f6ffe73a99
Add Yet Another Broken CD-ROM Drive to The List.
...
From Lennart Augustsson <augustss@cs.chalmers.se>, PR #2971 .
1996-11-29 19:51:14 +00:00
f0873310e2
Another quirky cdrom drive ; pr kern/2917
1996-11-08 05:06:55 +00:00
19bb57bc5a
Add another broken CDROM. Fixes PR kern/2913.
...
Some misc. cleanup.
1996-11-06 05:50:31 +00:00
c53ad1988a
* At least the Teac FC-1 Shugart-SCSI bridgeboard does motor on/off
...
management by itself. But when it gets a start unit request, it keeps
the floppy motor running all the time. This adds code for dealing with
yet another quirk (SDEV_NOSTARTUNIT) that prevents sd.c from sending
start unit requests. A entry for the Teac FC-1 is added to the quirk
table.
1996-10-23 07:25:39 +00:00
efccf77947
Add quirk entries for two more optical drives; closes pr kern/2861
1996-10-18 17:22:17 +00:00
9a2c8cf28c
revert previous kprintf change
1996-10-12 23:23:13 +00:00
9beb92aad7
printf -> kprintf, sprintf -> ksprintf
1996-10-10 23:32:59 +00:00
01d75c7c68
- printf -> kprintf, sprintf -> ksprintf
...
- make this compile cleanly.
1996-10-10 23:31:40 +00:00
d5bc24be7a
- printf -> kprintf, sprintf -> ksprintf
...
- replace sequences of sprintf(p, ...); p += strlen(p) with p += sprintf(p,
1996-10-10 23:30:58 +00:00
b9c06e6fa3
dev/microcode/aic7xxx/aic7xxx.seq,
...
dev/microcode/aic7xxx_seq.h,
dev/ic/aic7xxxreg.h:
Remove intrinsic knowledge about SDTR and WDTR messages and replace it
with a generic message system that allows the kernel driver to handle
SDTR, WDTR and any other type of extended message it chooses too. This
makes the sequencer code much simpler, makes extended message handling
debuggable since the bulk of the work is in the kernel driver, and saves
lots of instruction space.
Regen microcode header file.
dev/ic/aic7xxx.c, dev/ic/aic7xxxvar.h:
Add code to handle WDTR and SDTR negotiation in light of the changes in
the message interface to the sequencer. Don't reject targets that
negotiate async by sending an SDTR with a 0 offset. Use an sdtr message
with 0,0 to negotiate async when a target suggests a period that is too
long for us to handle. Some tape and cdrom drives don't like us doing
the message reject that we did in the past.
Fix a problem with handing the QUEUE FULL condition.
Fix a race condition (most likely the cause of the SCB paging problems) that
might allow the sequencer to get unpaused before the condition that caused
it to be paused (a SEQINT) was handled.
Race condition pointed out by Doug Ledford <dledford@dialnet.net> and
by "Dan Willis" <dan@plutotech.com>.
dev/pci/ahc_pci.c:
Add support for the 2940AU, an aic7860 based controller.
dev/pci/pcidevs.h, dev/pci/pcidevs_data.h:
Add product IDs for the 2940AU, aic7860 and aic7855.
Regen data file.
scsi/scsi_message.h:
Add MSG_EXT_SDTR_LEN and MSG_EXT_WDTR_LEN - the length of bytes in these
extended messages.
Thanks to Chuck Cranor <chuck@maria.wustl.edu> for testing these changes
out for me.
1996-10-08 03:04:02 +00:00
d3f587e135
For ioctl commands which may change the device's state, ensure that
...
the caller has the device open for writing.
1996-09-18 02:34:31 +00:00
fcde57a426
For ioctl commands which may change the device's state, ensure that
...
the caller has the device open for writing.
1996-09-13 00:35:59 +00:00
9aeee9fb17
Remove a couple of opcodes that are already (and more appropriately)
...
defined in scsi_changer.h
1996-09-12 01:57:17 +00:00
f60341a382
Store the SCSI version in the scsi_link, and set the LUN in the CDB
...
if the version is <= SCSI-2. This should help some older SCSI
devices that previously needed the "NOLUNS" quirk. While this is
not strictly necessary on SCSI-2 devices, the spec allows it,
so we set it for SCSI-2 devices "just in case". See section 7.2.2 of
Draft X3T9.2 Rev 10L for details.
