- clean up debug code
- Don't check ATAPI signature when probing ATA drives, ATAPI devices were
detected before
- Reset controller after disks probes. The probe, with some combinations of
ATA/ATAPI device keep it in a mostly working, but strange state (with busy
led on)
- The WDCF_IRQ_WAIT flag is now cleared by wdc_ata_intr and wdc_atapi_intr
when appropriate (helps recover from failure conditions)
- In wdcunwedge, send ATAPI_SOFT_RESET to non-ata drives
(helps recover from failure conditions)
- in wdctimeout be a bit more verbose when we missed an interrupt
- Always Increment xfer->c_skip where it should be
- Set the ITSDONE flag when a polled command completed.
for 12-bit addresses. This causes PCMCIA cards mapped at 0x400 and higher
to not function properly. However, the range 0x300-0x3ff causes some
laptops (e.g. the NEC Versa 6030X) to hang if cards are mapped there.
So, after some experimentation, we compromise. If the probe discovers
a 12-bit address bus, don't trust it. Instead, use the range 0x330-0x3ff.
This has been shown to work on the laptops that the 0x300-0x3ff range is
known to fail on.
supports generic SMC91cxx-based ISA cards and the built-in SMC
Ethernet found in some laptop docking stations.
Thanks much to Andrew Gillham <gillhaa@ghost.whirlpool.com> for
making this work!
more robust in resource shortage situations, basically identical to
code I added to the "ahc" driver some time ago.
Thanks to Brad Spencer for the testing help.
* Make the ring buffer size and water marks patchable, and allocate the buffer
separately.
* Do the ttymalloc() at attach time.
* Reorganize the receive buffer so the status and data pair are next to each
other. This is slightly faster.
* Make sure we actually do turn off interrupts in comclose() if we have DDB
configured and it's not the console. (D'oh!!!!)
* When we exhaust the current transmit run, turn off transmit interrupts in
comintr(), so we're fairly sure we don't get another one.
* Nuke the silly lsrmap[] idea; it's slower in the normal case.
* Cache the l_rint pointer in the soft interrupt routine.
* Carrier detect (TS_CARR_ON) is based on the actual DCD bit, even if it's
being ignored.
* Set TS_WOPEN early on in zsopen().
* Don't disable interrupts on the console during close if we have DDB.
Inert changes:
* Don't handle ZS_HWFLAG_NO_DCD here; the frontend does it.
* Deprecate `register'.
* Use SET(), CLR(), and ISSET().
More performance changes:
* Rototill receive handling; use a backpressure mechanism to prevent livelock.
* Output silo/ibuf overflow warnings at most once per minute, from a callout.
* When we exhaust the current transmit run, turn off transmit interrupts in
zstty_txint(), so we're fairly sure we don't get another one.
* Make the ring buffer size and water marks patchable, and allocate the buffer
separately.
* Do the ttymalloc() at attach time.
* Reorganize the receive buffer so the status and data pair are next to each
other. This is slightly faster.
* Make sure we actually do turn off interrupts in comclose() if we have DDB
configured and it's not the console. (D'oh!!!!)
* When we exhaust the current transmit run, turn off transmit interrupts in
comintr(), so we're fairly sure we don't get another one.
* Nuke the silly lsrmap[] idea; it's slower in the normal case.
* Cache the l_rint pointer in the soft interrupt routine.
Supports changing media with ifconfig's "media" directive.
This splits the 3c503 functionality out of the ISA "ed" driver, much the
same way NE2000 support was split out.
christos