errors for narrow transfers after a reselect. FreeBSD sym driver has a comment
about this, but their workaround (disable SCSI gross error reports) doesn't
work for me. Instead dissallow disconnect if the target is not wide
(FreeBSD doens't allow disconnect until the target has been fully probed, which
is why they may not have noticed my problem).
particular, make sure that all the SIASTAT_ANS bits are in the right state
so we don't do something inane.
Still doesn't actually bring the link up properly, but at least it negotiates
most of the time, and does it a little faster.
1) Do not call tlp_sia_update_link() in Nway mode, and do not look at SIASTAT
in any other place that nway_status(), where we first check that it's valid.
In other places, look at IFM_ACTIVE after having call nway_status().
2) Eliminate stupid MII_MEDIACHG calls, and arrange for nway_service() to
update status on every call.
3) Nuke the synchronous case of nway_auto() from orbit.
4) Do not call nway_statchg() when using manual configuration; tlp_sia_set()
does everything we need.
1) Set OPMODE_TTM in the default tsti_opmode, so that nway_status doesn't
blow up and report the wrong media type when statically configured. (This
code is a hack.)
2) Do not set IFM_ACTIVE (i.e. ignore SIASTAT_LS*) when in auto-negotiation
mode and negotiation has not completed (per 21143 manual).
3) Do not clear auto-negotiation mode; otherwise the chip will not
renegotiate on a link failure.
With these changes, 10/100 selection is more stable, and auto-negotiation
comes up with the right status and detects link, but the link does not work
unless it's hardwired. More work is needed.
It is unclear if this realy is needed and if, on which type of cards. I
haven't run accross a card that needs it yet. This may have been just
a copy & pasto from the ISAC interrupt handler carried over to IPAC.
Remove the clear-the-irq-after-enabling it dance (which had bad side
effects on some cards). Instead disble the ISAC receiver when we have
interrupts disabled. Adjust the interrupt handler to properly deal with
subtle differences of the ISAC implementation in IPAC chips.
if error occurs after status is collected) race condition
when using the status byte to detect completed commands (a command descriptor
could be recycled before the device disconnected), and make the
interrupt routine handling completed commands more efficient (no need to
scan target * lun * tag array any more).
there may be tagged commands still running when we queue a request sense
command.
Solve this by using 2 DSA entry per LUN
- Now that we have the command DSA before select, we can load T/L/Q in
SCRATCHC. This makes the selection timeout handler simpler.
- Avoid a race condition when setting the free flag in the cmd ring (see
comment in the script)
- don't forget to update the ID in the head of LUN table after a sync/wide
negotiation. This fixes the command timeout at the first data command
after negotiation (the bus reset handler did update the ID properly,
so subsequent commands were OK).
- for DMA interrupts, clear fifo if it's not empty. Leaving the fifo dirty
would prevent subsequent interrupts from coming in.
- Various improvements in debug messages
- misc cleanups.
scheduler slot. This costs a few more instructions but divide the size of the
scheduler ring by 2, saving 1k of onboard RAM (a bus with 15 devices would
overflow the on-board RAM by 128 bytes).
- Add support for DT transfers (aka Ultra/160) in esiop
Note that DT transfers are not enabled for 53c1010-33 rev 0 yet; if I trust
FreeBSD it has a bug which prevent them to do DT properly.
From the same source there may be issues with some revs of 53c1010-66.
taken from OpenBSD. Test hardware kindly provided by Intel. This still needs
management bits, and doesn't support older controllers, but that shouldn't
be hard to fix.
For this add another indirecton: the DSA in the LUN table points to
a table of DSA indexed by the tag number when tagged command is in use.
For non tagged command, the LUN DSA still points to the tables describing the
xfer directly.
yet.
If is restricted to SIOP which implement the load/store instruction, and
has 10 scratch registers (basically, 825 and newer, possibly 770).
It implements a different interface between host and script, using a real
ring for command starts, and improved support for reconnect which will allow
256 tag per device. It uses interrupt on the fly to signal complete command,
which allows several commands to be serviced per interrupt and doesn't require
the script to stop to signal command completion.
3 bits are lun address modifiers.
Remove code that (incorrectly) thought it was asking the f/w to only
PLOGI if not already PLOGI'd. The current f/w documentation tells us
that we have this backwards.
"true" at the appropriate times for non-PCMCIA interfaces. This
means that the ENETRESET path in cs_ioctl() now runs, thus fixing
multicast (and IPv6) on my Shark. Yay.
* Simplify cs_hash_index(): Rather than taking the bottom 6 bits of
a big-endian CRC32 and reversing them, just take the top 6 bits of
a little-endian CRC32.
WI_RID_SCAN_APS in previous commit works for Intel Pro/Wirelss 2011
with firmware 2.51.1.
It seems that the firmware automatically updated after the card runs on
Windows 2000 with 2011_2011B_CD_3.0 in Intel web site.
The card is Type 1 CF card and it doesn't have firmware in.
So we need to download the firmware image into the card before
touching it.
XXX downloading code should be written in generic (bus independent),
but I don't have enough information for now.
bouyer