reception and saving other "bad frames" (i.e. ones that are larger
than the standard Ethernet frame length) if we have VLANs configured
on the interface.
when running at splserial(). This is a temporary measure (until
there's a MP-safe interrupt handling structure); until then, it should
be used when MULTIPROCESSOR and IPL_SERIAL > IPL_SCHED.
and a front-end driver for the Ether3. Only semantic change is to remove
ea_claimirq() and ea_releaseirq() on the grounds that the seem too spurious
to warrant a callback to the front-end.
VGA_CONSOLE_SCREENTYPE because the screen types are hardware specific
and make it affect the console only (no need to change runtime
behaviour), don't call vga_setscreentype() unless necessary (to avoid
trouble with strange hardware - PR kern/11025)
-some beginnings of ISO-7 (greek) font support
* in vga_init(), set the screen type to WSCONS_DEFAULT_TYPE, which defaults
to "80x25".
XXX: the code currently makes no attempt to ensure that a font
with the appropriate width & height is available, effectively
limiting this default to either "80x25" or "80x24" at this
time.
* make wsdisplay_screentype_pick() non static, so that vga_init() can use it
-support access to MII_ANER too for completeness
-remove some hacks which disappeared in FreeBSD if_rl.c
rev. 1.25 (Aug 31 14:45:49 1999)
(the driver could need more updating, but this is what I've tested
for months)
- Pull in linkage useful for both PCI and EISA boards from cac_pci.c.
- cac_ccb_done() now frees the done CCB if the CCB callback completes.
- Model-specific linkage is now responsible for DMA synchronization.
- Use wakeup_one() in cac_ccb_free().
- Start synchronous commands `manually'.
- Add one hardware check in DIAGNOSTIC case.
- Improve error messages.
- Start firmware background tasks on controllers that need it.
as used on later arm26 system (A5000, A4, A3010, A3020, A4000).
What we have got:
...
upc0 at iobus0 base 0x010000: config state bb 87 1c 00 00
fdc at upc0 offset 0x3f4 not configured
wdc0 at upc0 offset 0x1f0
lpt0 at upc0 offset 0x278
com0 at upc0 offset 0x3f8: ns8250 or ns16450, no fifo
...
What we haven't got:
- FDC support (found, but not configured).
- Clearing lpt interrupts on arm26 systems (needs help from IOEB).
- A upc(4) manual page.
- More than minimal testing (my A3020s don't have root devices).
- A proper probe routine (arm26 can't use one anyway).
response queue entry). Clean up some of the Fibre Channel completion
stuff so that thing we check actually match the current manual. There's
only one silly lossage that the manual doesn't cover at present- if
an FC command completes with SV (sense valid), the f/w does *not* s
et "GOT_STATUS" in the state bits- I guess they assume that you'd figure
out that if you have SENSE DATA you probably have a CHECK CONDITION. Still-
yet another fine f/w frotz from Qlogic. Add in an ISP_EXEC_THROTTLE
define to set a per-device execution throttle.
onintstack to be real integers. Add ISP_ILOCK/ISP_IUNLOCK macros.
Fix the isp_lock/isp_unlock inlines to stop being so embarrassingly
in error. Why, or why, can't I have mutex_enter/mutex_exit, pretty please?
Clarify some startup SCSI mode settings. Insist that the FC f/w options
*must* have ICBOPT_PDBCHANGE_AE set (wasted a half day on this crock).
Make a specific comment in isp_start that the tags being selected for FC
cards, in lieu of any set by the outer layers, are there for safety's sake.
This removes the change from a previous commit.
For the ISP_TOGGLE_TMODE function, do a complete reset, not just an
isp_init (info from Solaris port). Make some cleanup changes for
code clarity.
98715* series.
The MX98715AEC-[C,E] use a different location in the serial eerom for
LED control, and programming it with the original location's values
caused unpredictable behavior.
Also, start integrating fixes where media changes on an adapter
under load may fail. There's more work to be done here, but I need
to sort out our internal changes a little more carefully.
break character with the supplied one. This is useful for cases where
break is hard to generate, or you are connected to a PC that "sends"
breaks when power cycled. For this mode in com, interpret break char
in the polling section, which allows entry into the debugger before
the tty is opened. Only supported in the com driver currently.
interace cleanups, some new common functions. The major impact that
will be noticeable right away is that if you boot with not Fibre connected
to the FC cards, you no longer hang indefinitely.
Reset the scsi bus at attach time, to be sure all devices start in narrow/async
mode.
Defer sync/wide negotiation until after whe have a valid
xs->sc_link->device_softc, so that we can honnor the NOSYNC/NOWIDE quirks.
volatile flags (isp_mboxbsy- keeps a bitmask of expected output mailbox
registers) and storage for them (isp_mboxtmp). Get rid of macroized
LUN widths. This is determined at run time.
in new MBOX_WAIT_COMPLETE/MBOX_NOTIFY_COMPLETE macros (ready for SMPizing).
Define STRNCAT inline for our usage.
Stealing a bit of the xs_status flags to maintain command state that
is pertinent for the hBA- should really reserve them for private usage
in scsipiconf.h.
Qlogic controller driven by this chipset. If they don't want the verbosity,
don't compile a DIAGNOSTIC kernel.
Major amount of mailbox command rewrites- hopefully should fix some of the
outstanding PRs.
Change header to note that this is no longer maintained at NASA/Ames.
u_int8_t array to struct ieee80211_nwid to prepend length field.
The length field is necessary because IEEE 802.11 spec doesn't prohibit
even '\0' for SSID.
