Use scc_tty_init() in scc_consinit(). Declare scc_consinit() in sccvar.h.
* Remove last vestige of special-case console handling in sccparam() code.
* Call scc_consinit() from findcons scc_serial() console-setup.
Dont PROM for scc serial console at all.
as pmax/dev/findcons.c:
* Follow the same logic: look for the device the PROM is using.
* If it's a framebuffer and we don't have a driver for it, try other
* framebuffers in PROM search order.
* If no match found, warn user and fall over to serial console.
* if no serial console found, go back to PROM.
Rework tc/scc.c attach routine to give cleaner initialization semantics.
Prune out old 'braindamage' code.
* Do rcons output properly, using cn_tab->cn_dev which points
at rcons cdevsw entrypoints.
* The pmadx console code was using keyboard (serial) device
(major,minor) for raster consoles with special code in the keyboard
drivers to catch output intended for consoles, pull it off the device
queue, and print them via cnputc().
Ifdef out RCONS_BRAINDAMAGE.
* Other minor cleanup to pmax scc driver.
tech-kern. Reported by Sean Davidson to cause erroneous doubling of
keyboard input on a 5000/50 under load.
Increasing the DELAY() from 2 to 30 doesn't help. Remove it for the
1.3 release. May cause problems with low-speed serial input, but
console keyboards work properly.
until a proper fix is available:
Perpetuate the 4.4bsd design even further. Change keyboard-driver
open routines to check for an active raster console. If active, set the
keyboard struct tty's t_winsize from the rcons t_winsize on first open.
See pr 4438 for remaining problems and discussion of a complete fix.
Add DDB interface to /sys/arch/mips/mips..
Rework heuristic stack traceback to work with DDB.
Add hooks to print exception log from DDB.
Add hooks from pmax console drivers: call Debugger()
after break from serial console, or 'DO' key from LK-xxx.
> revision 1.33
> date: 1997/05/15 02:15:55; author: thorpej; state: Exp; lines: +8 -4
> - In sccmatch(), check any user-specified offset, allowing scc unit numbers
> to be nailed down. From Ken Hornstein <kenh@cmf.nrl.navy.mil>, PR #3626,
> slightly modified to allow wildcarded offsets.
> - Blow away the cf->cf_unit check in sccmatch(); it's bogus.
Also gc usused references to NSCC and #include "scc.h"
* kill scc_tty[] and needs-count.
* Add usable-when-cold version of sccparam().
* Add pre-autconf() console initialization entrypoint.
* remove lint for gcc -Wall
* wbflush() -> tc_mb()
all but the last of which have been fed through cgd and committed to the
Alpha scc driver.
the IOASIC attached devices. The DS3100 will now configure properly.
Fix the DS5000/25 IOASIC table entry for the RTC so the RTC interrupts
get enabled.
Fix up a moved include file.
- split softc size and match/attach out from cfdriver into
a new struct cfattach.
- new "attach" directive for files.*. May specify the name of
the cfattach structure, so that devices may be easily attached
to parents with different autoconfiguration semantics.
code. Substantially the same code tested on a 5k/240. Should work on a
5k/1xx. Not tested on a MAXINE, where the single unit may break the
PROM-channel-number to driver-channel-number mapping.
Rename the ioctl asic register and slot macros from ASIC_<xxx> to
IOASIC_<xxx>, to be compatible with the machine-indpendent names in
sys/dev/tc/ioasicvar.h. The pmax code still uses
sys/arch/pmax/pmax/asic.h, as some of the registers and offsets
defined there are not yet defined in sys/dev/tc/ioasicvar.h.
Rename the ioctl asic base-address pointer from `asic_base' to `ioasic_base'.
independent TC support in sys/dev/tc/tc.c and sys/dev/tc/tcvar.h:
* Change the tc autoconfiguration tables to use a struct tc_attach_args
instead of the ad-hoc structure.
* Change all pmax device drivers to use a `struct confargs' that's
assignment-compatible with sys/dev/tc/tcvar.h `struct tcdev_attach_args'.
Devices that can be present on a TC or as ioctl asic/mainbus builtins
use the same `struct confargs'.
* Eliminate the `BUS_CVTADDR()' macros which the pmax port inherited from
an old, now-obsolete sys/arch/alpha snapshot.
* Update the comments and debugging code in interrupt handlers to
be consistent with the machine-independent TC support.
Other commits that overlap the same source files include: re-enabling
clock-tick interrupts earlier, and counting hardclock ticks for vmstat -i.
Add as-yet-unused speed entries for a 1x SCC clock, up to 200 Kbits.
Remove old top-bit-means-delay code, since nothing seems to need it,
and it apparently partially broke lk-201 initialization anyway.
both off, haracters with their top bit clear were interpreted as a delay.
This (strange) behaviour is still available if SCC_PARITY_MEANS_DELAY
is defined.
