to do uncached memory access during VM operations (which can be
quite expensive on some CPUs).
We currently write-back PTEs as soon as they're modified; there is
some room for optimization (to write them back in larger chunks).
For PTEs in the APTE space (i.e. PTEs for pmaps that describe another
process's address space), PTEs must also be evicted from the cache
complete (PTEs in PTE space will be evicted durint a context switch).
counters. These counters do not exist on all CPUs, but where they
do exist, can be used for counting events such as dcache misses that
would otherwise be difficult or impossible to instrument by code
inspection or hardware simulation.
pmc(9) is meant to be a general interface. Initially, the Intel XScale
counters are the only ones supported.
SCSIPI_ADAPT_POLL_ONLY to tell the MI scsipi layer to do it for us. This,
plus G/Cing some debugging code, removes the card-specific scsi_request
wrappers.
into platform-specific initialization code, giving platform-specific
code control over which free list a given chunk of memory gets put
onto.
Changes are essentially mechanical. Test compiled for all ARM
platforms, test booted on Intel IQ80321 and Shark.
Discussed some time ago on port-arm.
be properly used by any misc. cloning device. While here, correct
a comment to indicate that "open" is the only entry point and that
everything else is handled with fileops.
MALLOC_NOINLINE, and VNODE_OP_NOINLINE. The exceptions are when they
include another config files that already defines the options, or if
they are for an embedded board, just define a few extra options, and
do not already define PIPE_SOCKETPAIR.
assigned by RISCOS Ltd (and were assigned by Acorn) to be unique across all
manufacturers. This means that associating each one with a manufacturer (and
checking the manufacturer when attaching) is bogus. Thus, we don't do that
any more.
This should have the pleasant side-effect of getting APDL IDE interfaces
working, since they're just ICS ones with a different manufacturer ID.
internally). Move arm/iomd/pms* to arm/iomd/opms*. Mechanical change,
tested by cross-compiling a kernel from i386.
Approved by christos.
XXX: What are arm/arm32/conf.c and arm/include/conf.h good for?
file, <arm/cpuconf.h>, which pulls in "opt_cputypes.h" and then defines
the following:
* CPU_NTYPES -- now many CPU types are configured into the kernel. What
you really want to know is "== 1" or "> 1".
* Defines ARM_ARCH_2, ARM_ARCH_3, ARM_ARCH_4, ARM_ARCH_5, depending
on which ARM architecture versions are configured (based on CPU_*
options). Also defines ARM_NARCH to determins how many architecture
versions are configured.
* Defines ARM_MMU_MEMC, ARM_MMU_GENERIC, ARM_MMU_XSCALE depending on
which classes of ARM MMUs are configured into the kernel, and ARM_NMMUS
to determine how many MMU classes are configured.
Remove the needless inclusion of "opt_cputypes.h" in several places.
Convert remaining users to <arm/cpuconf.h>.
and pte_l2_s_cache_mode. The cache-meaningful bits are different
for these descriptor types on some processor models.
* Add pte_*_cache_mask, corresponding to each above, which has a mask
of the cache-meangful bits, and define those for generic and XScale
MMU classes. Note, the L2_S_CACHE_MASK_xscale definition requires
use of the Extended Small Page L2 descriptor (the "X" bit overlaps
with AP bits otherwise).
Significant cleanup, here, including better PTE bit names.
* Add XScale PTE extensions (ECC enable, write-allocate cache mode).
* Mechanical changes everywhere else to update for new pte.h. While
doing this, two bugs (as a result of typos) were fixed in
arm/arm32/bus_dma.c
evbarm/integrator/int_bus_dma.c
* Don't refer to VA 0, instead refer to a new variable: vector_page
* Delete the old zero_page_*() functions, replacing them with a new
one: vector_page_setprot().
* When manipulating vector page mappings in user pmaps, only do so if
the vector page is below KERNEL_BASE (if it's above KERNEL_BASE, the
vector page is mapped by the kernel pmap).
* Add a new function, arm32_vector_init(), which takes the virtual
address of the vector page (which MUST be valid when the function
is called) and a bitmask of vectors the kernel is going to take
over, and performs all vector page initialization, including setting
the V bit in the CPU Control register ("relocate vectors to high
address"), if necessary.
become ippp (ISDN ppp) and irip (ISDN raw IP). The character device now
are called: /dev/isdn (isdnd <-> kernel communication), /dev/isdnctl (dialing
and other control), /dev/isdntrc* (tracing), /dev/isdnbchan* (raw B channel
access, i.e. for user land PPP) and /dev/isdntel* (telephone devices, i.e.
for answering machines).
tell nothing in the acorn32 port was using this version of
MEMORY_DISK_SIZE but I've left the code here incase the portmaster
wants it.
* rename MINIROOTSIZE to MEMORY_DISK_SIZE, so that all md(4) options
are consistently named
* fold opt_mdsize.h into opt_md.h