1996-09-03 18:20:31 +00:00
11ec3588ad
(1) add a 'channel' field to scsi_link.
...
(2) in scsibusmatch, match channel as appropriate.
(3) add a scsiprint() function, to do the "scsibus at..."
and channel (if not SCSI_CHANNEL_ONLY_ONE) printing,
i.e. the common functionality that all SCSI drivers currently
should be doing.
1996-08-28 18:47:51 +00:00
2a73ef60b7
change cfprint_t type definition to take a const char *, rather than
...
a char *, because that's what was really intended, and because
if the print function modifies the string, various things could become
unhappy (so the string should _not_ be modified).
1996-08-27 21:53:46 +00:00
c87188f1bd
be quiet about read_subchannel. Some CD players use this to poll, and having
...
a screen filled with kernel messages isn't nice. Closes pr kern/817
1996-08-13 08:55:38 +00:00
5c3b7a7213
Fix condition where disk_unbusy may not get called
1996-08-13 08:31:31 +00:00
27e2d3eee3
Match any Maxtor XT-8760S for the SDEV_NOLUNS quirk. Some of these
...
drives carry Sun OEM identifiers, as well.
Noticed by Taras Ivanenko <ivanenko@ctpa03.mit.edu>.
1996-07-24 20:50:23 +00:00
a7efb38d4c
Some MUSTEK scanners fill the vendor string in the SCSI identify
...
string with 0xFF instead of 0x20. Shorten the compare to 6 bytes to
take care of this.
Fixes PR #2617 by myself, which is based on a private problem report
by Neil Brewitt.
1996-07-12 16:49:50 +00:00
9c8111508d
Add SCSI_QUEUE_FULL ; part of pr port-i386/2600
1996-07-10 22:48:56 +00:00
228f4739ce
add ZIP quirk for SDEV_NOMODESENSE
1996-07-05 21:58:04 +00:00
7e1c82f6f4
- Apply PR/2535: Add support for flex scsi disks.
...
- Add a quirk called SCSI_NOMODESENSE for drives like the iomega jaz,
that don't support mode sense.
1996-07-05 16:19:02 +00:00
56543dfb7d
In sddump(), don't check the SDEV_MEDIA_LOADED bit of the device, since
...
that bit might have been cleared by successful unmounting of all filesystems
on the dump device, e.g. in the case of "reboot -d".
1996-06-04 23:12:14 +00:00
a0be48ca23
Implement ST_Q_UNIMODAL quirk, which indicates that a drive will reject
...
all attempts to mode select, even if the attempted mode is supported.
Add the ST_Q_UNIMODAL quirk for the HP Colorado T4000s which exhibits
this behavior. (Someone please lob a tactical nuke in that direction.)
From David Rosenthal <dshr@vitria.com> on netbsd-bugs.
1996-05-24 02:04:29 +00:00
a7136623a9
Added prototypes for inline functions atoi() and strchr().
1996-05-18 22:58:01 +00:00
e03577c2a4
Slight adjustments for new version of ahc driver.
1996-05-16 04:00:58 +00:00
153c617719
Clear SDEV_MEDIA_LOADED bit on the last close of a device. This causes the
...
geometry info & the disklabel to be reloaded on each 'first-open' of the
device.
1996-05-14 10:38:47 +00:00
1379322cde
Print the error code in the "not queued" message, to make debugging
...
a bit easier, and make sure a newline gets printed.
1996-05-14 00:10:37 +00:00
7f0f603f3a
Bug fixes from PR 2329, plus a few from me.
1996-05-11 22:21:51 +00:00
0efbe64fb8
Cleanup the rest of the SCSIDEBUG printfs. From Bernd Ernesti.
1996-05-05 19:52:50 +00:00
88c3808921
- SCSIDEBUG printf() fixes.
