NULL for root PCI busses. For busses behind a bridge, it points to
a persistent copy of the bridge's pcitag_t. This can be very useful
for machine-dependent PCI bus enumeration code.
* Implement a machine-dependent pci_enumerate_bus() for sparc64 which
uses OFW device nodes to enumerate the bus. When a PCI bus that is
behind a bridge is attached, pci_attach_hook() allocates a new PCI
chipset tag for the new bus and sets it's "curnode" to the OFW node
of the bridge. This is used as a starting point when enumerating
that bus. Root busses get the OFW node of the host bridge (psycho).
* Garbage-collect "ofpci" and "ofppb" from the sparc64 port.
* Pull in dev/mii/files.mii from conf/files, rather than playing
the magic "files include order" dance in N machine-dependent
configuration definitions.
not pre-load the chip's Tx buffer, but instead waits for the Tx Ready
interrupt to transmit the first chunk of data.
* On the IOP310, set COM_HW_NO_TXPRELOAD, rather than COM_HW_TXFIFO_DISABLE.
This solves the "UART hangs" problem on the Npwr in a nicer way (i.e. we
get to use the FIFO, whee). The COM_HW_NO_TXPRELOAD happens to match the
Linux 16550 driver's Tx algorithm, and the "UART hang" was never observed
on the Npwr running Linux.
Eventually, we might want to eliminate the COM_HW_NO_TXPRELOAD, and simply
always use its algorithm. But it should be tested on more 16x50 variants
before we do that.
Kudos to Valeriy Ushakov <uwe@netbsd.org> for pointing out this solution
(which also happens to fix the stray UART interrupt issue on the Krups
Javastation), and to Allen Briggs <briggs@netbsd.org> for experimenting
with various methods of fixing this.
file, <arm/cpuconf.h>, which pulls in "opt_cputypes.h" and then defines
the following:
* CPU_NTYPES -- now many CPU types are configured into the kernel. What
you really want to know is "== 1" or "> 1".
* Defines ARM_ARCH_2, ARM_ARCH_3, ARM_ARCH_4, ARM_ARCH_5, depending
on which ARM architecture versions are configured (based on CPU_*
options). Also defines ARM_NARCH to determins how many architecture
versions are configured.
* Defines ARM_MMU_MEMC, ARM_MMU_GENERIC, ARM_MMU_XSCALE depending on
which classes of ARM MMUs are configured into the kernel, and ARM_NMMUS
to determine how many MMU classes are configured.
Remove the needless inclusion of "opt_cputypes.h" in several places.
Convert remaining users to <arm/cpuconf.h>.
and pte_l2_s_cache_mode. The cache-meaningful bits are different
for these descriptor types on some processor models.
* Add pte_*_cache_mask, corresponding to each above, which has a mask
of the cache-meangful bits, and define those for generic and XScale
MMU classes. Note, the L2_S_CACHE_MASK_xscale definition requires
use of the Extended Small Page L2 descriptor (the "X" bit overlaps
with AP bits otherwise).
Significant cleanup, here, including better PTE bit names.
* Add XScale PTE extensions (ECC enable, write-allocate cache mode).
* Mechanical changes everywhere else to update for new pte.h. While
doing this, two bugs (as a result of typos) were fixed in
arm/arm32/bus_dma.c
evbarm/integrator/int_bus_dma.c
* Don't refer to VA 0, instead refer to a new variable: vector_page
* Delete the old zero_page_*() functions, replacing them with a new
one: vector_page_setprot().
* When manipulating vector page mappings in user pmaps, only do so if
the vector page is below KERNEL_BASE (if it's above KERNEL_BASE, the
vector page is mapped by the kernel pmap).
* Add a new function, arm32_vector_init(), which takes the virtual
address of the vector page (which MUST be valid when the function
is called) and a bitmask of vectors the kernel is going to take
over, and performs all vector page initialization, including setting
the V bit in the CPU Control register ("relocate vectors to high
address"), if necessary.