Though the name and the value of SIOC... macro is unchanged, this change
breaks binary compatibility. The only affected userland program on the
tree is ifconfig(8).
As Jason suggested on tech-net, it is better than live with problems
since there are no releases for this ioctls yet.
arc4 implementation by Kalle Kaukonen has been added.
define "wlan" in files.
XXX: only awi depends on wlan for now.
Allow authentication for adhoc (IBSS) mode.
Disable adhoc mode without bssid (mediaopt adhoc,flag0) for FH radio.
FH cannot work without synchronization by beacons.
Align IP header for ethernet encapsulation (IFF_FLAG0) mode.
Print available access points for IFF_DEBUG.
apparently no longer necessary (probably due to other fixes that
have happened in the filter setup path) and is in fact harmful.
Based on a patch from Krister Walfridsson, who claims this makes
his newer NetGear FA-310TX work (although, my older NetGear FA-310TX
still does not, but fails in an entirely different way).
which is revealed with larger HZ systems like NetBSD/pmax (256Hz)
and NetBSD/alpha (1024Hz) as reported by PR#8645. Polled tape
drive access is done with maximum 6 hour timeout which ended up
with negative time and then confused SCSI bus severely.
memory that is explicitly mapped in a DMA-coherent manner, we must
make sure to PREREAD sync the RFA after noticing a clear "complete"
bit. Without this, the clear bit will linger in the cache, and the
CPU will not notice when the chip updates the bit via DMA later.
From Izumi Tsutsui on port-arm32@netbsd.org.
<vm/pglist.h> -> <uvm/uvm_pglist.h>
<vm/vm_inherit.h> -> <uvm/uvm_inherit.h>
<vm/vm_kern.h> -> into <uvm/uvm_extern.h>
<vm/vm_object.h> -> nothing
<vm/vm_pager.h> -> into <uvm/uvm_pager.h>
also includes a bunch of <vm/vm_page.h> include removals (due to redudancy
with <vm/vm.h>), and a scattering of other similar headers.
"off_t" and the return value is a "paddr_t" to allow mappings
at offsets past 2^31 bytes. Somewhat inspired by FreeBSD, which
only changed the offset to a "vm_offset_t".
Includes updates for the i386, pc532 and sh3 mmmmap from Jason Thorpe.
such as the LM78 and VT82C686A (and eventually ACPI). Multiple
sensor devices can be hooked registered with `sysmon', and eventually
sysmon will also handle hardware (and software) watchdog timers.
Convert the `lm' and `viaenv' drivers to the new interface.
add opt_awi.h to define AWI_DEBUG, AWI_WEP_ARC4.
show the firmware version at attach.
create a framework to support WEP (encryption code is not included for now).
a new wiconfig compatible ioctl interface replaced the awictl interface.
fix memory leak in selecting AP
fix bugs in ESSID selection
changes from FreeBSD-current by Warner Losh:
revision 1.2
date: 2000/04/17 22:58:15; author: imp; state: Exp; lines: +16 -1
Provide mem* for compat with NetBSD to fix LINT
fixes from FreeBSD-current by Guido van Rooij:
revision 1.4
date: 2000/05/29 19:58:10; author: guido; state: Exp; lines: +5 -2
Fix a panic resulting from an obvious null pointer deref.
Apparently some other panics still exist in this driver, but with
this fix, it was at least possible to run the Nokia card at SANE 2000.
from devices connected to pckbc:
- Do actual sample collection in pckbc.
- Add rndsource_element_t to the slot data.
- Change pckbc_set_inputhandler() to take an additional argument,
the name of the device, which is (eventually) passed into
rnd_attach_source() to identify the source.
- Change callers of pckbc_set_inputhander() appropriately.
and scsipi_device respectively, with size reduction of ncr53c9x_softc.
Specifying NULL instructs the driver to use default adapter and default
device codes. Every target port has ncr53c9x_attach(sc, NULL, NULL) anyway.
have _detach() functions:
Ensure that softc keeps state about whether the attach succeeded,
and make the detach function return immediately if the attach did
not complete.
and QUEUE FULL cases; this is already done for all BAD_STATUS cases.
Make sure to requeue the SCB in the above cases internally in the driver,
the SCSI layer doesn't know how to deal with it properly.
some devices may not be found if the BIOS (which would normally
do the reset at startup) is disabled. Should really be done from the SCSI
layer.
Implement the SCBUSIORESET ioctl.
This bug is only visible on some disks, and I have verified that it works
correctly on VAX. However, du to the author, it is a problem on other
machines/disks as well. Here's the author's comments:
> The MI code for the NCR5380 has a small bug in it The RZ56 wants to
> negotiate for Synchronous Data Transfers and when it does, the current code
> looks like it will send a REJECT message as the spec calls for when we cant
> handle the request. However, a couple of lines of code in the
> ncr5380_msg_in routine are missing wrt the PARITY message and anything that
> wants to send a REJECT message. The ATN setup that is done in
> ncr_sched_msgout is immediately negated by the final byte ACK sequence in
> this routine. This causes bad things to happen to an RZ56.
re-enqueueing an already free ccb.
Prepare the background to have a unique initialization function for
all of the supported host adapters.
Rename a lot of #define in a more sane way.
Move Carriers initialization and defines in adwmcode.{c,h}
Don't lose Carrier nodes in case of a BUS/Chip reset explicitly invoked
after a DMA failure.
XXX - DMA failure still arise when AdvanSys U[2]W host adapters are used
in conjunction with Intel 82443BX Host Bridge/Controller (rev. 0x03).
!?!Have to understand why!?!
enami