1996-05-03 19:48:20 +00:00
c4b8477b78
Added another quirked SCSI device, re PR 2320 from Manuel Bouyer
1996-05-02 01:09:01 +00:00
ffd5576439
remove include of <sys/cpu.h>
1996-04-22 01:44:31 +00:00
3c0096ff79
gcc -Wall delinting: unused variables, assignments inside if's and missing
...
arguments in printf statements.
1996-04-19 00:02:29 +00:00
52fee18c6f
New SCSI media changer driver, written from scratch by me. Some
...
influence from the old driver (written by Stefan Grefen) and from
an autochanger driver written by the Systems Programming Group at the
University of Utah Computer Science Department (currently residing
in src/sys/arch/hp300/dev/ac.c).
1996-04-03 00:25:21 +00:00
94d26d3017
- Eliminate scsi_conf.h
...
- Fix prototypes
- Fix PR/2248 [Problems with HP scanjet...]
1996-03-30 21:47:00 +00:00
beec8ba94c
Eliminate scsi_conf.h.
1996-03-30 21:44:50 +00:00
1180bee580
eliminate unused variables.
1996-03-29 14:50:12 +00:00
4b535677ab
fix pasto: sdminphys -> cdminphys in comment.
1996-03-27 01:11:41 +00:00
f20498187e
SDUNIT -> CDUNIT in last.
1996-03-27 00:48:50 +00:00
5ed22a9852
Put back dk_establish() for now.
1996-03-26 22:22:19 +00:00
5f57f43753
Increase *OUTSTANDING.
...
Remove old dk_establish() garbage.
Support the `ancient' bit in both drivers.
1996-03-26 20:32:06 +00:00
caeb897758
Fix trivial oversight in last.
1996-03-24 07:36:11 +00:00
3166ff9f2f
Add a SDEV_NOLUNS quirk for the Epson OMD-5010 removable MO cartridge drive.
1996-03-21 03:29:40 +00:00
e819063285
Define a full set of [234][bl]tol() and lto[234][bl]() conversion functions,
...
inlined.
Use sized types in protocol structures.
Make the definition of scsi_sense_data less ugly.
1996-03-19 03:05:15 +00:00
9785218963
Fix for NEC D3847 1.6gB drive which reported itself at lun[1-7].
1996-03-18 16:19:58 +00:00
12bcc82160
Parentheses are your friends.
1996-03-17 02:06:50 +00:00
532e997971
New device attachment scheme:
...
- split softc size and match/attach out from cfdriver into
a new struct cfattach.
- new "attach" directive for files.*. May specify the name of
the cfattach structure, so that devices may be easily attached
to parents with different autoconfiguration semantics.
1996-03-17 00:57:14 +00:00
8f4177ba60
Add another broken drive that doesn't deal with LUNs properly to The List.
...
Fixes PR 1961, from Kevin P. Neal.
1996-03-05 01:45:42 +00:00
a8573feb51
Normalize SCSI autoconfiguration output.
...
From Chris Demetriou <cgd@NetBSD.ORG>. Fixes PR #1958 .
1996-03-05 00:15:09 +00:00
ad355be572
Add a SDEV_AUTOSAVE quirk for the DEC RZ55.
1996-02-22 23:37:27 +00:00
91e913b297
Handle EOF a little differently.
1996-02-19 00:06:07 +00:00
c5326f656e
Change variable name to avoid GCC warning.
1996-02-18 23:21:48 +00:00
2dfda50bb9
Minor tweak; make sure window size is 0 on close.
1996-02-18 20:44:40 +00:00
8f0f40e8b3
Missed some prototyping foo.
1996-02-18 20:41:18 +00:00
342c383728
Truncate to the window size in ssminphys(), not ssread().
1996-02-18 20:38:44 +00:00
294879d4ee
Add SCSI scanner support by Kenneth Stailey and Joachim Koenig-Baltes,
...
hacked a bit. Needs more work.
1996-02-18 20:32:40 +00:00
23726708b0
Minor change.
1996-02-18 20:30:53 +00:00
45eee6c55b
remove #ifdef notdef made unnecessary by previous changes (PR#1597)
...
put in missing "if (error)" that caused tape IO to always fail.
