Fixes broken blitting from rcons.
* Put back old 4.4bsd range test on cursor movement. 1.2 code is broken.
* Disable screensaver, it reportedly never comes back on properly.
needed. When sfbattach() initializes the fbinfo data, it was corrupting
data past the struct device data actually allocated. This does not appear
to have caused a problem in the past, but causes a problem with the new
setroot() changes by Jason.
Where CACHED_TO_HYS() is still needed for kernel-virtual-to-physical
or physical-to-uncached mapping (fb drivers), replace with
`#include <mips/cpuregs.h>'.
* dcparam() with normal tty t_param interface, which calls
* cold_dcparam() called with explicit dc7085 register address
and flags, which does the work and is also callable when cold,
to set up console (or kgdb) line parameters.
DEC dc503 cursor chip) into Decstation 2100,3100 cfattach front-end
and ``machine-independent'' back-end.
pm_ds.c: pmin/pmax cfattach front-end
pm.c: bt478, 503 back-end
pmvar.h: declarations of back-end normal and console attach
entry points.
use the pre-autoconfig cold serial-console inititialization entry
points from the bus-specific cfattach front-end code.
* Delete post-autoconfig code to switch from PROM output to kernel
driver for machines with dc serial chips.
cfattach front-end code:
dc_ds for the decstation 2100( pmin), 3100 (pmax), and 5100.
dc_ioasic for the decstation 5000/200 (3max) which does not have a
DEC TC-style IOCTL asic, but is configured as if it did.
* Add pre-autoconfig code initialization of kerenl dc driver console I/O
for remote serial consoles. The hack to use PROM serial I/O until the
dc device is autoconfigured is no longer necessary.
serial consoles to the 1.2 branch. Includes:
* dynamically allocated new-config softc
* remove dependencies on Decstation CPU type, use flags in softc instead.
* pass in values for softc flags (q.v.) from parent-specific attach code
* #ifdef out rts/cts flow control support until it's known to work on
200s.
* redo initialization of serial consoles (needs more work).
The Lite2 changes include:
* Remove the last vestiges of high-bit-set-means-delay for output chars.
* Handle the 2100/3100 having partial modem control on line 2 only,
whereas the 5000/200 has modem control signals on lines 2 and 3.
* Add RTS/CTS support for lines 2 and 3 on a 5000/200.
* Add more s = spltty(); splx(s); where needed but not present.
as a console, initalize as white-on-black so console messages are legible.
(Sean Davidson reports that rcons still messes up the display, perhaps
due to using the wrong pixel depth).
1. Start at the specified entry instead of entry 0.
2. Use the blue value instead of the green when setting the blue color entry.
3. Don't use the starting index again for storing the saved entry - the cmap
pointer was previously initialized using the starting index. This fixes
a hard hang on the maxine when console output is done after calls to
set the color map (usually by the X server).
* Add interrupt handler for 3MIN, where we cannot disable TC slot interrupts.
* Change mfbinit() signature to match other (pmax) TC framebuffer init
routines.
* TODO after 1.2: add {cfb,mbf,sfb}var.h. Declare init functions there.
message-in. The remaining transfer count restored when a device is
reselected needs to be saved. The saved value is needed to compute
the number of bytes transferred if another disconnect occurs. This
fixes a random read data corruption that occurs on certain disks that
may disconnect more than once in the middle of a DMA transfer.
Show proper inquiry data when version >= 1, not <= 1 (SCSI-2 devices
now display their inquiry infor).
Correct transfer length passed to dk_unbusy (b_resid hasn't been
updated yet).
configure properly. Also fix devices with TurboChannel and mainbus
attachments so they will work if no TurboChannel was configured.
Fix clock.c for a missing variable if not including NTP support.
Also remove some extraneous includes files or use the right ones.
configure properly. Also fix devices with TurboChannel and mainbus
attachments so they will work if no TurboChannel was configured.
Fix a panic when the dtop keyboard handler receieves a character
before the device has been opened.
update the 4.3bsd/Ultrix-compatible qvss-style mmap'ed framebuffer/input-event
code to use mips_round_page() et.al., not pmax_round_page().
Add explicit "int" return types to functions. Add prototyped forward
declarations.
Fix the the definitions of dtop cdevsw entry point functions to match
their declarations. Add explicit "int" declarations to functions.
Add prototyped declarations for all local functions.
Return zero from dtopstop().
Include the external declarations from dtopvar.h.
Add prototypes to (most of) src/sys/arch/pmax/pmax. (The un-protytyped
parts still have pending merges with the Pica port.)
Fix splx() glitches in pmax/clock.c.
