183442fe73
Emulate ulinear_be using slinear_be on later chips.
1998-08-14 00:49:23 +00:00
f750a7d47e
device ess was listed twice
1998-08-13 04:53:18 +00:00
a2dd74ed79
Merge paddr_t changes into the main branch.
1998-08-13 02:10:37 +00:00
58e0098fef
Shut up after close().
1998-08-12 21:36:21 +00:00
5c76b6a944
The mic preamp is really a property of the input stage, and affects both
...
pass-through and recording.
1998-08-12 19:13:14 +00:00
b170caf730
Completely rewrite media selection. Add support for the MII/PHY on
...
the 3Com 3c905-TX and 3c905-T4. Fix handling of the MII on the
3c595-MII and 3c597-MII (can't talk to the PHYs on these cards; just
use "manual" for the external MII port).
Fixes kern/4782 (Chris Demetriou).
1998-08-12 18:51:52 +00:00
fa39959a5e
Add a MIDI driver for the PC speaker. This is mostly of hack value,
...
but, hey, lotsa people got a MIDI device now! (A truly pitiful one. :-)
1998-08-12 18:16:36 +00:00
881b4053a6
Remove some white space.
1998-08-12 18:15:04 +00:00
3979b06d00
enhanced -> preamp
1998-08-12 03:18:34 +00:00
1f5c14d8ef
ess_audio_channel:active is now used even when DIAGNOSTICS is not defined.
1998-08-11 12:16:22 +00:00
a6e73a5576
Actually set all the logical filter bits. Doh!
1998-08-11 05:57:40 +00:00
271d3df6f3
Fix an obvious bug that caused the multicast filter to always be all 0s.
1998-08-11 04:18:25 +00:00
8ba8e2056b
Remove unused field (sc_ih) in ess_softc (interrupt handlers are kept
...
in a per-direction structure).
1998-08-10 20:24:26 +00:00
b034eb97bf
Fix typo.
1998-08-10 20:02:48 +00:00
7fca135b1b
Use the new trigger interface.
1998-08-10 15:32:18 +00:00
060f81eb62
Minor change.
1998-08-10 02:19:18 +00:00
93703857ca
Slow down, Wilbur.
1998-08-10 02:13:44 +00:00
7514d511f7
Fix a typo I introduced in the MIDI code.
1998-08-10 02:12:30 +00:00
8d77cae1b4
For models prior to the SB16, there is only one clock divider, so couple the
...
sample rates. However, only do this if both play and record are being used
simultaneously; otherwise we can't play 22KHz on the SB1.
1998-08-10 01:25:33 +00:00
3dcff6581b
Use the new trigger_{in,out}put interface.
...
Also, even on the SB1, we can leave the DMA controller in auto-initalize
mode and just send a command to the board for each block. This may help
prevent FIFO underruns.
1998-08-10 00:20:39 +00:00
b4e0bf5dfb
Use 4- and 8-byte DMA transfers.
1998-08-09 06:52:57 +00:00
0611fc34f8
Don't actually touch the hardware in set_params; defer that until we actually
...
start a transfer. Instead, just check that the parameters are valid.
Also, use 16-bit output for u-law and a-law.
1998-08-09 06:38:30 +00:00
5eba82397c
Oops; fix typo.
1998-08-09 04:59:55 +00:00
017b9af5fe
Clarify with a specific reference to the manual page in question.
1998-08-09 04:58:08 +00:00
12f5a41e1f
Make the previous slightly more robust, and set AUDIO_PROP_INDEPENDENT.
1998-08-09 04:40:55 +00:00
c8532af3b2
Make sure the sample rate is the same on both channels, tracking the change
...
from one channel to the other if only one is active.
1998-08-09 04:14:47 +00:00
759ca5ee0c
The manual says to use the other crystal for 22050Hz.
1998-08-09 03:48:42 +00:00
565adbaffb
Set the FIFO control bits correctly so that stereo recording works.
1998-08-09 02:54:50 +00:00
80457a2c65
Use auto-initialize DMA for recording.
1998-08-09 02:05:52 +00:00
e2686d0a1b
Use splnet, not splimp.
1998-08-08 23:51:39 +00:00
c49235f44c
Use splnet(), not splimp().
1998-08-08 23:44:12 +00:00
254afcaecb
Sleeping forever kinda sucks.
1998-08-08 21:37:00 +00:00
17932f0575
Set the correct modes for the record channel.
1998-08-08 20:55:36 +00:00
558733ffc6
Track our carrier status and report it in the media status callback.
1998-08-07 05:55:14 +00:00
7b044dea51
Make the irq checking logic somewhat less bogus.
1998-08-07 00:51:06 +00:00
48bae9ee88
Add MIDI support. The MIDI devices can be accessed as ``raw'' through
...
the /dev/rmidiN devices, or with a sequencer interface via /dev/music.
So far the only supported MIDI device is the MPU401 port on SoundBlaster
(and only on SB on isapnp, since we do not have locators with multiple
values yet).
1998-08-07 00:00:55 +00:00
0c6791d804
Add macro to test iobase validity.
1998-08-05 16:40:22 +00:00
f76fb48283
Use looping DMA for play channel.
...
More cleanup.
1998-08-04 13:14:42 +00:00
ce69d417a2
Make it compile without DIAGNOSTIC
1998-07-31 23:54:09 +00:00
6b407a79c6
Major cleanup of the ESS driver. It now sorta works. More to come.
1998-07-31 15:17:17 +00:00
75db93cec2
Pull in files.isapnp here; the two busses are linked together quite closely
...
(more than we'd like maybe, but don't we wish ISA didn't suck...)
1998-07-31 04:40:39 +00:00
11c3d96b49
Flush spurious #endif after ADDMULTI
1998-07-31 01:10:13 +00:00
bf52ef5697
Squash unused variable.
1998-07-30 22:17:34 +00:00
ae2fb64e3a
Document supported boards near the top of the driver source code.
1998-07-30 21:28:15 +00:00
b7a585b61d
Use the previously committed pnp hook.
1998-07-30 18:03:34 +00:00
8bd9c69e11
Multicast support.
1998-07-30 16:40:19 +00:00
cdeb158d5f
A first stab at making the SHARK sound work. It doesn't really work
...
yet, but it probes and makes a noise when used. Stay tuned!
1998-07-30 14:11:42 +00:00
d6a8a4f025
Don't print chip name in attach, the ad1848 attach already does.
1998-07-29 11:39:25 +00:00
20f454ae1c
KNFify.
1998-07-28 20:58:39 +00:00
a374ab61d8
ic/i82595reg.h
1998-07-28 16:02:34 +00:00
mycroft