(closes PR#2086)
1996-02-17 16:00:22 +00:00
0bc63f486d
scsi prototypes
1996-02-14 21:46:52 +00:00
f18f32d2e1
PR#2048. Prototype st_erase().
1996-02-09 14:51:34 +00:00
e5ece749b2
Handle COMMAND ABORTED by forcing a retry. PR#2003, but with some more
...
diagnostic info.
1996-01-31 15:16:06 +00:00
919f6728ab
Accept DIOCEJECT as a synonym for CDIOCEJECT. Implement DIOCLOCK
...
separately from CDIOCALLOW and CDIOCPREVENT, even though they perform
basically the same function (with a different interface XXX).
1996-01-30 18:28:02 +00:00
c7a20f0ee3
Implement DIOCLOCK and DIOCEJECT. DIOCEJECT is limited to removable
...
media. Fixes PR #1975 .
1996-01-30 18:24:47 +00:00
8068d9eeb2
Handle cases like the following:
...
- controller calls scsi_done() with error XS_TIMEOUT
- scsi_done() calls sddone()
- sddone() calls disk_unbusy()
- scsi_done() calls controller to retry command (missing the
call to disk_busy())
- controller calls scsi_done()
- scsi_done() calls sddone()
- sddone() calls disk_busy(), which panics because of the imbalance.
Bug noticed by Leo Weppleman, who also suggested this fix; pass an additional
boolean argument ("complete") to the device's "done" routine, with a
value of `0' passed from the previous call to "done", and add an additional
call to "done" when the xfer resources are freed.
1996-01-12 22:43:26 +00:00
59dd89e3b1
LUN deficient device: Tandberg 3600 (Ken Raeburn; PR#1933).
1996-01-12 11:32:37 +00:00
5b51ec5cc8
Honor cache request and implement erase command, and add the SCSI tape
...
device configuration page. Fixes PRs 807, 1201, and 1705.
From John Kohl <jtk@kolvir.blrc.ma.us>.
1996-01-11 03:36:34 +00:00
5b39541e48
New generic disk framework. Highlights:
...
- New metrics handling. Metrics are now kept in the new
`struct disk'. Busy time is now stored as a timeval, and
transfer count in bytes.
- Storage for disklabels is now dynamically allocated, so that
the size of the disk structure is not machine-dependent.
- Several new functions for attaching and detaching disks, and
handling metrics calculation.
Old-style instrumentation is still supported in drivers that did it before.
However, old-style instrumentation is being deprecated, and will go away
once the userland utilities are updated for the new framework.
For usage and architectural details, see the forthcoming disk(9) manual
page.
1996-01-07 22:01:38 +00:00
0548b8e5ad
SCSI sense `info' field is a signed value (from John Kohl; PR#1597).
1996-01-05 16:03:35 +00:00
19c3f6d999
Add another broken CD-ROM drive to The List (Chinon CDS-525), per PR #1686 .
...
From Kortelainen Mika <k125374@cs.tut.fi>.
1995-12-31 02:40:53 +00:00
89f8e05c10
Trim NULs, in addition to spaces, in scsi_strvis().
1995-12-11 04:43:01 +00:00
1cd2ca323b
Remove a couple of now unneeded assignments.
1995-12-07 21:54:24 +00:00
b6c6d46a82
In sdminphys(), add a comment about the semantics of the "length" field
...
in a 6-byte read/write cdb (namely, length == 0 really means 256), and
that we handle this conservatively by limiting the transfer to 255 blocks.
*sigh* One just never knows how a pre-scsi-1 device is going to behave.
1995-12-07 19:46:00 +00:00
c9895db015
In both cd.c and sd.c:
...
If the read or write request can fit into a 6-byte cdb, then
use a 6-byte cdb, otherwise use the 10-byte as before.
In sd.c:
In sdattach(), make a note if the device is "ancient" (i.e.
inqbuf.version & SID_ANSII == 0).
Implement sdminphys(): if the device is "ancient", shorten the
transfer so it will fit into a 6-byte cdb.
