Notes:
- I added bsd.obj.mk and made it work with objdirs.
- I added an entry point to the linker to fix a warning.
- I made the backup of biostramp.inc silent.
- I added missing clean targets.
This needs to be tested further.
tape when a volume is full, and try to reopen the tape drive for 2 mn.
To be used with tape changers which load the next tape when the current one is
ejected.
While I'm there fix eject handling for remote tape.
by allowing the hardware drivers to register keyboard and display
support with the ite framework. Removes the dependence on the hil
keyboard and should make support for dnkbd easier.
An interim fix until wscons arrives.
if the vec pointer is valid rather than using uvm_useracc().
uvm_useracc() just tells you if the permissions of a user mapping allow
the desired access, not whether faulting on that mapping will succeed.
the response queue. Instead of the ad hoc ISP_SWIZZLE_REQUEST, we now have
a complete set of inline functions in isp_inline.h. Each platform is
responsible for providing just one of a set of ISP_IOX_{GET,PUT}{8,16,32}
macros.
The reason this needs to be done is that we need to have a single set of
functions that will work correctly on multiple architectures for both little
and big endian machines. It also needs to work correctly in the case that
we have the request or response queues in memory that has to be treated
specially (e.g., have ddi_dma_sync called on it for Solaris after we update
it or before we read from it).
One thing that falls out of this is that we no longer build requests in the
request queue itself. Instead, we build the request locally (e.g., on the
stack) and then as part of the swizzling operation, copy it to the request
queue entry we've allocated. I thought long and hard about whether this was
too expensive a change to make as it in a lot of cases requires an extra
copy. On balance, the flexbility is worth it. With any luck, the entry that
we build locally stays in a processor writeback cache (after all, it's only
64 bytes) so that the cost of actually flushing it to the memory area that is
the shared queue with the PCI device is not all that expensive. We may examine
this again and try to get clever in the future to try and avoid copies.
Another change that falls out of this is that MEMORYBARRIER should be taken
a lot more seriously. The macro ISP_ADD_REQUEST does a MEMORYBARRIER on the
entry being added. But there had been many other places this had been missing.
It's now very important that it be done.
For NetBSD, it does a ddi_dmamap_sync as appropriate. This gets us out of
the explicit ddi_dmamap_sync on the whole response queue that we did for SBus
cards at each interrupt.
Set things up so that platforms that cannot have an SBus don't get a lot of
the SBus code checks (dead coded out).
Additional changes:
Fix a longstanding buglet of sorts. When we get an entry via isp_getrqentry,
the iptr value that gets returned is the value we intend to eventually plug
into the ISP registers as the entry *one past* the last one we've written-
*not* the current entry we're updating. All along we've been calling sync
functions on the wrong index value. Argh. The 'fix' here is to rename all
'iptr' variables as 'nxti' to remember that this is the 'next' pointer-
not the current pointer.
Devote a single bit to mboxbsy- and set aside bits for output mbox registers
that we need to pick up- we can have at least one command which does not
have any defined output registers (MBOX_EXECUTE_FIRMWARE).
Explicitly decode GetAllNext SNS Response back *as* a GetAllNext response.
Otherwise, we won't unswizzle it correctly.
Nuke some additional __P macros.
overriding FD_SETSIZE. Not overriding it makes it stomp all over memory
(which caused the debug outputs we've seen lately).
It used to work, but toolification of lint broke it.
