specified by including a Makefile.inc from the appropriate MD directory.
stdlib doesn't do that, but there's no reason that it shouldn't (and
it'd be nice to eliminate the 'if's from the MI stdlib Makefile.inc).
still needs an option to specify the distribution sets from a filesystem
present in fstab.
Add "ados" to the list file recognized filesystems.
Increase label information table size to 16 to allow for 16 partitions.
- clean up debug code
- Don't check ATAPI signature when probing ATA drives, ATAPI devices were
detected before
- Reset controller after disks probes. The probe, with some combinations of
ATA/ATAPI device keep it in a mostly working, but strange state (with busy
led on)
- The WDCF_IRQ_WAIT flag is now cleared by wdc_ata_intr and wdc_atapi_intr
when appropriate (helps recover from failure conditions)
- In wdcunwedge, send ATAPI_SOFT_RESET to non-ata drives
(helps recover from failure conditions)
- in wdctimeout be a bit more verbose when we missed an interrupt
- Always Increment xfer->c_skip where it should be
- Set the ITSDONE flag when a polled command completed.
for 12-bit addresses. This causes PCMCIA cards mapped at 0x400 and higher
to not function properly. However, the range 0x300-0x3ff causes some
laptops (e.g. the NEC Versa 6030X) to hang if cards are mapped there.
So, after some experimentation, we compromise. If the probe discovers
a 12-bit address bus, don't trust it. Instead, use the range 0x330-0x3ff.
This has been shown to work on the laptops that the 0x300-0x3ff range is
known to fail on.
escape character (including line continuation), unless the `-r' option
is specified:
* adopt to this behaviour, add the `-r' option to disable it;
* remove the `-e' option, which was previously necessary to get this behaviour.
+ set MAKE_PROGRAM variable in bsd.port.mk to either ${GMAKE} or
${MAKE}, and use it in do-build and do-install targets
+ if X11 package, and man pages are installed, add install.man to
${INSTALL_TARGET}, rather than using a separate command to do this.
Also added CATn= blah.0, similar to MANn= blah.1, which installs
pre-formatted man pages, like the ones imake produces.
* Change find_disks: after mouting target root, check for
/etc/fstab in target, and abort upgrade if not found.
* Change upgrade to check if the target root has /etc.old
before renaming the target /etc -> /etc.old. If found, abort.
(may indicates a failed upgrade.)
* Add save_etc(). saves target /etc as /etc.old, then copies back
config files we might want during upgrade, in case target is current root.
* Fix logic that fscks and mounts disks. Use subroutines to
fsck with a warning message and ok() on continue. Same for doing mounts.
* Fix bug in extract_dist(). Do NOT do target prefixing on the dist_dir,
since we didn't do target prefixing when mounting it.
(At least, NFS does't.)
* Add function to sanity-check target root.
Call after upgrade/install is done.
* Change MSG_realdir to print the strerror() of any errors.
Change target_chdir() to check if chdir() returns -1 and return errno.
* Make sure /dev exists before cd'ing there and running MAKEDEV.
* Use target_fopen() and fprintf() to write network state to disk,
to avoid inadvertent shell escapes.
* Fix silly typo in append_to_target_file. (maybe add shell quotes?)
with wording modified for clarity.
Last sentence of the patch omitted because I do not understand what
it means, even after some examination of the unix domain kernel code.
supports generic SMC91cxx-based ISA cards and the built-in SMC
Ethernet found in some laptop docking stations.
Thanks much to Andrew Gillham <gillhaa@ghost.whirlpool.com> for
making this work!
per class of syscall stubs. This is much more efficient (though it's still
pretty inefficient).
This also fixes a problem with syscall.h and DESTDIR which was pretty
well buried in the old implementation.
From Chris Demetriou <cgd@pa.dec.com>.
but is a marked improvement. This takes advantage of a pseudo-DMA hardware
hack of Apple's that exposes a 16-bit register that the Apple-designed
memory controller acts like a DMA controller and handshakes into or out
of the FIFO. Wierd.
Unfortunately, there does not seem to be a good way to determine what
variety of comm-slot card is present in a machine. There is still an
interrupt issue preventing these cards from working--hopefully that will
be ironed out shortly.
phil