* Add (commented out) type and asmtype commands. asmtype will
be used to define the gcc constraint used to emit constants
and type will be used to define the type the constant should
get casted to before passing it to printf.
* Added LKM, PFIL_HOOKS and NFSSERVER options.
* Added four ccd devices.
* Removed PLIP and NO_INLINE_SPLX options.
* Removed MFS, MSDOSFS, CD9660, FDESK, KERNFS and PROCFS filesystems
because they all are lkmable.
Eliminate obsolete global kernel variable "struct timezone tz"
Add RTC_OFFSET option
Add global kernel variable rtc_offset, which is initialized by
RTC_OFFSET at kernel compile time.
on i386, x68k, mac68k, pc532 and arm32, RTC_OFFSET indicates how many
minutes west (east) of GMT the hardware RTC runs. Defaults to 0.
Places where tz variable was used to indicate this in the past have
been replaced with rtc_offset.
Add sysctl interface to rtc_offset.
Kill obsolete DST_* macros in sys/time.h
gettimeofday now always returns zeroed timezone if zone is requested.
settimeofday now ignores and logs attempts to set non-existant kernel
timezone.
* Add IPL_HIGH. Alias IPL_HIGH to IPL_RTTY
* Define splrtty (used by the scn driver).
* Add iv_level and iv_mask to struct iv. These define the IPL at
which the handler should run.
* intr_establish now takes *two* ipls. One at which the handler should run,
and one in which the interrupt should get blocked.
* Define SCN_RING_HIWAT and add sc_rbhiwat to scn_softc. When the
ringbuffer gets full up to this mark, rts gets asserted (Ian Dall).
* Add sc_rx_blocked to scn_softc. This is used to tell scnsoft that
rxinterrupts are blocked (Ian Dall).
* intr_establish now takes *two* ipls. One at which the handler should run,
and one in which the interrupt should get blocked.
All the following changes were provided by Ian Dall:
* Remove SCN_HSOFT. Now that the pc532's software interrupt system is running
from int14, this won't work anymore.
* Add code to detect uart type (SCN2681, SCC2692 or SCC26C92).
* Cleanup my RECOVER mess. Thank's to Ian Dall for reading the datasheet
and removing all the unnecessary RECOVERs.
* Cleanup scnrxintr.
* Implement scnhiwflow.
* Do not use automatic RTS. This and scnhiflow and some changes to the
interrupt system suggested by Ian fix the scn overrun problem at 57600
baud.
* intr_establish now takes *two* ipls. One at which the handler should run,
and one in which the interrupt should get blocked.
* Make transfersize configurable for input and output. Default the input
transfersize to 128 bytes. That way interrupts won't be disabled for more
then about 128us-256us for slow targets. This is necessary to prevent scn
fifo overruns. Cleanup the pdma code. Thank's to Ian Dall for these
changes.
* Make it work on 30mhz machines.
* Configure MSDOSFS, CD9660, KERNFS, NFSCLIENT and INET.
* Configure SCSI-cds, slip and ppp.
* Update for mi ramdisk driver.
* Initialize iv_level for all interrupts.
* Protect the call to the sir-handler with splraise.
* intr_establish now takes *two* ipls. One at which the handler should run,
and one in which the interrupt should get blocked.
* Compute iv_mask for all interrupts in intr_establish.
on indirect-config busses a (permanent) softc that they could share
between 'match' and 'attach' routines:
Define __BROKEN_INDIRECT_CONFIG so that old autoconfiguration
interfaces are used, until drivers are converted to use the new
interfaces (actually, converted back to use the _older_ interfaces)
which prohibit indirect configuration devices from receiving a softc
in their match routine that they can share with their attach routine.
Lets users over-ride with makeoptions COPTS="..." in kernel config files.
Leave `mandatory' flags (like -msoft-float which on m68k enforces no
FP in kernel) in CFLAGS.
* Support for the new softint mechanism. Softints are now requested by
triggering an unused ICU hardware interrupt. The idea for this was
contributed by Phil Budne.
* Real probe code added.
* Duart info is now allocated only for devices that are present.
* Added IO-Recovery delays for 30mhz systems.
* Removed a few potential NULL-pointer references.
* Only FFS is needed for the install kernel.
* Configure the console to 8N1 (that's what the pc532's rom monitor uses).
* The install kernel doesn't need to know about CDROM drives.
* Use the new mi ramdisk.
* New patchable variable maxphysmem to limit physical memory.
That's useful to simulate small machines for testing install
kernels.
* Make debugging crashdumps with gdb -k work.
* microtime is moved to clock.c.
* Reserve memory for symbol table when ddb is configured.
* Move checks for RB_KDB into consinit.
* Fix a typo in delay().
* Disable generation of profiling prologue for proc_trampoline,
sigcode, idle, handle_trap, flush_icache, svc and interrupt.
* A few tweaks to make kgdb and ddb work nicer.
* Support for bpf added.
* Don't duplicate code, use ether_ifattach instead.
* Recode plipreceive and pliptransmit in assembler.
This improves performance from 40 kbyte/s to 50 kbyte/s
between a 30mhz pc532 and a 25mhz i386.
multi-channel driver), or to SCSI_CHANNEL_ONLY_ONE if a
single-channel driver.
(2) use scsiprint() rather than a locally-defined autoconfig print
function, and kill any locally-defined print function.
a char *, because that's what was really intended, and because
if the print function modifies the string, various things could become
unhappy (so the string should _not_ be modified).
* Make S expand to an absolute path at compile time.
* Use `-S' rather than `-x' to remove debugging symbols.
* Garbage collect unused variables.
* Reverse a handful of port-specific changes that do not correspond to
the common build model and are not needed.
a boot string for firmware that can do this, such as the SPARC and
the sun3 models. It is currently silently ignored on all other
hardware now, however. The MD function "boot()" has been changed to
also take a char *.
matthias