-sys/lib/libkern builds as library per default (as it was documented all
the time)
-ports able to LKM set "KERN_AS=obj" explicitely in their Makefiles
(for now; should depend on actual "option LKM" or -better- functions
included for LKM use should be pulled in by a stub)
-always link libcompat before libkern - libkern stuff can be referred to
by libcompat, but not the other way
_1 and for _2 in the contiguous and interleaved case.
- while we're here, reorganize bus.h into sections, and use the defined
convenience functions everywhere.
struct scsipi_adapter; they were not used.
Add a scsipi_ioctl entry point to struct scsipi_adapter. This will be
used to issue ioctl commands to the host adapters.
Inspired by PR #6090, from Matt Jacob.
which require special handling, e.g. sigreturn on m68k.
This differs from the old sigreturn trap in that we require the syscall
number to be in register d0, just like the regular syscall entry point.
This will allow sigreturn to be versioned in the future without the need
to allocate another trap vector.
u-area in machine-dependent code. Instead, call exit2() to schedule
the reaper to free them for us, once it is safe to do so (i.e. we are
no longer running on the dead proc's vmspace and stack).
69040/060 and the number of initial KPT pages is odd. This would cause
a memofy fault before the 040 trap routines were set up and gave a
misleading trap message. The odd number of KTP pages would result if
Sysptsize was patched, or if a large amount of Zorro3 space was needed.
- machine independent chip driver, in dev/ic/smc90cx6.c/...reg.h,...var.h,
using bus_space methods
- ZBUS frontend in arch/amiga/dev/if_bah_zbus.c
- added IPL_SOFTNET to arch/amiga/include/intr.h, for this
Implementing the ISA bus frontend is left as an exercise to the reader.
* Improve the midisyn layer a little.
* Add a driver for the Yamaha OPL[23] FM synths.
The opl driver is not finished yet; it sounds pretty awful.
For some strange reason I cannot get any FM sound from my SB64 cards,
but a regular SB16 works fine.
Replace it by a variable, which is initialized in amiga_init.c.
This will make the kernel actually work even if we have lots of Zorro-III
(or DraCo direct bus) i/o space.
tty structures, and on some machines (namely the DraCo internal lpt, and some
multi-i/o boards for Amigas and DraCos), tying spltty to the pretty high printer
interupt level would hurt serial performance.
On all affected ports but Amiga, spllpt() has been defined in machine/intr.h
to be spltty(), thus preserving old behaviour. Portmasters are encouraged to
change is, if they feel something else is better (e.g., one of its own were
possible).
register anyway when the bit is set, we can safe one of the (slow) custom
chip accesses by using this bit.
Sounds ridiculous, but at a hardware FIFO depth of 1 and ~1 usec per
access (at IPL 5) it might help the highspeed addicts.
now be inserted into the kernel for a self-contained installation kernel.
No more questions or problems trying to copy the miniroot to the swap
partition.
as with user-land programs, include files are installed by each directory
in the tree that has includes to install. (This allows more flexibility
as to what gets installed, makes 'partial installs' easier, and gives us
more options as to which machines' includes get installed at any given
time.) The old SYS_INCLUDES={symlinks,copies} behaviours are _both_
still supported, though at least one bug in the 'symlinks' case is
fixed by this change. Include files can't be build before installation,
so directories that have includes as targets (e.g. dev/pci) have to move
those targets into a different Makefile.
a HAVE_GCC28 check-variable that can now be used to add other gcc-2.8
flags in cases where they may be useful, or to remove gcc 2.7.2 "bug
workaround" flags.)
up on systems that have Zorro I/O space allocated outside the Z2 I/O
region, and then only if kvm usage is high enough to begin allocating
pages already mapped for hardware mappings. Found and fixed by Niklas
Hallqvist on OpenBSD.
From niklas@cvs.openbsd.org:
Yay! This fixes a bug that has been there since day one of the amiga port.
