This is based on amiga's siop driver, but converted to use
bus_space(9) functions and modified to fit bus_dma(9) framework.
Currently tested on NetBSD/arc with jazzio 53c710 SCSI,
which really requires bus_dma(9) functions :-)
Sync transfers and disconnect/reconnect are also working.
TODO:
- Test under more heavy load
- Clean up osiop_checkintr() hander
- Reorganize command queue and sync negotiation handling more suitable
for thorpej-scsipi mid-layer
- Re-think defered interrupt handling for amiga
based on the existing net/if_spppsubr.c stuff.
While there are completely userland (bpf based) implementations available,
those have a vastly larger per packet overhead thus causing major CPU
overhead and higher latency. On an i386 base router, running a 486DX at 50MHz
my line (768kBit/s downstream) was limited to something (varying) between 10
and 20 kByte/s effective download rate. With this implementation I get full
bandwidth (~85kByte/s).
This is client side only. Arguably the right way to add full PPPoE support
(including server side) would be a variation of the ppp line discipline and
appropriate modifications to pppd. I promise every help I can give to anyone
doing that - but I needed this realy fast. Besids, on low memory NAT boxes
with typically a single PPPoE connection, this implementation is more
lightweight than a pppd based one, which nicely fits my needs.
This now provides slightly more functionality than the FreeBSD layer1-newbus
interface. It was meant to be a simple change to one header and a few
c files, but the change rippled all through various stuff.
To prevent a change to the kernel<->userland interface right now the kernel
is now lying about card types to userland (but who cares). This will be fixed
when the userland interface changes, after layer 3 <-> layer 4 has been
fixed.
Functional changes:
Provide a clean interface for hardware drivers to attach to the upper
layers. This will need another small change in the B-channel handling
when a similar change to the layer 3 <-> layer 4 interface happens.
Avoid passing indices into global arrays of pointers around, instead pass
the pointers itself. Don't code hardware driver types by predefined magic
numbers (think LKM). Prepare for detachable drivers (think pcmcia).
While there remove some sets of function pointers always pointing to the
same function (meant to be the configurable set of D channel protocol
handlers). It is unlikely another supported D-channel protocol will fit into
that (maximal layer interface) abstraction. When we get support for another
protocol, we will need to come up with a workable interface. Besides, the
old implementation was, uhm, strange.
including layer_*.c if "options LKM". This is not the right way to fix
it, but we have as yet no standardized mechanism to add a "LKM code
library" to fill in gaps in the monolithic kernel's code.
Problem noted by <tron@netbsd.org>.
This is the kernel part (userland to follow soon) of the latest (and
very probably last) release (version 0.96) of ISDN4BSD. ISDN4BSD has a
homepage at http://www.freebsd-support.de/i4b/.
It gives the user various ways to use the isdn connection: raw data (via
the i4brbch "raw b-channel" device), ppp (via the isp "isdn PPP" device),
voice/answering machine (the i4btel "telephone" device) and ip over isdn
(the ipr device, "IP over raw ISDN").
Supported are a bunch of common and older cards, more to be added soon
after some cleanup. Currently only the european E-DSS1 variant of the
ISDN D channel protocol is supported.
This is very adhoc work for IETF meeting.
- Since it seems that 'an' and 'wi' have similar hardware, low level
functions should be shared.
- There are PCI/ISA cards of Aironet but not supported yet.
- The wiconfig interface is changed so that wiconfig cannot be used.
- 'ancontrol' of FreeBSD is not ported.
- Only infrastructure mode is tested.
- WEP is not supported.
Though I only have an Aironet card, Cisco card should be expected to work.
Current status:
Only OHCI chip is supported (fwohci).
ping (IPv4) works with Sony's implementation (SmartConnect) on Win98.
sometimes works but not stable.
Not implemented yet:
IRM (Isochronous Resource Manager) functionality.
Link layer fragmentation.
Topology map.
More to do:
clean ups
MCAP
charactor device part
dhcp
There is no entry in GENERIC config file yet.
Follow sys/dev/ieee1394/IMPLEMENTATION to enable if_fw.
when running at splserial(). This is a temporary measure (until
there's a MP-safe interrupt handling structure); until then, it should
be used when MULTIPROCESSOR and IPL_SERIAL > IPL_SCHED.
that required to support NFSv2 mounts. Not finished yet, but already
provides some 44k of saving in code size on arm26. More savings, and some
documentation, are still to come.
and a front-end driver for the Ether3. Only semantic change is to remove
ea_claimirq() and ea_releaseirq() on the grounds that the seem too spurious
to warrant a callback to the front-end.
as used on later arm26 system (A5000, A4, A3010, A3020, A4000).
