established.
XXX real fix: make enable/disable for real and invoke them when needed.
XXX This has to wait until the layer 1 <-> layer 2 interface is
XXX restructured.
This is not unprecedented, as we do it in >100 places in the tree.
If you disagree with this philosophy, take it to tech-kern for a discussion
FIRST before reverting; TNF, not one particular person, owns this file.
o Add NAKAGAWA METAL's LNT-10TN card.
o Add KINGSTON KNE-PC2 ethernet card.
o Add RATOC REX_R280 card.
o Add $FreeBSD$ id.
I've not added these cards the their respective drivers, however.
XXX I think we should have if_ne_pcmcia.c try to allocate I/O addresses
around 0x300 or we'll end up with a lot of quirks for NE2k based
cards which have bad CIS's.
be attached with this flag.
Some CF Card (for ex. IBM MicroDrive and SanDisk) doesn't seem to implement
drive select command. In this case, you can't eliminate ghost drive properly.
So you should use this flag to ignore the ghost by force.
This is the kernel part (userland to follow soon) of the latest (and
very probably last) release (version 0.96) of ISDN4BSD. ISDN4BSD has a
homepage at http://www.freebsd-support.de/i4b/.
It gives the user various ways to use the isdn connection: raw data (via
the i4brbch "raw b-channel" device), ppp (via the isp "isdn PPP" device),
voice/answering machine (the i4btel "telephone" device) and ip over isdn
(the ipr device, "IP over raw ISDN").
Supported are a bunch of common and older cards, more to be added soon
after some cleanup. Currently only the european E-DSS1 variant of the
ISDN D channel protocol is supported.
timeouts).
stop driver after suspend.
XXX: should use command interrupt but no document...
XXX: status update sometimes failed perhaps due to collision.
(RID 0xff50 or 0xff68 access failed)
No vendor ID, no product ID, and the wpp_cis_info is 'PCMCIA', 'CD-ROM'.
I'd be encouraged at some progress towards 'generic devices', except
someone else is bound to produce something that identifies the same, but
requires a quirk. Can I go back to my sparc now?
Make two other comments consistent while here.
Though ifconfig -m no longer show 5Mbps/11Mbps for PC4500 by this fix,
I cannot find how to set fixed transmit speed to the firmware.
FreeBSD version of driver apparently ignore the value set by ancontrol(8).
This is very adhoc work for IETF meeting.
- Since it seems that 'an' and 'wi' have similar hardware, low level
functions should be shared.
- There are PCI/ISA cards of Aironet but not supported yet.
- The wiconfig interface is changed so that wiconfig cannot be used.
- 'ancontrol' of FreeBSD is not ported.
- Only infrastructure mode is tested.
- WEP is not supported.
Though I only have an Aironet card, Cisco card should be expected to work.
- Doesn't fail ne_pcmcia_attach() if ne_pcmcia_ax88190_set_iobase() failed.
- Check whether LIOBASE register is writable or not (dirty hack!).
Fix PR. 11285
when sharing an interrupt with other devices:
check sc->sc_enabled, and drop the interrupt if its' off.
Also check for IFF_RUNNING, on advice of Enami Tsugotomo.
instead of addr1 and addr2. THis means that tcpdump -e will show the
correct MAC address for communications with access points instead of showing
the BSSID.
In the future there should be 802.11 support for bpf/libpcap/tcpdump,
but that is aways down the road.
Also fix a typo in a comment.
registers. rationale:
- Netwave cards choke if we map i/o memory to >= 0x400
- even though, CIS tuple talks nothing about it
- it is not possible to specify range in pcmcia_io_map
- it would be very bad to do a try-and-error bus_space allocation for
i/o memory regions < 0x400
- we can have exactly the same functionality with memory mapped access
this should correct PR 10139.
the memory mapped access idea was from WIDE wildboar/bsdi cnw code.
u_int8_t array to struct ieee80211_nwid to prepend length field.
The length field is necessary because IEEE 802.11 spec doesn't prohibit
even '\0' for SSID.
Though the name and the value of SIOC... macro is unchanged, this change
breaks binary compatibility. The only affected userland program on the
tree is ifconfig(8).
As Jason suggested on tech-net, it is better than live with problems
since there are no releases for this ioctls yet.
arc4 implementation by Kalle Kaukonen has been added.
define "wlan" in files.
XXX: only awi depends on wlan for now.
Allow authentication for adhoc (IBSS) mode.
Disable adhoc mode without bssid (mediaopt adhoc,flag0) for FH radio.
FH cannot work without synchronization by beacons.
Align IP header for ethernet encapsulation (IFF_FLAG0) mode.
Print available access points for IFF_DEBUG.
add opt_awi.h to define AWI_DEBUG, AWI_WEP_ARC4.
show the firmware version at attach.
create a framework to support WEP (encryption code is not included for now).
a new wiconfig compatible ioctl interface replaced the awictl interface.
fix memory leak in selecting AP
fix bugs in ESSID selection
changes from FreeBSD-current by Warner Losh:
revision 1.2
date: 2000/04/17 22:58:15; author: imp; state: Exp; lines: +16 -1
Provide mem* for compat with NetBSD to fix LINT
fixes from FreeBSD-current by Guido van Rooij:
revision 1.4
date: 2000/05/29 19:58:10; author: guido; state: Exp; lines: +5 -2
Fix a panic resulting from an obvious null pointer deref.
Apparently some other panics still exist in this driver, but with
this fix, it was at least possible to run the Nokia card at SANE 2000.
have _detach() functions:
Ensure that softc keeps state about whether the attach succeeded,
and make the detach function return immediately if the attach did
not complete.
ichiro