These changes have eliminated the rejected read/write requests on my
Sun 3/60 with 2 ESDI disks behind an Emulex MD21.
1995-12-07 19:11:32 +00:00
7a7ca00077
Add quirk for Exabyte 8200/rev. 263H (from Paul Goyette; PR#1797).
1995-11-30 10:12:04 +00:00
fbecb8d22b
Remove the gratuitous code to check for a disc at boot time.
1995-11-11 20:07:57 +00:00
8d78a257c0
More rogues.
1995-11-01 01:15:07 +00:00
cbef9e5129
Add missing spindle synch control, rotational offset, and RPM members
...
to the rigid geometry mode page. These missing members are at the
end of the page, in space wich was previously marked "reserved".
1995-10-15 23:32:02 +00:00
444e2789c6
Add quirk entries for Wangtek SCSI tapes. Also, add entry for
...
Tandberg 3800 (fixes PR#1592 - from Jochen Pohl).
1995-10-13 20:01:03 +00:00
92221a1399
Return EINVAL if something other than a whole number of blocks is requested.
1995-10-10 02:52:56 +00:00
db0107b895
Specify SCSI_DATA_OUT in sddump() (from John Kohl; PR#1482).
1995-09-30 22:57:19 +00:00
b93138b93d
Add another broken NEC CD-ROM drive to The List. Fixes PR #1451 .
1995-09-26 23:37:50 +00:00
249cddaaa7
Don't declare Debugger(). It's handled in <sys/systm.h>.
...
#include <sys/systm.h> where necessary, as suggested by Jonathan Stone.
Fixes PR #1511 .
1995-09-26 19:26:48 +00:00
d9e37f2bc7
Set the scsi link before calling config_attach(), so target/lun info is
...
available to, say, dk_establish().
1995-08-21 09:30:09 +00:00
3560df43af
CHINON CDS-535 version Q117 also needs NOLUNS. Assume all 535s do.
1995-08-14 13:01:42 +00:00
19f3c3099f
Another SDEV_NOLUNS device from paul@pgoyette.bdt.com (Paul Goyette).
1995-08-13 17:48:57 +00:00
8887de9230
opri --> s
1995-08-12 22:58:01 +00:00
8a9880e714
Fix oversight in previous.
1995-08-12 21:36:46 +00:00
80d7b0695a
minphys() functions really should return void.
1995-08-12 20:30:45 +00:00
92637a6d42
Add another Seagate disk to the list, and make all the disks match any
...
firmware revision.
1995-08-06 00:04:00 +00:00
24a5e56396
Use an intermediate variable to shorten label initialization code.
1995-08-05 23:47:52 +00:00
d8e7ea659c
restore a deleted semicolon
1995-07-24 09:03:00 +00:00
4d0bd10d53
kill structure offest comments in non-fixed-size structures.
...
In some of our worlds, pointers just Aren't 4 bytes.
1995-07-24 07:08:14 +00:00
3301cf82fd
update SCSI minphys routines' definitions to match standard minphys()
...
definition and usage.
1995-07-24 06:55:37 +00:00
0b469d4a12
add/change a few quirks:
...
(1) all Chinon CDS-431 CD-ROMs (regardless of revision)
are forced to only having LUN 0, at the suggestion
of Michael Hitch.
(2) _force_ searching of extra LUNs for the Emulex MD21/S2
ESDI bridge. It's pre-SCSI 1, but knows about LUNs.
"amazing." From Jason Thorpe.
(3) recognize an Emulex tape adapter in front of a QIC-36
tape, and have it forced to only LUN 0. This is
an odd one; vendor, name, and rev strings are all
spaces. Anything that mathes this is very likely
broken, anyway, so might as well give it a shot.
Again from Jason Thorpe.
1995-07-12 09:56:09 +00:00
d8fe81c04c
implement SDEV_FORCELUNS flag, as suggested by Jason Thorpe.
1995-07-12 09:43:29 +00:00
f60db5f02a
add a SDEV_FORCELUNS flag, as suggested by Jason Thorpe, to force
...
the SCSI code to look for LUNs on prehistoric (pre-SCSI 1) drives &
controllers, where normally it would not.
