5b00b99bef
Allow DRQ[A-C] to be used on the 1888 as well.
1999-03-19 12:40:21 +00:00
b6ee330d4e
dmapos should start at 0, in theory.
...
Also experimentally force polling mode.
1999-03-18 06:04:21 +00:00
039246b8d5
Add support for polling.
1999-03-18 04:31:36 +00:00
ff4754d6e5
Confirm that there was an interrupt before handling it. Allows IRQs to be
...
shared with other devices.
1999-03-18 02:44:27 +00:00
8ace2247cb
Fix a couple of other places we should avoid the Audio2 DRQ on the 1788.
1999-03-17 02:39:59 +00:00
81a1ade358
More redux:
...
* Use a single routine to halt both input and output on Audio1.
* Reduce the number of register reads/writes used to set up a channel.
* A few other minor things.
1999-03-17 01:06:17 +00:00
84f100d175
Audio1 does not support 16-bit DMA. Eliminate some code that tried to handle
...
that case.
1999-03-16 14:17:00 +00:00
13d43eb62b
Fix old typo.
1999-03-16 13:37:23 +00:00
e085a0c921
A little more cleanup.
1999-03-16 13:32:25 +00:00
28e080a143
Minor fix to some debugging output.
1999-03-16 13:24:27 +00:00
3e404912dc
Clean up the previous:
...
* Separate the interrupt handlers based on which channel (audio1/audio2)
rather than which direction (input/output). Only register the handler for
audio1 on the 1788.
* Since the input sides are actually the same, GC the duplicated code.
* Re-KNF in a bunch of places.
* Make this work again on the 1887 in the Shark.
1999-03-16 13:06:35 +00:00
64fffdfef9
Add support for the 1788 AudioDrive chip.
...
Some minor cleanup; refer to more registers by macros rather
than raw hex constants.
1999-03-02 20:36:50 +00:00
ea50d6f672
Use DMAMODE_LOOPDEMAND.
...
Fixes the audible glitches (due to FIFO underruns) when receiving network
packets on the Shark.
1999-02-22 01:57:33 +00:00
b81ad0de61
Fix the halt_input and halt_output routines to actually disable the channel,
...
not just the DMA FIFO. Fixes problems with sample misalignment.
1999-02-20 23:28:37 +00:00
e5f5e628d2
Pass the direction to the allocm and round_buffersize methods.
...
Some drivers need this to properly allocate DMAable memory.
1999-02-17 02:37:38 +00:00
88ad3aa42b
If we have an 8-bit DRQ, always pass that to isa_malloc().
1999-02-17 01:22:47 +00:00
0d32a9a78b
Fix more `void *' arithmetic.
1999-01-08 19:22:34 +00:00
3357fbeefb
Minor format change.
1998-11-25 13:39:37 +00:00
8d64ea1683
Less debug printing.
1998-08-26 13:08:44 +00:00
bb3c56652c
Make the OPL driver turn on the sound on sound cards that require it.
...
That makes it much more likely that we get any sound. DUH!
1998-08-26 12:10:22 +00:00
c7e036f6e2
Let opl attach to ess.
...
WARNING: it doesn't work yet.
1998-08-22 22:55:09 +00:00
cd09067eb4
* Redo the way the way the MIDI driver attaches to audio devices.
...
* Improve the midisyn layer a little.
* Add a driver for the Yamaha OPL[23] FM synths.
The opl driver is not finished yet; it sounds pretty awful.
For some strange reason I cannot get any FM sound from my SB64 cards,
but a regular SB16 works fine.
1998-08-17 21:16:09 +00:00
5c76b6a944
The mic preamp is really a property of the input stage, and affects both
...
pass-through and recording.
1998-08-12 19:13:14 +00:00
3979b06d00
enhanced -> preamp
1998-08-12 03:18:34 +00:00
1f5c14d8ef
ess_audio_channel:active is now used even when DIAGNOSTICS is not defined.
1998-08-11 12:16:22 +00:00
7fca135b1b
Use the new trigger interface.
1998-08-10 15:32:18 +00:00
b4e0bf5dfb
Use 4- and 8-byte DMA transfers.
1998-08-09 06:52:57 +00:00
0611fc34f8
Don't actually touch the hardware in set_params; defer that until we actually
...
start a transfer. Instead, just check that the parameters are valid.
Also, use 16-bit output for u-law and a-law.
1998-08-09 06:38:30 +00:00
5eba82397c
Oops; fix typo.
1998-08-09 04:59:55 +00:00
017b9af5fe
Clarify with a specific reference to the manual page in question.
1998-08-09 04:58:08 +00:00
12f5a41e1f
Make the previous slightly more robust, and set AUDIO_PROP_INDEPENDENT.
1998-08-09 04:40:55 +00:00
c8532af3b2
Make sure the sample rate is the same on both channels, tracking the change
...
from one channel to the other if only one is active.
1998-08-09 04:14:47 +00:00
759ca5ee0c
The manual says to use the other crystal for 22050Hz.
1998-08-09 03:48:42 +00:00
565adbaffb
Set the FIFO control bits correctly so that stereo recording works.
1998-08-09 02:54:50 +00:00
80457a2c65
Use auto-initialize DMA for recording.
1998-08-09 02:05:52 +00:00
254afcaecb
Sleeping forever kinda sucks.
1998-08-08 21:37:00 +00:00
17932f0575
Set the correct modes for the record channel.
1998-08-08 20:55:36 +00:00
7b044dea51
Make the irq checking logic somewhat less bogus.
1998-08-07 00:51:06 +00:00
f76fb48283
Use looping DMA for play channel.
...
More cleanup.
1998-08-04 13:14:42 +00:00
ce69d417a2
Make it compile without DIAGNOSTIC
1998-07-31 23:54:09 +00:00
6b407a79c6
Major cleanup of the ESS driver. It now sorta works. More to come.
1998-07-31 15:17:17 +00:00
bf52ef5697
Squash unused variable.
1998-07-30 22:17:34 +00:00
cdeb158d5f
A first stab at making the SHARK sound work. It doesn't really work
...
yet, but it probes and makes a noise when used. Stay tuned!
1998-07-30 14:11:42 +00:00
080dc567e8
A first stab at an ESS1887 driver. The code is from the SHARK port
...
and needs a lot of polishing. The code compiles (on i386), but is
untested. See ess.c for a TODO list.
1998-06-29 20:56:21 +00:00
mycroft