5FjDb3KUTSMs5dg6f+XxH4Bg_dVcLi8UYAG3EQ@mail.gmail.com
Backpatch-through: 9.6, oldest supported version
This should have been removed in commit 7e30c186da, which split the loop
into two. Only the first loop uses the 'from' variable; updating it in
the second loop is bogus. It was never read after the first loop, so this
was harmless and surely optimized away by the compiler, but let's be tidy.
Backpatch to all supported versions.
Author: Ranier Vilela
Discussion: https://www.postgresql.org/message-id/CAEudQAoWq%2BAL3BnELHu7gms2GN07k-np6yLbukGaxJ1vY-zeiQ%40mail.gmail.com
Although we were careful to lock the object being added or dropped,
we failed to get any sort of lock on the extension itself. This
allowed the ALTER to proceed in parallel with a DROP EXTENSION,
which is problematic for a couple of reasons. If both commands
succeeded we'd be left with a dangling link in pg_depend, which
would cause problems later. Also, if the ALTER failed for some
reason, it might try to print the extension's name, and that could
result in a crash or (in older branches) a silly error message
complaining about extension "(null)".
Per bug #17098 from Alexander Lakhin. Back-patch to all
supported branches.
Discussion: https://postgr.es/m/17098-b960f3616c861f83@postgresql.org
This fixes an overflow error when using the numeric * operator if the
result has more than 16383 digits after the decimal point by rounding
the result. Overflow errors should only occur if the result has too
many digits *before* the decimal point.
Discussion: https://postgr.es/m/CAEZATCUmeFWCrq2dNzZpRj5+6LfN85jYiDoqm+ucSXhb9U2TbA@mail.gmail.com
I incorrectly diagnosed the reason why hoverfly is unhappy.
Looking closer, it appears that it fails to link libldap
unless libssl is also present; so the problem was my
idea of clearing LIBS before making the check. Revert
to essentially the original coding, except that instead
of failing when libldap_r isn't there, use libldap.
Per buildfarm member hoverfly.
Discussion: https://postgr.es/m/17083-a19190d9591946a7@postgresql.org
In commit d0a02bdb8, I'd supposed that uniformly probing for
ldap_bind would make the intent clearer. However, that seems
not to work on AIX, for obscure reasons (maybe it's a macro
there?). Revert to the former behavior of probing
ldap_simple_bind for thread-safe cases and ldap_bind otherwise.
Per buildfarm member hoverfly.
Discussion: https://postgr.es/m/17083-a19190d9591946a7@postgresql.org
The separate libldap_r is gone and libldap itself is now always
thread-safe. Unfortunately there seems no easy way to tell by
inspection whether libldap is thread-safe, so we have to take
it on faith that libldap is thread-safe if there's no libldap_r.
That should be okay, as it appears that libldap_r was a standard
part of the installation going back at least 20 years.
Report and patch by Adrian Ho. Back-patch to all supported
branches, since people might try to build any of them with
a newer OpenLDAP.
Discussion: https://postgr.es/m/17083-a19190d9591946a7@postgresql.org
Since the executor can't cope with a utility statement appearing
as a node of a plan tree, we can't support cases where a rewrite
rule inserts a NOTIFY into an INSERT/UPDATE/DELETE command appearing
in a WITH clause of a larger query. (One can imagine ways around
that, but it'd be a new feature not a bug fix, and so far there's
been no demand for it.) RewriteQuery checked for this, but it
missed the case where the DML command rewrites to *only* a NOTIFY.
That'd lead to crashes later on in planning. Add the missed check,
and improve the level of testing of this area.
Per bug #17094 from Yaoguang Chen. It's been busted since WITH
was introduced, so back-patch to all supported branches.
Discussion: https://postgr.es/m/17094-bf15dff55eaf2e28@postgresql.org
Fujii Masao