1995-07-12 09:42:00 +00:00
5b671ea6a8
Morningstar SnapLink -> SDEV_NOLUNS, per Peter Galbavy in pr 1192.
1995-07-09 09:44:57 +00:00
21b6db23b7
play the alphabetization game
1995-07-09 09:43:07 +00:00
5a5eb678c9
QUANTUM P105S 910-10-94x A.3 -> SDEV_NOLUNS
1995-07-09 09:30:42 +00:00
7263209ce6
Make each disk and tape driver define its own read and write functions.
...
Deprecate rawread() and rawwrite() completely. Remove d_strategy from cdevsw to
force the abstraction barrier.
1995-07-04 07:15:28 +00:00
1c5d265cad
another CD-ROM quirk, a la PR 1166
1995-06-27 20:42:45 +00:00
2a8d6461a8
implement new-style block device dump routine if __BDEVSW_DUMP_OLD_TYPE
...
not defined, otherwise use an "not implemented" stub.
1995-06-26 05:16:55 +00:00
d093e5d8b8
make dump stubs consistent
1995-06-26 05:15:33 +00:00
d8264613c8
add entry for another tweaked Texel CD-ROM. from pr 1151
1995-06-24 01:22:30 +00:00
6664ae1ddd
Add another CD-ROM drive to The List.
1995-06-18 05:13:09 +00:00
7d18c2534d
Add `Maxtor LXT-213S', this time without a Sun OEM addition.
1995-06-02 21:44:11 +00:00
011aa68805
looks like some extra ')'s were left in here.
1995-05-03 21:38:57 +00:00
1d2f0bce2a
Make the byte-shifting code consistent.
1995-05-03 19:38:45 +00:00
224a7f4533
config.new description of SCSI mi files.
1995-04-17 07:15:40 +00:00
04e937dcbd
Don't boundary check I/O to the `raw' partition.
1995-04-15 05:01:26 +00:00
68c8c80929
kernel_pmap --> pmap_kernel()
1995-04-10 16:48:27 +00:00
3836533fc6
Add another broken CD-ROM drive to The List.
1995-04-04 05:44:32 +00:00
7e2dabf972
Add a missing unlock.
1995-04-01 10:29:41 +00:00
1d568eab9a
Revamp the locking mechanism slightly.
1995-03-29 23:04:39 +00:00
b51403f60d
Remove the write protect check altogether, and rely on the drive to do it.
1995-03-25 19:45:18 +00:00
12a1b9ad67
Add a rogue entry for the ANRITSU DMT780.
1995-03-25 18:41:42 +00:00
911fbf48fa
fix syntax error. Andreas Gustafsson <gson@clinet.fi>
1995-03-24 20:17:15 +00:00
990077ba88
Don't bother with DIOCWLABEL.
1995-03-23 12:13:37 +00:00
06d0a67a07
Check for read-only media in open(), not write().
1995-03-23 12:11:07 +00:00
d21add8356
Revert cdsize() to do nothing.
1995-03-23 11:51:22 +00:00
4712cd33dc
Rearrange DIOCWDINFO a little; closer to wd.c.
1995-03-23 11:43:09 +00:00
562ca7760b
Fix typo.
1995-03-23 11:37:51 +00:00
02df08a47e
Allow DIOCWDINFO even if label is not `writable'.
1995-03-23 11:33:18 +00:00
e203e49ef5
Correct spelling of `fictitious'. Add patterns for optical memory devices.
...
From Alistair Crooks.
1995-03-07 21:46:06 +00:00
2986fc2fd0
Be less picky about revision numbers for some broken devices.
1995-02-22 19:32:33 +00:00
e560d77223
Another Maxtor botch.
1995-02-09 10:23:14 +00:00
d8743f51a2
Add Exabyte 8200 to the list.
1995-02-01 09:37:54 +00:00
52bacd79d6
Fix invocation of scsi_scsi_cmd(), per John Kohl.
1995-01-30 15:54:42 +00:00
1076165d07
All revisions of the TDC 3600 are rogues.
