each vm_page structure. Add a VM_MDPAGE_INIT() macro to init this
data when pages are initialized by UVM. These macros are mandatory,
but ports may #define them to nothing if they are not needed/used.
This deprecates struct pmap_physseg. As a transitional measure,
allow a port to #define PMAP_PHYSSEG so that it can continue to
use it until its pmap is converted to use VM_MDPAGE_MEMBERS.
Use all this stuff to eliminate a lot of extra work in the Alpha
pmap module (it's smaller and faster now). Changes to other pmap
modules will follow.
- pmap_enter()
- pmap_remove()
- pmap_protect()
- pmap_kenter_pa()
- pmap_kremove()
as described in pmap(9).
These calls are relatively conservative. It may be possible to
optimize these a little more.
and use appropriately
- create more helper macros:
. cdev__xyz_init(c,n), such as cdev__ocri_init() for
/* open, close, read, ioctl */, etc.
. cdev__xRy_init(c,n), where nullop is used instead of enodev to dummy out
method `R' and the comments now read /* xxx (read) yyy */ instead
. cdev__xyz_t_init(c,n,t) - as per cdev__xyz_init, but sets d_type = t
as well
- use seltrue instead of dev_noimpl(poll,*), as (IIRC) cdevsw.d_poll should
always DTRT WRT returning a valid result. (a few devices previously
incorrectly returned ENODEV)
- use dev_noimpl(stop,enodev) instead of dev_noimpl(stop,nullop) if tty
== 0, because it doesn't matter if dev_type_stop isn't implemented in that
case, and it allows the use of the cdev__xyz_init macros. certain ports
(sparc,sparc64,x68k) used the nullop method for dev_type_stop in a few
drivers, whereas everything else uses enodev
- ensure that the comments are accurate WRT the behaviour of a given entry
rather than assigning to the whole field, set or clear individual flags,
which implies that the B_BUSY and B_INVAL flags will remain set.
this allows us to make the assertion in brelse() that B_BUSY is set,
which is the purpose of all this.
maps standard boot flags to corresponding RB_* values
use BOOT_FLAG() in port's MD code as appropriate
as discussed on tech-kern, add new boot flags -v, -q for booting
verbosely or quietly, and corresponding AB_VERBOSE/AB_QUIET
boot flags; also add FreeBSD-compatible bootverbose macro and
NetBSD-specific bootquiet macro
for hpcmips, use new bootverbose instead of it's own hpcmips_verbose
Tested on i386, and to limited extend (compile of affected files) also for
mvme68k, hp300, luna68k, sun3.
routine. Works similarly fto pmap_prefer(), but allows callers
to specify a minimum power-of-two alignment of the region.
How we ever got along without this for so long is beyond me.
* put #includes of opt headers and headers to get protos used by
net/netisr_dispatch.h in net/netisr.h (if !defined(_LOCORE)) (rather than
in netisr_dispatch.h itself, and potentially nowhere, respectively).
* require netisr.h to be included before netisr_dispatch.h.
* minor additional cleanup of both netisr.h and netisr_dispatch.h.
* clean up uses to remove now-unnecessary header file inclusions, and
local prototypes of the fns.
* convert netisr dispatch implementations which didn't use
netisr_dispatch.h (pc532) to use it.
- for sizeof(void *) == 8 arch, this is mandatory. MHLEN is too small
already (less than 80) and there are chances for unwanted packet loss due
to m_pullup restriction.
- for other cases, the change should avoid allocating clusters in most cases
(even when you have IPv4 IPsec tunnel, or IPv6 with moderate amount of
extension header)
portmasters: if your arch chokes with the change (high memory usage or
whatever), please backout the change for your arch.
thorpej