Delete old cpu/fpu identification from pmax/autoconf.c, use r4400/r4600/idt
aware code from Pica port, now in mips/mips/mips_machdep.c.
Delete unused multi-CPU autoconfiguration code; NetBSD/pmax does not
support decsystem 5800s anyway.
Update the pmax SCSI drivers (rz and tz) to use <machine/conf.h>.
Fix the driver entry points to have the correct signatures -- add
"ioflag" args to read() and write(), add "struct proc *p" arg to
open and close.
Stop using __BDEVSW_DUMP_OLD_TYPE, and update the rzdump and tzdump
entry points to have the correct, MI signatures.
NB: this is just syntactic sugar: both the caller and the dump entry
points ignore the additional args, and do exactly what they did before.
This must be fixed before using dump entry points in non-pmax drivers
(e.g., the MI scsi code).
add prototyped declarations for the callbacks which add old-style
(4.4bsd/pmax conf.old) SCSI controllers, and which configure SCSI slaves
on such controllers.
rewriting the SII driver to work with the MI scsi would be a better option,
if time were available, and the MI scsi code supported SCSI controllers with
an 8k upper bound on transfers.
Add prototyped declarations for scsiGroup0Cmd and scsiGroup1Cmd.
Add prototype declarations for scsiPrintSense. Cut the inqiury-response
pretty-printer from tz.c and rz.c and paste it in as scsiPrintInquiry.
-Wall -Wmissing-prototypes:
Add prototypes.
Fix printf() format strings (%x vs pointer-arg, %x with a long int).
Fix a possibly-uninitialized shadowing local variable "resid" in tzdone().
include <sys/systm.h> to get prototypes for printf() and bcopy().
- split softc size and match/attach out from cfdriver into
a new struct cfattach.
- new "attach" directive for files.*. May specify the name of
the cfattach structure, so that devices may be easily attached
to parents with different autoconfiguration semantics.
based on "#ifdef MELLON": examine the framebuffer dimensions in the
fb softc, and initialize the x-axis offset appropriately.
User-level changes to (e.g.) an Xserver are still needed to work
on an SFB.
The dtop driver no longer requires the "needs-count" flag.
Fix a panic in boot-time interrupt establish. The "generic" pmax
interrupt-establish code assumes that all interrupt args are new-config
device structs accessed via a struct cfdriver. Make it so.
independent TC support in sys/dev/tc/tc.c and sys/dev/tc/tcvar.h:
* Change the tc autoconfiguration tables to use a struct tc_attach_args
instead of the ad-hoc structure.
* Change all pmax device drivers to use a `struct confargs' that's
assignment-compatible with sys/dev/tc/tcvar.h `struct tcdev_attach_args'.
Devices that can be present on a TC or as ioctl asic/mainbus builtins
use the same `struct confargs'.
* Eliminate the `BUS_CVTADDR()' macros which the pmax port inherited from
an old, now-obsolete sys/arch/alpha snapshot.
* Update the comments and debugging code in interrupt handlers to
be consistent with the machine-independent TC support.
Other commits that overlap the same source files include: re-enabling
clock-tick interrupts earlier, and counting hardclock ticks for vmstat -i.
independent TC support in sys/dev/tc/tc.c and sys/dev/tc/tcvar.h:
* Change the tc autoconfiguration tables to use a struct tc_attach_args
instead of the ad-hoc structure.
* Change all pmax device drivers to use a `struct confargs' that's
assignment-compatible with sys/dev/tc/tcvar.h `struct tcdev_attach_args'.
Devices that can be present on a TC or as ioctl asic/mainbus builtins
use the same `struct confargs'.
* Eliminate the `BUS_CVTADDR()' macros which the pmax port inherited from
an old, now-obsolete sys/arch/alpha snapshot.
* Update the comments and debugging code in interrupt handlers to
be consistent with the machine-independent TC support.
Other commits that overlap the same source files include: re-enabling
clock-tick interrupts earlier, and counting hardclock ticks for vmstat -i.
- New metrics handling. Metrics are now kept in the new
`struct disk'. Busy time is now stored as a timeval, and
transfer count in bytes.
- Storage for disklabels is now dynamically allocated, so that
the size of the disk structure is not machine-dependent.
- Several new functions for attaching and detaching disks, and
handling metrics calculation.
Old-style instrumentation is still supported in drivers that did it before.
However, old-style instrumentation is being deprecated, and will go away
once the userland utilities are updated for the new framework.
For usage and architectural details, see the forthcoming disk(9) manual
page.
Eliminate pmax/tc/tc.h. Use dev/tc headers for pmax port. Change pmax TC
autoconfig tables to use structs (mostly) compatible with dev/tc/tcvar.h.
Move TC console search to tc.c.
jonathan