We have never protected the kvm area that maps Zorro I/O registers in the
Z2 memory space from being allocated by the kmem_* routines. Lately kvm
usage has increased and we have needed more kvm allocated than earlier thus
this area have got allocated with random results. Most often resulting in
MMU fault panics, but also in hangs. This bug has stalled the amiga port
release builds for several weeks, but now I *hope* the amiga will have a
chance to be built and tested in time for 2.3.
it from the QuickLogic chip version byte.
If found, switch it to non-autorepeat mode (which seems to avoid the race
condition which made my keyboard driver / X server lose state under heavy
interupt load).
If not found, assume an Amiga keyboard on CIA-A.
XXX We should probe for the presence of the CIAs on the DraCo.
as this breaks C++ code that happens to indirectly include this header.
Both Matthias Scheler and I noticed this, independently.
This problem notably does not affect the atari and sun3/sun3x ports,
which have already implemented a similar solution.
are still in-order, but cached reads dont wait for the last write to finish.
Xamiga on a Altais in 8bit-mode became 30% faster servicing xanim (well, 6%
if you count xanim, too).
- make sure all sigreturn error conditions are reported to the caller,
instead of the place jumped to.
This is the bugfix part of pr 4628 by ITOH Yasufumi.
The performance optimization part will be handled seperately, after evaluating
its implications.
Testing on 68040 and removing the performance change from the proposed patch
by scottr. Half of the Amiga machdep.c change had to be done manually by me,
as the patchfile didn't apply cleanly.
XXX Yes, Amiga should be changed to use the common sig_machdep.c instead.
XXX Really soon now. I promise.
was converted to use Mach VM for Net2/4.4BSD. The user segment table
pointer was originally stored in the PCB. When Mach VM came along,
however, it was also stored in the pmap, and loaded into the PCB in
pmap_activate(). pmap_activate() would then note that the PCB's USTP
was now in sync with the pmap's USTP, and the low-level context switch
code would use the value from the PCB.
However, pmap_activate() would also load the hardware MMU context if
the pmap was the current pmap (or, in the case where pmaps can be shared,
such as in NetBSD, if the proc was the current proc). The low-level
context switch code would then reload the hardware _again_ using the
USTP from the PCB.
However, the optimization of not calling pmap_activate() if "stchanged"
was false ended up causing some processes to use stale USTP values from
the PCB when the low-level context switch code reloaded the hardware!
This was noticed by using a real vfork(2) (which worked for some time
before failing, surprisingly!)
Since I'm hard pressed to find any real optimization here (since the
hardware was always reloaded once, sometimes twice!), the code now always
calls pmap_activate(), which uses the correct USTP value (the one in the
pmap). The PCB's USTP is now ignored, and should eventually be g/c'd.
Another optimization can actually be performed, and I have added a comment
describing what it is, but have not yet implemented it.
Also note that most of the loadustp() functions where actually incomplete.
This has been corrected. These functions should probably be split up into
MMU-specific operations, and called indirectly, rather than doing constant
run-time decision making based on values that will never change during the
course of a boot's lifetime.
We play mono samples on all 4 channels.
However, we get the volume settings for mono samples as a symmetic two-channel
setting... the other two channels used to stay at max volume...
I believe that something else is wrong here, but dont want to change MI
code (which in turn influences a couple of MD driver) thus late in the release
cycle.
- use board address space > 4 MB, instead of iszthreepa(), to detect Z3-mode
boards. We dont want the bus, but want the address configuration.
- s/CV64CONSOLE/CV3DCONSOLE/
- s/cv3d_zorroIII == 1/cv3d_zorroIII/ and s/cv3d_zorroIII != 1/!cv3d_zorroIII/
the CyberVision64 driver. Modified by Tobias Abt with some bugfixes
from Bernd Ernesti.
ZorroII is at the moment not supported and there is a small problem
with the Console driver where you just get a black screen, but the
system boots and you can use X11 without a problem.
The changes is to allow some limited mixer manipulation through
the audio device (instead of the mixer device).
This rendered 4 methods in audio_hw_if unused so garbage collect these.
pseudo-device rnd # /dev/random and in-kernel generator
in config files.
o Add declaration to all architectures.
o Clean up copyright message in rnd.c, rnd.h, and rndpool.c to include
that this code is derived in part from Ted Tyso's linux code.
is