recovering from a possible race condition in sii_intr, read the active
target from the destat register, and set the softc state pointer
`state' appropriately. (This warning is in a block that prints a
warning message, and the warning message has _never_ been seen. The
bug is probably innocuous.)
Also addresses the `more thought needed' in the log message for rev. 1.12.
respectively), so console setup code can test forconfiguration of the
correct front-end (via NDC_DC and NDC_IOASIC, respectively).
Delete 'needs-flags' from dc.c. GC obsolete uses of NDC, "dc.h".
> revision 1.33
> date: 1997/05/15 02:15:55; author: thorpej; state: Exp; lines: +8 -4
> - In sccmatch(), check any user-specified offset, allowing scc unit numbers
> to be nailed down. From Ken Hornstein <kenh@cmf.nrl.navy.mil>, PR #3626,
> slightly modified to allow wildcarded offsets.
> - Blow away the cf->cf_unit check in sccmatch(); it's bogus.
Also gc usused references to NSCC and #include "scc.h"
(The operator-precdence changes in 1.11 were pulled up in rev 1.14).
* If the chip asserts a SCSI-bus error (SII_BER) in sii_intr,
reset the SII_BER bit instead of ignoring it.
XXX SII_BER May need checking and resetting elsewhere.
Fixes broken blitting from rcons.
* Put back old 4.4bsd range test on cursor movement. 1.2 code is broken.
* Disable screensaver, it reportedly never comes back on properly.
Some of the stuff (e.g., rarpd, bootpd, dhcpd etc., libsa) still will
only support Ethernet. Tcpdump itself should be ok, but libpcap needs
lot of work.
For the detailed change history, look at the commit log entries for
the is-newarp branch.
needed. When sfbattach() initializes the fbinfo data, it was corrupting
data past the struct device data actually allocated. This does not appear
to have caused a problem in the past, but causes a problem with the new
setroot() changes by Jason.
Eliminate obsolete global kernel variable "struct timezone tz"
Add RTC_OFFSET option
Add global kernel variable rtc_offset, which is initialized by
RTC_OFFSET at kernel compile time.
on i386, x68k, mac68k, pc532 and arm32, RTC_OFFSET indicates how many
minutes west (east) of GMT the hardware RTC runs. Defaults to 0.
Places where tz variable was used to indicate this in the past have
been replaced with rtc_offset.
Add sysctl interface to rtc_offset.
Kill obsolete DST_* macros in sys/time.h
gettimeofday now always returns zeroed timezone if zone is requested.
settimeofday now ignores and logs attempts to set non-existant kernel
timezone.
on indirect-config busses a (permanent) softc that they could share
between 'match' and 'attach' routines:
Define __BROKEN_INDIRECT_CONFIG so that old autoconfiguration
interfaces are used, until drivers are converted to use the new
interfaces (actually, converted back to use the _older_ interfaces)
which prohibit indirect configuration devices from receiving a softc
in their match routine that they can share with their attach routine.
* kill scc_tty[] and needs-count.
* Add usable-when-cold version of sccparam().
* Add pre-autconf() console initialization entrypoint.
* remove lint for gcc -Wall
* wbflush() -> tc_mb()
all but the last of which have been fed through cgd and committed to the
Alpha scc driver.
mips_r2000_, mips_R2000_ -> mips1_
mips_r4000_, mips_R4000_ -> mips3_
(which are also, for mnemonic reasons, consistent with gcc flag usage,
rather than using mipsI_ and mipsIII_).
Where CACHED_TO_HYS() is still needed for kernel-virtual-to-physical
or physical-to-uncached mapping (fb drivers), replace with
`#include <mips/cpuregs.h>'.
* dcparam() with normal tty t_param interface, which calls
* cold_dcparam() called with explicit dc7085 register address
and flags, which does the work and is also callable when cold,
to set up console (or kgdb) line parameters.
