- use correct offsets to pass args to loaded kernel in __mips_o32 case
Now NetBSD/pmax kernel properly boots, but init(8) still doesn't start
on GXemul emulating R3000 3MAX.
trees, because it can race with the libsa/libkern/etc. makefiles' own
cleandir rules. I think I've found all of the uses of the offending idiom...
Closes PR 43360.
canonicalise several of the ipf option segments in various files
(this mostly means adding commented out IPFILTER_DEFAULT_BLOCK,
or adding commented or uncommented IPFILTER_LOG or IPFILTER_LOOKUP
option statements.)
i built about 20 of these kernels to check, but not all of them.
on the amount of physical memory and limited by NMBCLUSTERS if present.
Architectures without direct mapping also limit it based on the kmem_map
size, which is used as backing store. On i386 and ARM, the maximum KVA
used for mbuf clusters is limited to 64MB by default.
The old default limits and limits based on GATEWAY have been removed.
key_registered_sb_max is hard-wired to a value derived from 2048
clusters.
- Replace most remaining uses of l_addr with uvm_lwp_getuarea() or lwp_getpcb().
- Amend assembly in ports where it accesses PCB via struct user.
- Rename L_ADDR to L_PCB in few places. Reduce sys/user.h inclusions.
We have to mask higher bits on NCR register access via bus_space_read_4(9),
as the previous NCR_READ_REG() does.
Problem reported by Erik Bertelsen on port-pmax@.
I tested a different version on 3MIN and I also tested committed version
on gxemul, but 3MAX doesn't have asc_ioasic but asc_tc..
[ Kernel symbol table invalid! ] message at boot,
which means no ksyms(4) support even on GENERIC kernel.
Should be pulled up to netbsd-4 and netbsd-5.
There are still about 1600 left, but they have ',' or /* ... */
in the actual variable definitions - which my awk script doesn't handle.
There are also many that need () -> (void).
(The script does handle misordered arguments.)
- renamed to MEMORY_DISK_RBFLAGS to better fit the rest of the
MEMORY_DISK options(4)
- change default value to RB_AUTOBOOT instead of RB_SINGLE, and adapt
the config(5) files accordingly
- document this option inside options(4)
See also http://mail-index.netbsd.org/tech-kern/2008/12/25/msg003924.html
Reviewed by abs@ in private mail.
to avoid unnecessary 64 bit ops which would make binaries larger:
satime_t (currently unsigned int):
numbers in seconds returned by the machine dependent getsecs() function
which are used to measure relative time
saseconds_t (currently int):
numbers in seconds used to specify timeout to network drivers
Per discussion on current-users.
phases, so move the initialization of the ksyms mutex back into main via
a function called ksyms_init. Rename the existing (but quite different)
ksyms_init* variations into ksyms_addsyms_elf() and ksyms_addsyms_explicit()
and adapt machdep code accordingly.
doshutdownhooks(9): shutdown hooks registered by shutdownhook_establish(9)
expect to be called with interrupts disabled, but shutdown hooks
registered with pmf_device_register1(9) expect to be called with
interrupts enabled. So I have made two changes:
1 Do not call pmf_system_shutdown() from doshutdownhooks(). Instead,
change every call to doshutdownhooks() to a call to doshutdownhooks()
followed by a call to pmf_system_shutdown(). No functional change
is intended by this change.
2 Make i386 re-enable interrupts briefly while it calls
pmf_system_shutdown(). I leave it to others either to fix the
other ports, or to factor out some MI shutdown code, as joerg@
suggests, and fix that. Note that a functional change *is* intended
by this change.
I hope that this patch will stop us from flip-flopping between
calling doshutdownhooks() and pmf_system_shutdown() sometimes with
and sometimes without interrupts enabled.
