* Make index numbering consistant (0-n vs 1-n)
* Add a little more tracing to PLLCalibrate because
we were missing a failure situation
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42158 a95241bf-73f2-0310-859d-f6bbb57e9c96
ensure that we don't block on the tty buffer, we chop up the data into blocks
that are written into the tty and then the buffer is flushed to the device
each time. This resolves the issue that a quick open/write/close would not
actually send the data to the device as it would cancel the transfer before
the output thread had a chance to run.
* Use the tty_close_cookie() call. Doing the close before waiting for the input
thread ensures that it is woken up if it blocked on writing into the tty.
* Correct the type of the USB callback status and only try to clear a halt if
the device was actually stalled.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42156 a95241bf-73f2-0310-859d-f6bbb57e9c96
available as a module function as well.
* Remove some unneeded resetting from tty_destroy_cookie.
* Move the public module functions to the public API section of the file and
order them by their declaration order in the module info.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42154 a95241bf-73f2-0310-859d-f6bbb57e9c96
to op which would've caused a wrong line state to be set.
* Add some more allocation checks.
* Some cleanup.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42151 a95241bf-73f2-0310-859d-f6bbb57e9c96
* Add crtid to register struct
* Disable VGA mode on FrameBuffer set (enables extended mode setting)
* Disable blanking calculations and setting more gracefully via if 0
* Add a *large* amount of code to Set/Calculate/Calibrate PLL
* Disable PLL on removal of accel.
* Remove junk comments on overscan
* Enable pixel clock limit pulling
* write32AtMask style cleanup
* Rename ReadMC to be more consistant
(I need to adjust naming for these MMIO calls)
* Implement read/write MC. (so many hardcoded oneoffs AMD)
* Implement write32PLLAtMask MMIO call
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42146 a95241bf-73f2-0310-859d-f6bbb57e9c96
into it again (adding generic CBI support). It is so much of a copy even that it
still claimed to have the original 3 support descriptors while in fact it only
has one. Since the memory beyond that one support descriptor was probably just
zeros, making them complete wildcards usb_support_descriptor wise, this lead to
every single USB device being handed to the usb_floppy device added hook.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42145 a95241bf-73f2-0310-859d-f6bbb57e9c96
partition_module_info::uninitialize().
* Implemented the hook for BFS.
* Implemented KFileSystem::Uninitialize().
Fixes failure to initialize a BFS initialized device with an intel partition
map.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42142 a95241bf-73f2-0310-859d-f6bbb57e9c96
destroy the partitioning system's on-disk structure.
* Adjusted the existing partitioning system implementations accordingly.
Actually implemented the hook for the intel partitioning system.
* Added Uninitialize() method to KDiskSystem and KPartitioningSystem. The latter
implements the method calling the new module hook.
* _user_uninitialize_partition(): Also let the disk system uninitialize the
on-disk structure.
This fixes the failure to initialize a disk device with BFS, when it contains a
valid partition map with at least one partition.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42140 a95241bf-73f2-0310-859d-f6bbb57e9c96
which don't wait for a character, but return -1 when no character is
available ATM. Implemented correctly for x86 only.
* Changed the semantics of the debugger_module_info::debugger_getchar() hook.
It is supposed to return immediately now.
* Adjusted usb_keyboard accordingly. Hacked UHCI's debug_process_transfer() to
achieve that. It does now start, check, or cancel a transfer. Split
UHCI::ProcessDebugTransfer() into StartDebugTransfer(), and
CheckDebugTransfer() accordingly, and also added a CancelDebugTransfer().
The latter seems to have issues. Michael, please have a look. I have no clue
what I'm doing. :-)
* Adjusted kgetc() to poll all possible inputs using the new
functions/semantics. This allows to use any input (USB, PS/2, serial) in KDL.
* Removed the no longer needed "serial_input" command.
* read_line(): Also support 0x7f as backspace code. That's what xterm sends.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42126 a95241bf-73f2-0310-859d-f6bbb57e9c96
* Would be nice to only show this when an extra argument had been passed to
checkfs, but I'm afraid the API is somewhat limited, not to say pretty much
unusable for the task.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42125 a95241bf-73f2-0310-859d-f6bbb57e9c96
* Reorganized the kernel locking related to threads and teams.
* We now discriminate correctly between process and thread signals. Signal
handlers have been moved to teams. Fixes#5679.
* Implemented real-time signal support, including signal queuing, SA_SIGINFO
support, sigqueue(), sigwaitinfo(), sigtimedwait(), waitid(), and the addition
of the real-time signal range. Closes#1935 and #2695.
* Gave SIGBUS a separate signal number. Fixes#6704.
* Implemented <time.h> clock and timer support, and fixed/completed alarm() and
[set]itimer(). Closes#5682.
* Implemented support for thread cancellation. Closes#5686.
* Moved send_signal() from <signal.h> to <OS.h>. Fixes#7554.
* Lots over smaller more or less related changes.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42116 a95241bf-73f2-0310-859d-f6bbb57e9c96
problems on various systems. Resolves#3441. Thanks!
+alpha3
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42104 a95241bf-73f2-0310-859d-f6bbb57e9c96
AcquireReference() now does, and adjust all callers that relied on the previous
return type.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42091 a95241bf-73f2-0310-859d-f6bbb57e9c96
only halfway finished. The way it is supposed to work is that there are two
tty cookies, representing the system and the device side. Reads and writes
coming from the system and going to the device are using the system cookie
while reads and writes coming from the device use the device cookie.
