Also make TC framebuffer-console search table-driven.
Does not yet include "tcasic" layer; there's no such hardware on DECstations
and nothing for a tcasic layer to do.
into sys/dev/dec and split into a clockfns layer and a "middle" layer
for other DEC systems which use mcclocks with each onchip byte
register padded out to a 32-bit word.
Clone alpha/alpha/mcclock (also duplicated in pmax port) into
sys/dev/dec, and ifdef for default clockrates on pmax and alpha.
Use new machinery on pmax for ibus,ioasic attached mcclocks.
Replace all DS5000_* and DS3100 ifdefs with ifdefs on DEC_ options.
* Use MI declarations, not pmax-specific, in model-specific init
that uses baseboard (ioasic) registers.
* Further cleanup of machdep.c. Clock-tick still needs more thought.
* Use 'ibus' names for 3100 baseboard devices in MI code.
* add "Platform" support inpmax/pmax/sysconf.c and pmax/include/sysconf.h
(based on Alpha cpuconf.[ch], with a namechange to avoid clashes with
support for models of MIPS cpus. They differ more than Alphas).
* For each supported model of DECstation, create a separate file
with the support for that model. Use model codenames, since
support is really baseboard-specific and CPU daugherboards can change.
Move code from machdep.c and pmax_trap.c,
Add sysconf (nee "cpuconf") support.
* Rename model-specific functions to match sysconf names.
* Clean up autoconf.c. Use platform callbacks.
* Retire pmax_trap.c.
Leaves I/O bus configuration and console configuration untouched.
as pmax/dev/findcons.c:
* Follow the same logic: look for the device the PROM is using.
* If it's a framebuffer and we don't have a driver for it, try other
* framebuffers in PROM search order.
* If no match found, warn user and fall over to serial console.
* if no serial console found, go back to PROM.
Rework tc/scc.c attach routine to give cleaner initialization semantics.
Prune out old 'braindamage' code.
* Do rcons output properly, using cn_tab->cn_dev which points
at rcons cdevsw entrypoints.
* The pmadx console code was using keyboard (serial) device
(major,minor) for raster consoles with special code in the keyboard
drivers to catch output intended for consoles, pull it off the device
queue, and print them via cnputc().
Ifdef out RCONS_BRAINDAMAGE.
* Other minor cleanup to pmax scc driver.
tech-kern. Reported by Sean Davidson to cause erroneous doubling of
keyboard input on a 5000/50 under load.
Increasing the DELAY() from 2 to 30 doesn't help. Remove it for the
1.3 release. May cause problems with low-speed serial input, but
console keyboards work properly.
until a proper fix is available:
Perpetuate the 4.4bsd design even further. Change keyboard-driver
open routines to check for an active raster console. If active, set the
keyboard struct tty's t_winsize from the rcons t_winsize on first open.
See pr 4438 for remaining problems and discussion of a complete fix.
Add DDB interface to /sys/arch/mips/mips..
Rework heuristic stack traceback to work with DDB.
Add hooks to print exception log from DDB.
Add hooks from pmax console drivers: call Debugger()
after break from serial console, or 'DO' key from LK-xxx.
> revision 1.33
> date: 1997/05/15 02:15:55; author: thorpej; state: Exp; lines: +8 -4
> - In sccmatch(), check any user-specified offset, allowing scc unit numbers
> to be nailed down. From Ken Hornstein <kenh@cmf.nrl.navy.mil>, PR #3626,
> slightly modified to allow wildcarded offsets.
> - Blow away the cf->cf_unit check in sccmatch(); it's bogus.
Also gc usused references to NSCC and #include "scc.h"
jonathan