1995-01-30 15:39:33 +00:00
7639253b70
Finish last change.
1995-01-30 11:50:23 +00:00
321b00bd07
Some drives don't grok START with LoEj=1, either.
1995-01-30 11:47:56 +00:00
0ece1143f6
Set the LoadEject bit when issuing a START.
1995-01-30 11:37:17 +00:00
9085638020
Some devices really do require the START before the PREVENT. This makes no
...
sense.
1995-01-30 11:34:25 +00:00
1611df6ae0
Update copyrights.
1995-01-26 12:05:49 +00:00
b76a328caa
Redo the `wait for spin up' code. The Mach 3 method clearly doesn't work.
...
Also, rearrange the first open sequences a bit; SDEV_OPEN is no longer magic.
1995-01-26 11:56:51 +00:00
726fa4e94f
Do the PREVENT before the START.
1995-01-23 18:17:22 +00:00
feb5b29596
Remove old, misleading comment.
1995-01-23 17:56:26 +00:00
a6e7fe0d2a
If the disk reports a block size of 0, assume it really meant 512.
1995-01-16 21:40:17 +00:00
4a1e51751b
Trivial simplification.
1995-01-16 21:34:10 +00:00
e71e917e9d
Remove unused macros.
1995-01-16 21:31:34 +00:00
85532dd4ce
Don't clear the debug flags when copying the prototype scsi_link.
1995-01-16 21:13:40 +00:00
28775a6a5d
Add a DIAGNOSTIC check.
1995-01-13 14:38:13 +00:00
7650bd97fc
Always boundary check I/O.
1995-01-13 10:46:32 +00:00
83a1c4799e
Add two more broken devices.
1995-01-12 10:25:44 +00:00
dff292c275
Put Dan's broken tape drive in The List.
1995-01-01 11:37:03 +00:00
bfd9901daf
Fix some oversights in the debugging code.
1994-12-30 05:33:06 +00:00
d78ddddef6
Update the rogue entry for ancient drivers to match reality.
1994-12-30 05:23:49 +00:00
6e9d6a0d75
And a little better...
1994-12-30 05:20:22 +00:00
0a83cd8c57
Deal with short inquiry response a little better.
1994-12-30 05:14:52 +00:00
5d3bd57538
Fix a couple of things in the sense printing code.
1994-12-29 13:49:57 +00:00
f2909dc62b
Increase the st_space() timeout.
1994-12-28 19:55:50 +00:00
8fd135209c
Numerous changes. Many bugs fixed, better autoconfig, a few new features.
1994-12-28 19:42:47 +00:00
3e7afdbe8a
Remove DIOCSBAD handling. It's not actually handled, so why recognize it?
1994-12-16 04:38:30 +00:00
ca65f2ce5d
Remove dkbad.h.
1994-12-14 15:17:22 +00:00
1b372b7e96
Remove some redundant code.
1994-12-01 13:07:28 +00:00
0109779d43
Remove unneeded override of SCSI_NOSLEEP.
1994-12-01 12:45:25 +00:00
c1cbd9c635
Set UIO residual count.
1994-12-01 12:36:35 +00:00
71ab8bb627
Always set the device number correctly, even though we don't need it.
1994-12-01 12:26:37 +00:00
d18cbacd88
Redux.
1994-12-01 12:12:08 +00:00
1066219897
Uncomment call to scsi_user_done(), and remove a duplicate biodone() (and
...
another si_free()).
1994-12-01 12:04:43 +00:00
a10cbd7179
Remove the silly statically allocated array, and simply malloc the data
...
structures as needed. Also, put the buf in the malloc()ed area. Remove a
duplicate si_free() (though this was harmless before).
1994-12-01 11:53:56 +00:00
cc44b4600c
There's no point in bothering to unlock what we didn't lock.
1994-11-23 07:54:15 +00:00
95edd299b0
Add still more locking.
1994-11-22 03:23:49 +00:00
284d17e8f0
Complete last change.
1994-11-22 00:14:24 +00:00
0c36dd6762
C botch repair from bostic
1994-11-22 00:05:36 +00:00
c81c637ee3
Return EIO when the drive is empty.