* Move writing to the device into an output thread, similar to how reading from
the device works. This isn't necessarily a good idea and might be moved back
into the write hook again to ensure that writes can be made blocking. Right
now if you just write and then close, the writes will most likely be canceled
before every going out to the device.
* Removed the read and write lock mutex. They aren't necessary as the tty layer
will serialize the reads and writes anyway.
* Made simply copying the data to the write buffer the default implementation of
the OnWrite callback and removed the OnWrite in ACMDevice. The ProlificDevice
didn't provide an OnWrite hook before, so it would've never written anything.
* Break out the baud index to speed mapping into an inline function. Since the
defines might change in termios.h just adding an array is a bit fragile (it
already missed one entry and would've been broken for certain speeds).
This should make usb_serial usable for some (most?) cases. I've tested this with
an Arduino board that uses an FTDI interface. As mentioned above, since writes
currently just write into the tty layer and don't wait for the data to be
flushed, and since close doesn't wait for the output buffers to be drained
either, a simple write and close (as in "echo a > /dev/ports/usb0") will in most
cases cancel the output before it is written to the device. I'm looking into
a few ways to fix that next.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42089 a95241bf-73f2-0310-859d-f6bbb57e9c96
header is used that only has 6 bits of length info this would've previously
potentially overflowed depending on the input size.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42088 a95241bf-73f2-0310-859d-f6bbb57e9c96
is inside the cflags) since stty for example sets them.
* Turn off debug output by default and fix a warning due to that.
* Some minor cleanup.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42087 a95241bf-73f2-0310-859d-f6bbb57e9c96
* Begin using multi-architecture friendly formatting macros per ML
* Change uint32 snoozeTime to preferred bigtime_t per ML
* Thanks for the great feedback!
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42062 a95241bf-73f2-0310-859d-f6bbb57e9c96
* add additional tracing to usb_disk lun inquiry
* cd and other optical disk devices can take some time to spin up
when plugged. Now we give them some time to do so to ensure we
can detect the media type properly if there is a cd in the drive.
Things non-mechanical (flash drives) will continue almost immediately
as there is no spin up time. The more attempts, the longer the wait.
We now try 7 times (28 seconds total), my modern usb cdrom takes
about 6 (21 seconds) of those cycles to be ready on power up and 4
(10 seconds) on media change while powered up.
* tested with usb media and cd media. Doesn't introduce any visible
delay to the user.
* the write protected status in lun is now correct for my usb cd device
on plug (it wasn't previously)
* still seeing it though as read/write. Looking at this now.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42058 a95241bf-73f2-0310-859d-f6bbb57e9c96
* Made MessageIO comply to our coding style.
* No other functional change (intended).
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42055 a95241bf-73f2-0310-859d-f6bbb57e9c96
always calling the device and requesting it. If no HID descriptor is found in
the configuration we fall back to retrieving it manually and if that fails we
fall back to a dummy report descriptor length. In the most usual case this will
save one unnecessary USB control request.
Incidentally this also fixes the absolute pointing device under VirtualBox. VBox
stalled the retrieval of the HID descriptor. That alone wasn't so problematic as
in this case we just fell back to the dummy report descriptor length which
would've been large enough. But VBox also times out the next request after the
stall, which in this case was the retrieval of the report descriptor, hence no
HIDDevice could be created.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42019 a95241bf-73f2-0310-859d-f6bbb57e9c96
* As they don't claim to be HID, they don't provide a report descriptor either,
so we build one. The built descriptor is similar to the one found in FreeBSD
for the same class of devices. Might fix/help #7649, for lack of hardware I
can't test this.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42003 a95241bf-73f2-0310-859d-f6bbb57e9c96
usb_hid_device_added hook so that we can actually detect non-HID devices at all.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42002 a95241bf-73f2-0310-859d-f6bbb57e9c96
allow for creating descriptors that don't use report IDs at all.
* Adjust sixaxis_build_descriptor and set the global report ID once at the
beginning instead.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42001 a95241bf-73f2-0310-859d-f6bbb57e9c96
* Add these to the usb_support_descriptor when adding from the quirky devices.
* Extend the SIXAXIS comment a bit.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42000 a95241bf-73f2-0310-859d-f6bbb57e9c96
descriptor. This allows us to support devices that aren't strictly HID or only
provide vendor specific interfaces by constructing report descriptors for their
data format.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@41992 a95241bf-73f2-0310-859d-f6bbb57e9c96
absolute coordinates (qemu/kvm -usbdevice tablet) and various digitizers. If a
tablet-like usage is determined the MouseProtocolHandler publishes to
input/tablet instead of input/mouse and reports its info in a tablet_movement
structure instead of a mouse_movement structure, allowing for absolute
coordinates. Note that right now only the absolute coordinates are used, the
other tablet specific inputs (eraser, pressure, tilt and contact) aren't yet
filled in. I will add these as a second step.
I've only tested this with kvm where this makes the "seamless" mouse integration
work and therefore fixes#5989. Note that QEMU for BeOS/Haiku doesn't support
that mode (patch pending on my side) and will lock the pointer into the upper
left corner if -usbdevice tablet is used (whereas it previously just did
nothing).
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@41951 a95241bf-73f2-0310-859d-f6bbb57e9c96
