* The function speed(), imported from 4.4BSD-Lite2, has never been
used by NetBSD. Obtained from FreeBSD.
* Finish removing -L (litout) option. This has not been supported
since rev. 1.5 (NetBSD 1.0). The option still appeared in the
usage and man page. Obtained from FreeBSD.
* In function doit(), dead code imported from 4.4BSD-Lite2, dealing
with termios. NetBSD cracked this nut differently long before this
import. Obtained from FreeBSD.
bit in the SROM. It seems as if it is set to 1 when the PHY is
*analog*, not *digital*. Fix my sources.
In rtw_intr_rx, use units of 500kb/s instead of 100kb/s for rate,
to be consistent with net80211's expectations. Polish up some
debugging ugly messages. Dump raw 802.11 packets if IFF_DEBUG|IFF_LINK2
and RTW_DEBUG is defined.
Polish power-state (on/sleep/off) handling. Especially improve
support for RFMD (totally untested) and Maxim. For Philips, take
the Digital PHY property into account.
Call the net80211 watchdog function from rtw_watchdog, so that we
scan again if auth/assoc fails.
Be a little more cautious about writing register[RTW_TPPOLL], since
other drivers are.... Don't frob the high/low-priority queues
right now, since I don't use them.
Add rtw_join_bss which programs the card with the BSSID and other
properties of a BSS. Use it on state transitions. Factor out
rtw_set_nettype.
Make rtw_recv_beacon call ieee80211_recv_mgmt instead of dropping
beacons on the floor! TBD IBSS merges.
Change some rtw_debug=2 printfs to rtw_debug=3 (RTW_DPRINTF3)
printfs so the console doesn't get spammed so badly at rtw_debug=2.
Change some debugging printfs to RTW_DPRINTFs. E.g., print the
"RF programming method" only if debugging is enabled.
Protect SIOCG80211STATS with splnet()/splx() so that it takes a
"snapshot" of the 802.11 statistics, which is superfluous if
ieee80211_ioctl is always called at splnet()....
Instead of extending fsinfo_t it now holds a void * to file system specific
data. This is then setup/cleaned up by the additional of 2 additional
callbacks. Makes adding new filesystems simpler as almost no code has
to be updated in the generic makefs code now.
> revision 1.2.2.1
> date: 2004/12/17 02:51:35; author: brad; state: Exp; lines: +2 -2
> MFC:
> Fix by frantzen@
>
> &&/|| inversion would try to merge IP addresses with non-addresses into a
> single table causing a ruleset load error and eventually a double-free.
>
> ok deraadt@ mcbride@ henning@ frantzen@ dhartmei@
descriptor rings, move packets from the transmit queues to the
transmit rings, handle transmission-completed interrupts. My
Linksys WPC11 ver. 4 with Maxim RF, generates interrupts like it
is successfully transmitting packets. Clearly there are bugs: my
G4 Powerbook locks up hard. I will debug tomorrow.
For use by the subroutine ieee80211_compute_duration, add struct
ieee80211_duration, and #define a number of microsecond constants
used for the transmit timing of 802.11 packets.
Add the subroutine ieee80211_compute_duration, which computes for
any packet the appropriate 802.11 Duration field, the PLCP Length
field, as well as the Duration and Length fields for an RTS frame.
atw(4), rtw(4), future drivers, and possibly ath(4) will share
ieee80211_compute_duration.
header files, so that they don't become out of sync (again).
- Use bitmask_snprintf() instead of hand-rolled code.
- Always check array bounds before dereferencing print arrays.
- Order arguments in the vnode printing functions consistently.
Connect over tcp on the loopback is broken:
4729 amq 0.000007 CALL connect(4,0x804f2a0,0x1c)
4729 amq 75.007420 RET connect -1 errno 60 Connection timed out
ginsbach