that the adapter is disabled even if it wasn't enabled/disabled during
configuring its children. This fixes the bug that if an aic pcmcia card
is inserted in a slot during boot, further attaching of any card on the
slot fails once the card is removed.
done in a special order. Do that here also, but for now inside #ifdef vax
because of the (possible) impact on other arch's.
Now vaxen without IOMMU can use the MI LANCE driver.
LiViD DVD player. (See forthcoming mail to current-users.)
XXX NOTE: We should do something to probe capabilities, rather than allowing
these ioctls on any device.
Symptoms: system would crash with "data modified on free list" pool
panic from the mbuf cluster pool shortly after a resume. The cluster
in question contained a valid 82557 receive descriptor and an IP
packet. Happened sporadically in normal use. Easiest way for me to
reproduce it was to run tcpdump and a flood ping and do a
suspend/resume cycle or two.
Changes:
- in interrupt handler, if the interface isn't in IFF_RUNNING state,
just ack interrupts and return; don't try to receive packets, queue
new descriptors, etc., etc.,
- add power control hook to take interface down on suspend,
and restart it (if it was up) on resume.
- tweaks to fxp_stop and fxp_shutdown to avoid recursive panics due
to the (now fixed) bug.
- Don't use int32_t/u_int32_t unless we must.
- Remove C++ single line comment delimeters that crept in.
- Remove defs pertaining to byte granularity 'ragged-edge' bitmasks.
- Move all declarations of per-depth initialization functions to rasops.h.
- Other minor cleanup.
- Don't trust HA_ST_MORE again if the above situation occurs.
- Nuke bitfields in 'struct eata_sp'.
- Don't bother using scatter-gather if DMA map contains only 1 segment.
- Return TRY_AGAIN_LATER and not COMPLETE if an EATA command times out.
- Check SCSI status in dpt_inquire(), not just HBA status.
- Some cosmetic changes and sanity checks.
to be corrected. Text drawing is now improved significantly, but;
cursor is drawn incorrectly, copycols() trashes a screen, 'standout
(\033[7m)' results in lines reversed entirely until '\033[0m', and
possibly more issues. Not multi-colour, 8bpp only this moment. Costly
write memory barrier instrunctions should be eliminated using framebuffer
address aliasing technique for NetBSD/alpha.
and one which isn't. The latter is now used for ttyEcfg, enabling the
VT-switching ioctls to work on it. (This allows Linux X servers to work when
/emul/linux/dev/tty0 is linked to /dev/ttyEcfg.)
CardBus bus stub, YENTA PCI-CardBus bridge (cbb), 3Com 3C575TX driver
(ex) and Intel fxp driver.
TODO:
o Conform to the KNF more strictly.
o Be unified with pcmcia code as much as possible.
o Add more drivers for CardBus card, such as APA-1480 or USB card.
The affected files are listed below.
sys/arch/i386/conf/files.i386
sys/arch/macppc/conf/files.macppc
sys/conf/files
sys/dev/ic/elinkxl.c
sys/dev/ic/elinkxlvar.h
sys/dev/ic/i82365.c
sys/dev/ic/i82365var.h
sys/dev/isa/i82365_isasubr.c
sys/dev/pci/files.pci
sys/dev/pcmcia/pcmcia.c
sys/dev/pcmcia/pcmciachip.h
The added files are listed below.
sys/arch/i386/conf/CARDBUS
sys/arch/i386/include/rbus_machdep.h
sys/arch/i386/i386/rbus_machdep.c
sys/arch/macppc/include/rbus_machdep.h
sys/arch/macppc/macppc/rbus_machdep.c
sys/dev/cardbus/if_ex_cardbus.c
sys/dev/cardbus/Makefile.cardbusdevs
sys/dev/cardbus/cardbus.c
sys/dev/cardbus/cardbus_map.c
sys/dev/cardbus/cardbusdevs
sys/dev/cardbus/cardbusdevs.h
sys/dev/cardbus/cardbusdevs_data.h
sys/dev/cardbus/cardbusvar.h
sys/dev/cardbus/cardslot.c
sys/dev/cardbus/cardslotvar.h
sys/dev/cardbus/devlist2h.awk
sys/dev/cardbus/files.cardbus
sys/dev/cardbus/if_fxp_cardbus.c
sys/dev/cardbus/pccardcis.h
sys/dev/cardbus/rbus.c
sys/dev/cardbus/rbus.h
sys/dev/pci/pccbb.c
sys/dev/pci/pccbbreg.h
sys/dev/pci/pccbbvar.h
CardBus bus stub, YENTA PCI-CardBus bridge (cbb), 3Com 3C575TX driver
(ex) and Intel fxp driver.
TODO:
o Conform to the KNF more strictly.
o Be unified with pcmcia code as much as possible.
o Add more drivers for CardBus card, such as APA-1480 or USB card.
