and with the comment '4.2BSD TCP/IP bug compat. Not recommended'
Add commented out 'TCP_DEBUG # Record last TCP_NDEBUG packets with SO_DEBUG'
(All hail amiga and atari which make some attempt to automate the
multiplicity of config files...)
option for System V semaphores. It appears that there are no overrides
in the code and each file has the following added.
options SYSVSEM # System V semaphores
+#options SEMMNI=10 # number of semaphore identifiers
+#options SEMMNS=60 # number of semaphores in system
+#options SEMUME=10 # max number of undo entries per process
+#options SEMMNU=30 # number of undo structures in system
options SYSVSHM # System V shared memory
If anyone thinks that this is incorrect for any of these files, please
correct it.
Note - the i386 port was not forgotten. It was done separately.
each vm_page structure. Add a VM_MDPAGE_INIT() macro to init this
data when pages are initialized by UVM. These macros are mandatory,
but ports may #define them to nothing if they are not needed/used.
This deprecates struct pmap_physseg. As a transitional measure,
allow a port to #define PMAP_PHYSSEG so that it can continue to
use it until its pmap is converted to use VM_MDPAGE_MEMBERS.
Use all this stuff to eliminate a lot of extra work in the Alpha
pmap module (it's smaller and faster now). Changes to other pmap
modules will follow.
- pmap_enter()
- pmap_remove()
- pmap_protect()
- pmap_kenter_pa()
- pmap_kremove()
as described in pmap(9).
These calls are relatively conservative. It may be possible to
optimize these a little more.
and use appropriately
- create more helper macros:
. cdev__xyz_init(c,n), such as cdev__ocri_init() for
/* open, close, read, ioctl */, etc.
. cdev__xRy_init(c,n), where nullop is used instead of enodev to dummy out
method `R' and the comments now read /* xxx (read) yyy */ instead
. cdev__xyz_t_init(c,n,t) - as per cdev__xyz_init, but sets d_type = t
as well
- use seltrue instead of dev_noimpl(poll,*), as (IIRC) cdevsw.d_poll should
always DTRT WRT returning a valid result. (a few devices previously
incorrectly returned ENODEV)
- use dev_noimpl(stop,enodev) instead of dev_noimpl(stop,nullop) if tty
== 0, because it doesn't matter if dev_type_stop isn't implemented in that
case, and it allows the use of the cdev__xyz_init macros. certain ports
(sparc,sparc64,x68k) used the nullop method for dev_type_stop in a few
drivers, whereas everything else uses enodev
- ensure that the comments are accurate WRT the behaviour of a given entry
rather than assigning to the whole field, set or clear individual flags,
which implies that the B_BUSY and B_INVAL flags will remain set.
this allows us to make the assertion in brelse() that B_BUSY is set,
which is the purpose of all this.
maps standard boot flags to corresponding RB_* values
use BOOT_FLAG() in port's MD code as appropriate
as discussed on tech-kern, add new boot flags -v, -q for booting
verbosely or quietly, and corresponding AB_VERBOSE/AB_QUIET
boot flags; also add FreeBSD-compatible bootverbose macro and
NetBSD-specific bootquiet macro
for hpcmips, use new bootverbose instead of it's own hpcmips_verbose
Tested on i386, and to limited extend (compile of affected files) also for
mvme68k, hp300, luna68k, sun3.
routine. Works similarly fto pmap_prefer(), but allows callers
to specify a minimum power-of-two alignment of the region.
How we ever got along without this for so long is beyond me.
abs