* Move mips-I pte (TLBlo) definitions from pmax/include/pte.h
to mips/include/mips1_pte.h
* Move mips-III pte (TLBlo) definitions from pica/include/pte.h
to mips/include/mips3_pte.h
* Add new mips/include/pte.h, which includes exactly one of
mips1_pte.h or mips3_pte.h (which still have namespace collisions),
depending on "options MIPS1" or "options MIPS3". (hack).
Move soft kvtopte(), ptetovk() definitions to mips/include/pte.h
* Add macro PTE_TO_PADDR() to hide the different hardware TLB formats
when mapping from pte to physical address.
* Add macro PTE_READONLY() to hide lack of SW read-only bit in mips-III
tlb. (mips1 pmap uses a sw bit in the PTE, mips3 looks up RO bit in
the kernel pmap.)
* Use macros (not direct TLB frobbing) in mips/trap.c, to make it
mips-1/mips-III indepenndet.
* Change {pmax,pica}/include/pte.h to just do #include <mips/pte.h>.
NetBSD-current changes:
* change include paths to be relative to the kernel-source tree
(e.g., `/sys') instead of arch/pmax/conf.
* add explicit options for exec packages (EXEC_ELF32, EXEC_ECOFF
for COMPAT_ULTRIX)
* comment out references to still-unsuppoted MI scsi.
DEC dc503 cursor chip) into Decstation 2100,3100 cfattach front-end
and ``machine-independent'' back-end.
pm_ds.c: pmin/pmax cfattach front-end
pm.c: bt478, 503 back-end
pmvar.h: declarations of back-end normal and console attach
entry points.
include files containing model-specific I/O device configuration.
Add more options and devices (ccd, LKM, etc), as appropriate for
documentation and as examples in a "template" GENERIC config file,
even though not all of these work completely yet.
from arch/mips/mips/locore.S to arch/pmax/pmax/locore_machdep.S.
* Move ARC-specific locore code (vmstat -i counters) to
arch/pica/pica/locore_machdep.S.
* When the mips3 locore support is known to work, both ports can now use
arch/mips/mips/locore.S.
wrappers for:
gets.c getenv.c strcat.c strcpy.c
so they compile again (if _KERNEL is defined).
For bootblock space reasons it would be prereable to call the PROM entrypoints
directly, via the macro wappers in de_prom.h, rather than C function wrappers.
* Create arch/mips/Makefile.inc with source list of generic MIPS-cpu
files for tags
* Use mips/Makefile.inc and updated tag list in pmax/Makefile
* Try building bootblocks in arch/pmax/stand.
consistency with the way machdep headers for other things are done.
(the creation of the ecoff_machdep.h files was done on the CVS server, to
keep the RCS logs intact.)
macros to use to remove #ifdefs from the machine ID case check.
Eventually, these headers will contain other information, e.g.
machine-dependent relocation information, etc.
use the pre-autoconfig cold serial-console inititialization entry
points from the bus-specific cfattach front-end code.
* Delete post-autoconfig code to switch from PROM output to kernel
driver for machines with dc serial chips.
cfattach front-end code:
dc_ds for the decstation 2100( pmin), 3100 (pmax), and 5100.
dc_ioasic for the decstation 5000/200 (3max) which does not have a
DEC TC-style IOCTL asic, but is configured as if it did.
* Add pre-autoconfig code initialization of kerenl dc driver console I/O
for remote serial consoles. The hack to use PROM serial I/O until the
dc device is autoconfigured is no longer necessary.
* Add MIPS make variable pointing at $S/arch/mips
* Build locore from $MIPS/mips locore source
* Build locore.o and fp.o (fp emulation) from arch/mips locore source
* Add target and rules to build pmax-specific locore code locore_machdep.o
from $PMAX/pmax/lcore_machdep.S
>* Use `-S' rather than `-x' to remove debugging symbols.
because the pmax toolchain and gcc disagree about what is a "local"
symbol, and ld requires a "-x" to let elf2aout build bootable a.out kernels.
mhitch