ISP_DAC_SUPPORTED is defined and do a real typedef for the size
of DMA addresses. ISP_DAC_SUPPORTED also decides how much of any
particular DMA address is significant.
Lose STRNCAT over the side.
Add in (sight unseen) 10160 support.
Start doing the work necessary to support DAC (Dual Address Cycle)
environments. This allows for direct DMA to > 4GB memory from a PCI
card.
Lose STRNCAT over the side and use SNPRINTF instead.
so that PHY instance is not siginificant in ifmedia_match(). This
is done to support multiple PHYs on the MII. Without this change,
ifmedia_set() would panic the system when no PHYs were matched.
I ran into this on an AMD EasyNow PC, which is built around SiS
system chips with an embedded SiS 900 core, and an external AMD
Am79c901 PHY, which presents two PHYs on the MII: one for HomePNA,
and one for standard 10base-T. The 10base-T PHY ends up with instance
number 1...
to char-cell based vga(4) driver, and fully compatible with existing
apps like XFree86. Currently it supports 80x25, 80x30, 80x40 and 80x50
text modes using emulation. You can enable it by specifying `options
VGA_RASTERCONSOLE' in your kernel config file.
Note that displaying multilingual text doesn't work yet. Necessary
code is already there, but userland stuff and some functionality isn't
ready for prime time yet. I'm working on them.
It seems that the firmware accept 104bit key only if
all the keys have 104bit length. We get the length of
the transmit key and use it for all other keys.
Perhaps we should use software WEP for such situation.
- Add "outputs.surround", "outputs.center", and "outputs.lfe"
- If the codec is not capable of a feature, mixer variables
about the feature is not created. For example, no
"outputs.tone" for a codec without tone control.
- Set the following mixer values in ac97_attach():
outputs.master=127,127
outputs.master.mute=off
outputs.headphones.mute=off
outputs.surround=127,127
outputs.surround.mute=off
outputs.center=127
outputs.center.mute=off
outputs.lfe=127
outputs.lfe.mute=off
inputs.dac.mute=off
inputs.cd.mute=off
inputs.line.mute=off
inputs.aux.mute=off
inputs.video.mute=off
record.volume.mute=off
because the default setting of AC'97 codec (all mutes are on,
and maximum volume) is troublesome.
- Make "char*" parameters of ac97_get_portnum_by_name() "const char*"
Codec ID changes:
- If a codec ID is unknown but its vendor ID is known,
ac97_attach() prints the vendor name like "dev0: <vendor name>
unknown (0xXXXXXXXX) codec;"
- Add IDs of Asahi Kasei AK4542, AK4544, AK4544A, AK4545,
Realtek ALC100
- Correct a vendor name: "Advance Logic" -> "Avance Logic"
- Add capability of codec-specific initialization
ac97_attach():
- CDAC, SDAC, and LDAC are eanabled.
- DELAY() before mixer settings. ThinkPad X24 needs it.
ALC650 codec specific change:
- Add "outputs.surround.lineinjack" to switch the line-in jack
to the surround output
- Add "outputs.center.micjack" and "outputs.lfe.micjack" (alias
of "outputs.center.micjack") to switch the mic jack to the
center/lfe output.
rename former uriopoll() to urioselect() and provide it only for OpenBSD -
FreeBSD uses nopoll() for urio too
g/c no longer needed uriopoll define for OpenBSD
uwe