multi-channel driver), or to SCSI_CHANNEL_ONLY_ONE if a
single-channel driver.
(2) use scsiprint() rather than a locally-defined autoconfig print
function, and kill any locally-defined print function.
(2) in scsibusmatch, match channel as appropriate.
(3) add a scsiprint() function, to do the "scsibus at..."
and channel (if not SCSI_CHANNEL_ONLY_ONE) printing,
i.e. the common functionality that all SCSI drivers currently
should be doing.
a char *, because that's what was really intended, and because
if the print function modifies the string, various things could become
unhappy (so the string should _not_ be modified).
Fix so that resource wait queueing works.
Changed all functions to take a pointer to uba_softc instead of unit
number, except for ubareset(). This must be done later.
the lowest bit set. This isn't any more or less valid according to the PCI
spec, but it deals with lame devices that don't implement all of the top
bits.
a boot string for firmware that can do this, such as the SPARC and
the sun3 models. It is currently silently ignored on all other
hardware now, however. The MD function "boot()" has been changed to
also take a char *.
values, i.e. 0xfffffffe and 0xffffffff respectively. The changed
definitions were incorrect, according to the PCI Local Bus Specification
(Revision 2.0). Further rationale and a workaround for the broken
devices that instigated the change provided in a message to
current-users@netbsd.org, dated Mon, 05 Aug 1996 22:06:58 -0400,
message ID 16773.839297218@ux2.sp.cs.cmu.edu>.
- In egstart(), if the Send Packet command fails, m_freem()
the mbuf chain before dequeueing another one (memory leak).
- In egintr(), return 1 if a known interrupt was processed.
Would manifest itself as spurious interrupts.
- adjust txhiwat and mindma params a bit
- fixed a couple of incorrectly labeled panic calls
- the "location" was being calculated incorrectly in some cases (forgot
to subtract off MID_RAMBASE). this only caused problem when trying
to change the size of the tx/rx buffers (e.g. to 64KB).
- fixed possible non-aligned DMA burst in the starting byte burst case.
(e.g. if we could DMA 3 bytes, but only have 2 it is not legal
for us to use MIDDMA_BYTE2 mode).
- opt: on tx: try and avoid flushing the internal buffer by padding out the
length of the last mbuf a bit (if possible)
- merged multiple DRQ/DTQ ADD macros into a single DRQ and a single DTQ
macro with a uniform interface to make the code simpler and easier to read.
- en_start: only update atm_flags if EN_MBUF_OPT is enabled (which it
should be)
- for alburst: make sure we don't DMA more bytes than we need (on both
tx and rx). if the alburst is larger than we need, drop to
MIDDMA_WORD mode.
- major change: enable the use of byte and 2 byte DMA on the trasmit side.
this allows us to DMA from non-word sized/aligned mbufs directly.
[the old code would always call en_mfix which would copy (or move) the
data in order to ensure proper alignment... it turns out TCP gives
us non-word sized/aligned mbufs when it is retransmitting, so we needed
to handle this case more efficiently.] the following functions
were changed to make this work:
- en_dqneed: add an arg to let us know if we are transmitting or not.
if we are TX, then we must take into account byte DMAs when
estimating the number of DTQs we will need for a buffer
- en_start: only mfix mbufs if DMA is disabled
- en_txdma: only set launch.nodma if we have en_mfix'd the mbuf chain
also, we may need a DTQ to flush the chip's internal byte buffer
- en_txlaunch: only attempt a copy if we have the proper alignment.
add byte dma code for the front and end of the buffer.
make sure the internal dma buffer is flushed out.
- stats: keep track of how many times we have to use byte sized DMA
midwayreg:
- add byte/2byte DMA defines
midwayvar:
- add new stat counter to monitor less-than-word lengthed DMA
mycroft