http://mail-index.netbsd.org/tech-userlevel/2011/08/25/msg005404.html
This is used by disk tools such as disklabel(8) to dynamically decide is
the undelyling platform uses a disklabel-in-mbr-partition or not
(instead of using a compile-time list of ports).
getlabelusesmbr() reads the sysctl kern.labelusesmbr, takes its value from the
machdep #define LABELUSESMBR.
For evbmips, make LABELUSESMBR 1 if the platform uses pmon
as bootloader, and 0 (the previous value) otherwise.
sys/stdarg.h and expect compiler to provide proper builtins, defaulting
to the GCC interface. lint still has a special fallback.
Reduce abuse of _BSD_VA_LIST_ by defining __va_list by default and
derive va_list as required by standards.
- make news3400_badaddr() work even if interrupts are disabled
(in the old world bus error interrupt is enabled even during splhigh())
- make ipl_sr_map values model dependent
Now GENERIC kernel boots to single user properly on R3000 NWS-3470D,
though sh(1) still gets floating point exceptions during /etc/rc scripts.
news5000 is untested (yet).
to store disk quota usage and limits, integrated with ffs
metadata. Usage is checked by fsck_ffs (no more quotacheck)
and is covered by the WAPBL journal. Enabled with kernel
option QUOTA2 (added where QUOTA was enabled in kernel config files),
turned on with tunefs(8) on a per-filesystem
basis. mount_mfs(8) can also turn quotas on.
See http://mail-index.netbsd.org/tech-kern/2011/02/19/msg010025.html
for details.
copyright. Confirmed by Mike Hibler, mike at cs.utah.edu - thanks!
Also, merge UCB and Utah copyright texts back into one, as they
originally were.
Extra verification by snj@.
disabled by -D) from the output of newvers_stand.sh. Change -D to the
inverted logic, so that it adds the date to bootprog_rev in ().
Change all platforms accordingly. -D is added if MKREPRO is not yes and
wasn't present before. Platforms that didn't use -D don't depend on
MKREPRO now either.
Establish interrupt handlers with proper softc per each zs device
rather than sharing them among all zs devices and searching softc
in handlers, to avoid possible recursive lock.
Tested on NWS-3470D. xafb.c for NWS-5000 is untested.
XXX: isn't it better to have failsafe default than sprinkle RI_NO_AUTO
XXX: to avoid fatal silent hangup?
canonicalise several of the ipf option segments in various files
(this mostly means adding commented out IPFILTER_DEFAULT_BLOCK,
or adding commented or uncommented IPFILTER_LOG or IPFILTER_LOOKUP
option statements.)
i built about 20 of these kernels to check, but not all of them.
on the amount of physical memory and limited by NMBCLUSTERS if present.
Architectures without direct mapping also limit it based on the kmem_map
size, which is used as backing store. On i386 and ARM, the maximum KVA
used for mbuf clusters is limited to 64MB by default.
The old default limits and limits based on GATEWAY have been removed.
key_registered_sb_max is hard-wired to a value derived from 2048
clusters.
#if NBPFILTER is no longer required in the client. This change
doesn't yet add support for loading bpf as a module, since drivers
can register before bpf is attached. However, callers of bpf can
now be modularized.
Dynamically loadable bpf could probably be done fairly easily with
coordination from the stub driver and the real driver by registering
attachments in the stub before the real driver is loaded and doing
a handoff. ... and I'm not going to ponder the depths of unload
here.
Tested with i386/MONOLITHIC, modified MONOLITHIC without bpf and rump.
- Replace most remaining uses of l_addr with uvm_lwp_getuarea() or lwp_getpcb().
- Amend assembly in ports where it accesses PCB via struct user.
- Rename L_ADDR to L_PCB in few places. Reduce sys/user.h inclusions.
<sys/systm.h> to the one file that did not already contain it.
This now means that physmem can be changed by updating systm.h and uvm_page.c
(excluding fixing printfs)
- renamed to MEMORY_DISK_RBFLAGS to better fit the rest of the
MEMORY_DISK options(4)
- change default value to RB_AUTOBOOT instead of RB_SINGLE, and adapt
the config(5) files accordingly
- document this option inside options(4)
See also http://mail-index.netbsd.org/tech-kern/2008/12/25/msg003924.html
Reviewed by abs@ in private mail.
to avoid unnecessary 64 bit ops which would make binaries larger:
satime_t (currently unsigned int):
numbers in seconds returned by the machine dependent getsecs() function
which are used to measure relative time
saseconds_t (currently int):
numbers in seconds used to specify timeout to network drivers
Per discussion on current-users.
phases, so move the initialization of the ksyms mutex back into main via
a function called ksyms_init. Rename the existing (but quite different)
ksyms_init* variations into ksyms_addsyms_elf() and ksyms_addsyms_explicit()
and adapt machdep code accordingly.
bouyer