allocate a static buffer, which is added at the end of short packets
to pad the buffer to ETHER_MIN_LEN - ETHER_CRC_LEN.
While I'm there fix 2 bugs:
in qeinit(), unload the right dmamap if bus_dmamap_load fails
in qestart, don't dmamap_load the mbuf if its len is 0.
Tested on simh-vax.
* return `switched to same process' only if that process was actually
already on a run queue when we entered.
* skip the switch to the idle stack if we can switch immediately
* .. and because of this, don't release the scheduler lock until after
we've fully switched to the new process's stack.
> Module Name: src
> Committed By: augustss
> Date: Sun Jan 12 23:46:12 UTC 2003
>
> Modified Files:
> src/sys/arch/pmppc/pmppc: bus_space.c
>
>Log Message:
>The bus_space_mmap() returns a physaddr, not a page, on the PPC.
>(This is broken in some (all?) of the PPC ports, it seems.)
XXX scsipi mid layer spews out a few "generic HBA error"s during device probe (no slave device on bus), I don't know how to fix this
XXX This whole thing should die now that we have wdc_amiga
Add cpp definitions for the DMA control register fields needed for
5703/5704 configuration on PCI-X.
Add softc copy of internal"local control" register clobbered by reset.
quirk on all 5700 revision B devices. (These fixes have not been
tested against NetBSD recently; committing the fix and the enable separately
gives us flexibility about which fixes get pulled into the NetBSD-1.6 branch.)
* Add support for 5704C dual-channel chip with integral copper PHY (tested)
and 5704S dual-channel SERDES/TBI gbic (untested). Add PHY DSP patch
for 5704.
* Update PHY DSP-code patch for bcm5401 to match latest Linux driver.
* Add PHY DSP-code patch for 5703 (untested).
* Update onchip buffer tunables to recommended values from Linux drivers.
* Disable MWI access. This chip family cannot hanlde PCI stalls
in the middle of an MWI burst. The driver has heuristics to detect PCI
line size, but under load, some PCI bridges may force stalls which
the attach-time heruistics do not catch. Some PCI bridges never
do this, so maybe it should be a tunable option.
* bcm5700 rev Bx chips have a race condition, where updating the
Tx producer pointer goes un-noticed by the chip. Workaround is to
write the new producer-pointer value twice.
* bcm5700 chips rev Bx wedge up if given DMA descriptors of
eight bytes or less. Once hit, only reovery is a watchdog timeout/reset.
If the offending packet is retransmitted, the chip will wedge again...
Check for teeny fragments in a Tx request, and either fold the
teeny chunk residue into an adjacent mbuf, or m_dup the entire buffer.
(NB: quirk not yet enabled; in-place folding tested only on FreeBSD.)
* Add workaround for revision Bx bcm5700: chip bugs in decoding
of PCI register writes may leave the hardware in (partial) powersave state,
such that writes to "indirect" registers do not work.
Explicitly force chip into D0 state at attach time.
* Accessing PHY registers with the bge chip in autopoll mode, when
link-state is the process of changing, may cause the bge chip to
assert PCI errors. Workaround: when doing miibus register access,
save autopoll state, disable around access, and restore autopoll state.
NB: issuing PHY resets may give a window where the problem still occurs.
* Increase Tx interrupt-coalescing thresholds, to reduce Tx-done interrupts.
after the other CPUs have already return into the PROM through prom_cpustop().
So don't do it; try to halt the other CPUs only when an actual `halt'
is requested.
My guess in this case is that the PROM does not expect its original boot
CPU to call prom_cpustop(0), or possibly treats it as the equivalent of
a prom_halt() which is then called again by some other CPU. In any case,
the result is garbage.