What we have got:
...
upc0 at iobus0 base 0x010000: config state bb 87 1c 00 00
fdc at upc0 offset 0x3f4 not configured
wdc0 at upc0 offset 0x1f0
lpt0 at upc0 offset 0x278
com0 at upc0 offset 0x3f8: ns8250 or ns16450, no fifo
...
What we haven't got:
- FDC support (found, but not configured).
- Clearing lpt interrupts on arm26 systems (needs help from IOEB).
- A upc(4) manual page.
- More than minimal testing (my A3020s don't have root devices).
- A proper probe routine (arm26 can't use one anyway).
break character with the supplied one. This is useful for cases where
break is hard to generate, or you are connected to a PC that "sends"
breaks when power cycled. For this mode in com, interpret break char
in the polling section, which allows entry into the debugger before
the tty is opened. Only supported in the com driver currently.
arc4 implementation by Kalle Kaukonen has been added.
define "wlan" in files.
XXX: only awi depends on wlan for now.
Allow authentication for adhoc (IBSS) mode.
Disable adhoc mode without bssid (mediaopt adhoc,flag0) for FH radio.
FH cannot work without synchronization by beacons.
Align IP header for ethernet encapsulation (IFF_FLAG0) mode.
Print available access points for IFF_DEBUG.
such as the LM78 and VT82C686A (and eventually ACPI). Multiple
sensor devices can be hooked registered with `sysmon', and eventually
sysmon will also handle hardware (and software) watchdog timers.
Convert the `lm' and `viaenv' drivers to the new interface.
- use latest source address selection code - in6_src.c.
- correct frag header insertion.
- deep copy ip6 header portion in ip6_mloopback to avoid overwrite.
- do not bark when we forward packet to loopback.
- some cosmetics.
This work is based on code written by Scott D. Telford, the IBM
Token Ring card attachment was written by Gregory McGarry.
XXX this is still very experimental and development version; use at your
XXX own risk
(the name 'siop' is still being discussed, may change).
Only basic disconnect/reselect for now, no sync/wide negotiation.
Tested with 810A, 875 and 895 on i386 only.
The bus-independant part should also be able to handle the 53c720 and 53c770.
A new driver with enhanced script should appear for the 825/875/895 'soon'.
to be called `rl' and it conflict with RL vax disks, canonical and
historical unix driver name.
This changes are minimal: it only changes the name of RealTek driver.
The filename of source code and a lot of the letter `rl' in source
files should be changed shortly.
to protocol handlers, based on src/dst (for ip proto #4/41).
see comment in ip_encap.c for details of the problem we have.
there are too many protocol specs for ip proto #4/41.
backward compatibility with MROUTING case is now provided in ip_encap.c.
fix ipip to work with gif (using ip_encap.c). sorry for breakage.
gif now uses ip_encap.c.
introduce stf pseudo interface (implements 6to4, another IPv6-over-IPv4 code
with ip proto #41).
amount of physical memory, divide it by 4, and then allow machine
dependent code to place upper and lower bounds on the size. Export
the computed value to userspace via the new "vm.nkmempages" sysctl.
NKMEMCLUSTERS is now deprecated and will generate an error if you
attempt to use it. The new option, should you choose to use it,
is called NKMEMPAGES, and two new options NKMEMPAGES_MIN and
NKMEMPAGES_MAX allow the user to configure the bounds in the kernel
config file.
- interop issues in ipcomp is fixed
- padding type (after ESP) is configurable
- key database memory management (need more fixes)
- policy specification is revisited
XXX m->m_pkthdr.rcvif is still overloaded - hope to fix it soon
due to massive changes in KAME side.
- IPv6 output goes through nd6_output
- faith can capture IPv4 packets as well - you can run IPv4-to-IPv6 translator
using heavily modified DNS servers
- per-interface statistics (required for IPv6 MIB)
- interface autoconfig is revisited
- udp input handling has a big change for mapped address support.
- introduce in4_cksum() for non-overwriting checksumming
- introduce m_pulldown()
- neighbor discovery cleanups/improvements
- netinet/in.h strictly conforms to RFC2553 (no extra defs visible to userland)
- IFA_STATS is fixed a bit (not tested)
- and more more more.
TODO:
- cleanup os-independency #ifdef
- avoid rcvif dual use (for IPsec) to help ifdetach
(sorry for jumbo commit, I can't separate this any more...)
tsutsui