2 times in the past
- Set up timeout per xfer instead of per interrupt. This helps with
PIO transfer (we would call timeout()/untimout() several times for a
transfer).
- If we missed an interrupt for a PIO transfer, reset and restart it
immedialy, don't try to recover and continue. If we missed an interrupt we
may have lost a read/write cycle on the IDE bus. If this happens 1) we
corrupt data and 2) we enter an interrupt loop at the end of the xfer, as
the drive has some more data to read/write, but the host thinks the xfer is
done.
This last change fix the (or at last some of the) 'lookup after lost interrupt'
some peoples have been experiencing.
are called from the interrupt or timeout handler, 0 otherwise.
- use this to know if we can busy-wait for wait_for_unbusy or wait_for_ready
This fixes a bug where CDs withot the DRQ_INTR capability would not busy-wait
for the CMDOUT phase.
While I'm there change 2 delay() to DELAY() for consistency, and
garbage-collect some old code from wdcintr() which has been ifdef'd out
for some time now.
DRIVE_OLD, DRIVE_ATA or DRIVE_ATAPI based on register signatures.
The attach routine will issue a IDENTIFY command for ATA/ATAPI disk,
to detect flase matches by the probe routine.
probe/attach should now be fully compliant with ata-4/ata-5. As a side
effect, ATAPI drives which improperly use ATA register signatures should now
be attached as ATAPI.
need to downgrade, downgrade to PIO, as it has been shown if we got CRC errors
in Ultra-DMA mode, we will have silent data corruption in multiword DMA mode
(isn't IDE wonderfull ? :).
Set timeout to 1s for "normal" ata I/O, to minimise the effects of missed
interrupts.
the disk is ready to transfer data, and in ATA-5 the DSC has been obsoleted.
So only wait for DRQ to transfer data. This can be made conditional on the
ATA version if it's proven to break with some drives (worked with all the
drives I have access to).
While I'm there correct a few typos.
In wdc_probe_caps() add code to guess the ATA revision supported (if
ATA4 if Ultra-DMA, ATA2 if PIO mode > 2). We can't rely on param.atap_ata_major
here, at last one Ultra-DMA drive claims to support only ATA-3.
Use the ATA version in ata_perror(), and to try a flush cache command
in a shutdown hook for IDE drives.
- keep the modes supported by the drive in struct ata_drive_datas (will be
later used for downgrading the DMA/PIO mode on error)
- use config flags to force/disable PIO/DMA/UDMA modes
- For the CMD PCI0643/6 setup DMA mode to DMA Read multiple.
device registers should be read back into the wdc_command structure after
successfull command completion. Use this this in wdioctl() for
ATAIOCCOMMAND.
an array of fixed-sized channel_softc elements. This way IDE controllers
which more than 1 channel (pciide) can extend the channel data easily
for private needs.
To avoid the double dereference at runtime, change the argument of
wdcstart() to the channel data pointer instead of the array index.
as with user-land programs, include files are installed by each directory
in the tree that has includes to install. (This allows more flexibility
as to what gets installed, makes 'partial installs' easier, and gives us
more options as to which machines' includes get installed at any given
time.) The old SYS_INCLUDES={symlinks,copies} behaviours are _both_
still supported, though at least one bug in the 'symlinks' case is
fixed by this change. Include files can't be build before installation,
so directories that have includes as targets (e.g. dev/pci) have to move
those targets into a different Makefile.
the capacity based on the c/h/s numbers. In fact, don't use the c/h/s
numbers for much of anything.
For ATA-4 drives or later, always use LBA mode, since it's now required.
Collectively, this allows >8GB disks (like the 12GB Bigfoot) to work.
bouyer