1994-11-21 11:37:26 +00:00
7a1dcbfac6
Clean up open and close routines somewhat.
1994-11-21 11:28:47 +00:00
fd32202948
Replace dev_unit with device_softc in scsi_link. Change argument to foostart()
...
to void*.
1994-11-21 10:39:09 +00:00
5bd4115690
Add some missing locking, and some general cleanup.
1994-11-20 22:36:43 +00:00
38483bbbf0
Enough Chinese torture already
1994-11-15 23:00:23 +00:00
d8561ad477
Oops; update scsibusmatch() arg list.
1994-11-03 22:09:00 +00:00
ef0c18e1cf
Always use direct configuration for SCSI devices.
1994-11-03 22:05:08 +00:00
54608f7ea0
Remove a couple of i386-specific hacks, and make a couple of others #ifdef
...
CONFIG_INDIRECT instead.
1994-11-03 20:24:21 +00:00
6ac2bbfc35
be more careful with types, also pull in headers where necessary.
1994-10-30 21:43:03 +00:00
28cbceeec7
Make this more likely to work.
1994-10-23 19:24:01 +00:00
e5d974c51f
First cut at making user-level SCSI commands work. This is untested.
...
Partly from John Brezak.
1994-10-20 20:31:23 +00:00
b8ab5f65d1
Back out change to print geometry from label at boot; can't do this reliably.
1994-10-20 16:54:44 +00:00
7d391c250d
Fix minor omission.
1994-10-20 14:10:18 +00:00
cd66683989
openpart -> openmask
1994-10-20 14:08:07 +00:00
bb12b9c8a2
Trivial stylistic changes.
1994-10-20 14:05:08 +00:00
caaeda044b
Similar changes to sd.c.
1994-10-20 14:03:38 +00:00
b1568d887e
Use the block size in the label in most cases.
1994-10-20 13:50:38 +00:00
d5b3572f5c
Various changes:
...
* Get rid of unused `partflags'.
* Use dk_openpart, and remove `openparts'. Also, allow an open on both
the block and characters devices at the same time.
* If there was a label, print the geometry from the label at boot time.
* Turn `wlabel' into a flag, and *don't* set it automatically in
DIOCWLABEL; disklabel(8) does that.
Other minor changes.
1994-10-20 13:33:36 +00:00
49c34d3337
move arch dependence to archs. clean up a bit. deal with weird MAXPARTITONS.
1994-10-14 18:26:22 +00:00
5aa2f1e6bb
remove an un-aligned access
1994-08-30 17:01:57 +00:00
692c724215
un-aligned access is not cool on some processors
1994-08-12 08:57:18 +00:00
da79c879cd
On probe or open, retry the READ CAPACITY once if the drive reports NOT READY.
1994-08-11 23:51:26 +00:00
3e685aec5c
Change ST_Q_NEEDS_PAGE_0 to something more generic.
1994-08-09 18:50:17 +00:00
558c00c001
Fix spelling of `STEREO'.
1994-08-05 22:56:19 +00:00
b5c5c47f92
Obey the command queue size for the controller.
1994-08-04 09:52:47 +00:00
863c736e39
Normalize label handling.
1994-07-26 19:39:19 +00:00
b10a5d5fac
change to support other MAXPARTITIONS vals aside from 8
1994-07-04 20:39:46 +00:00
fd7c79353e
knf
1994-06-29 23:32:42 +00:00
fccfa11af5
New RCS ID's, take two. they're more aesthecially pleasant, and use 'NetBSD'
1994-06-29 06:39:25 +00:00
72679b6801
Fix a comment.
1994-06-19 03:29:37 +00:00
7d3285c3d4
resolve confusion over who owns the buf after calling scsi_scsi_cmd()
1994-06-16 15:57:39 +00:00
a69dd750a2
b_un.b_addr -> b_data
1994-06-16 01:07:30 +00:00
d023a319a4
Nuke some junk in scsi_link, as pointed out by Gordon.
1994-05-12 22:16:04 +00:00
thorpej