The affected files are listed below.
sys/arch/i386/conf/files.i386
sys/arch/macppc/conf/files.macppc
sys/conf/files
sys/dev/ic/elinkxl.c
sys/dev/ic/elinkxlvar.h
sys/dev/ic/i82365.c
sys/dev/ic/i82365var.h
sys/dev/isa/i82365_isasubr.c
sys/dev/pci/files.pci
sys/dev/pcmcia/pcmcia.c
sys/dev/pcmcia/pcmciachip.h
The added files are listed below.
sys/arch/i386/conf/CARDBUS
sys/arch/i386/include/rbus_machdep.h
sys/arch/i386/i386/rbus_machdep.c
sys/arch/macppc/include/rbus_machdep.h
sys/arch/macppc/macppc/rbus_machdep.c
sys/dev/cardbus/if_ex_cardbus.c
sys/dev/cardbus/Makefile.cardbusdevs
sys/dev/cardbus/cardbus.c
sys/dev/cardbus/cardbus_map.c
sys/dev/cardbus/cardbusdevs
sys/dev/cardbus/cardbusdevs.h
sys/dev/cardbus/cardbusdevs_data.h
sys/dev/cardbus/cardbusvar.h
sys/dev/cardbus/cardslot.c
sys/dev/cardbus/cardslotvar.h
sys/dev/cardbus/devlist2h.awk
sys/dev/cardbus/files.cardbus
sys/dev/cardbus/if_fxp_cardbus.c
sys/dev/cardbus/pccardcis.h
sys/dev/cardbus/rbus.c
sys/dev/cardbus/rbus.h
sys/dev/pci/pccbb.c
sys/dev/pci/pccbbreg.h
sys/dev/pci/pccbbvar.h
so we'll know when it's time to switch from 'slow' command mode to normal.
Change some settings for configuration printfs and debug levels. Redo the
internal ispscsicmd return definitions and let isp_cmd translate them as
approrpriate to NetBSD values. Remove the inline functions from here- they're
now in isp_inline.h. Put in the start of the correct SWIZZLE/UNSWIZZLE
functions.
Redo how we start commands- do a 'slow' start function which then
looks to see when we're done the configuration process at which point
it *then* enables sync/wide mode. Set the max openings amount to the
true max openings- not a synthetic. Add a timeout driven command requeue
function so that Loop Down events well freeze things until a later point
in time where they might be restarted.
isp_fastpost_complete function to include a handle. Do some
isr register debouncing. Use new inline functions for xflist
handle storage. Remove isp_dumpxflist function. Do some fixups
of NVRAM from some broken cards. Use Full Login after LIP option
for FC cards if f/w < 1.17 - there's a f/w bug that causes the
port database to not be actually refreshed for local loop devices!
Do the appropriate endian swizzling for the ICB. Ditto for SNS structures
(these are no-ops until UltraSparc PCI needs them).
defines to get max luns for a card. Make sure the RESULT_QUEUE_LEN is not less
than 64- I've seen breakage with that. Move the temp port database stuff
into the softc (ick). Remove most of the target mode stuff. Make xflist
storage an external outer layer thing (since it will now be allocated based
upon the maximum commands that this HBA can support rather than request
queue size).
the correct "read eeprom" opcode on the RoadRunner (which has a larger
EEPROM, and thus needs a different opcode to make room for the larger
offsets).
- Reset and enable the MII before probing for PHYs, and reset and enable
the MII in epinit().
- Be more conservative when resetting the interface after a transmit error.
Based on PR #8331, from Ryoji KATO.
Closer on 3c574, probably will work fine with the 3CCFEM556BI (which
won't have an older rev TDK Semi PHY, and which was tested by the author
of the PR).
do a gross hack which allows seemingly-broken quantum drives to function
with this driver. The gross hack is to disable tagged queueing completely
when QUEUE FULL is received. That costs performance on drives which
do tagged queueing properly and which return QUEUE FULL, but given the way
this driver works it's seems to be the only thing short of significant
recoding which will make it function with the quantum drives in question.
2. pull in a fix from FreeBSD:
revision 1.18
date: 1999/09/17 18:04:14; author: wpaul; state: Exp; lines: +3 -3
Remember to account for ETHER_ALIGN when setting the maxmimum packet
length for mini receive ring. The max length was MHLEN, however the mbufs
are actually shortened to MHLEN - ETHER_ALIGN to force payload alignment.
queueing support that decreases the number of openings on a device; it
previously assumed that a scsipi_link's `openings' were descreased as
commands were issued, which is not longer the case (`active' is increased).
1. Add power control to reduce power consumption.
The behavior can be controlled by mixerctl(1).
2. Add suspend/resume hook to keep the parameters.
Currently this includes CODEC and control registers but
does not include the DMA state. FIXME.
3. Support "opl at ym" and "mpu at ym" attachment.
Actually, this is required for power control.
4. Add support for the on-chip 3D enhancement hardware.
This includes bass/treble enhancement, wide stereo, and
the equalization mode. This can be controlled by mixerctl(1).
5. Make "audioctl -w play.gain=xxx" work like as
"mixerctl -w inputs.dac=xxx" and now it changes
the wave output volume correctly.
6. Support hardware master volume switches.
7. Change formula of calculating gain so that all the levels
should be used equally.
8. Change "audioctl name" to "OPL3-SA3" and "audioctl version"
to the version of the chip.
- Mute wave output, not the mixer output, on changing CODEC settings.
- Add support for muting wave output while playback or monitoring is inactive.
- Change formula of calculating gain so that all the levels should be
used equally (the old code uses the min/max gain only at 0/255).
- Cleanup
