NetBSD/sys/dev/usb/ustirreg.h

174 lines
5.5 KiB
C
Raw Normal View History

/* $NetBSD: ustirreg.h,v 1.1 2002/01/03 18:54:32 augustss Exp $ */
/*
* Copyright (c) 2001 The NetBSD Foundation, Inc.
* All rights reserved.
*
* This code is derived from software contributed to The NetBSD Foundation
* by David Sainty <David.Sainty@dtsp.co.nz>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software
* must display the following acknowledgement:
* This product includes software developed by the NetBSD
* Foundation, Inc. and its contributors.
* 4. Neither the name of The NetBSD Foundation nor the names of its
* contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
* TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*/
/*
* Registers definitions for SigmaTel STIr4200 USB/IrDA Bridge
* Controller. Documentation available at:
* http://extranet.sigmatel.com/library/infrared/stir4200/stir4200-ds.pdf
*/
/* Notes:
*
* The data sheet states that the TX and RX frames are prepended with
* BOF characters. This appears to be incorrect, the standard 0xff
* characters behave as expected.
*
* There does not appear to be any way to get asynchronous
* notifications from this device that data is waiting. You simply do
* have to poll continuously looking for a non-zero-length result.
*
* The SigmaTel drivers provided with the device for other operating
* systems poll at full USB speed (1000 per second), which has a
* significant impact on the system.
*/
/*
* The SigmaTel device is controlled via an array of registers, with
* generic register read/write commands. This is a completely
* different approach to that defined in the USB IrDA standard.
*/
#define STIR_REG_MODE 1
#define STIR_REG_BRATE 2
#define STIR_REG_CONTROL 3
#define STIR_REG_SENSITIVITY 4
#define STIR_REG_STATUS 5
#define STIR_REG_FFCNT_LSB 6
#define STIR_REG_FFCNT_MSB 7
#define STIR_REG_DPLL 8
#define STIR_REG_IRDIG 9
/* Register numbers range from zero to STIR_MAX_REG */
#define STIR_MAX_REG 15
/* Mode register bits */
#define STIR_RMODE_FIR 0x80
#define STIR_RMODE_MIR 0x40
#define STIR_RMODE_SIR 0x20
#define STIR_RMODE_ASK 0x10
/*
* FASTRXEN can be set to enable simultaneous reads and writes. It
* isn't clear that this is useful, the RX and TX data is mixed into
* the FIFO and the chip appears to get into a funny state. In the
* absence of good documentation about this bit, leave it disabled!
*/
#define STIR_RMODE_FASTRXEN 0x08
#define STIR_RMODE_FFRSTEN 0x04
/* FFSPRST must be set to enable the FIFO */
#define STIR_RMODE_FFSPRST 0x02
/*
* High bit baud rate generator value, used in conjunction with the
* BRATE register.
*/
#define STIR_RMODE_PDCLK8 0x01
/* Status register bits */
#define STIR_RSTATUS_EOFRAME 0x80
#define STIR_RSTATUS_FFUNDER 0x40
#define STIR_RSTATUS_FFOVER 0x20
/* Set in write direction, cleared in read direction */
#define STIR_RSTATUS_FFDIR 0x10
/*
* FFCLR is write-only, and the only writable bit in the STATUS
* register.
*/
#define STIR_RSTATUS_FFCLR 0x08
#define STIR_RSTATUS_FFEMPTY 0x04
#define STIR_RSTATUS_FFRXERR 0x02
#define STIR_RSTATUS_FFTXERR 0x01
/* Extract data from portions of registers */
#define STIR_GET_SENSITIVITY_CHIPREVISION(x) ((x) & 7)
/*
* According to the documentation, FFCNT may be off by as much as 3
* bytes.
*/
#define STIR_FFCNT_MARGIN 3
/*
* The FIFO size for the device is a fixed 4k bytes
*/
#define STIR_FIFO_SIZE 0x1000
/*
* Vendor specific device requests
*/
#define STIR_CMD_WRITEMULTIREG 0x00
#define STIR_CMD_READMULTIREG 0x01
#define STIR_CMD_READROM 0x02
#define STIR_CMD_WRITESINGLEREG 0x03
/*
* The MSB is the MODE register setting, the LSB is the BRATE register
* setting.
*/
#define STIR_BRMODE_4000000 0x8002
#define STIR_BRMODE_1152000 0x4001
#define STIR_BRMODE_576000 0x4003
#define STIR_BRMODE_115200 0x2009
#define STIR_BRMODE_57600 0x2013
#define STIR_BRMODE_38400 0x201d
#define STIR_BRMODE_19200 0x203b
#define STIR_BRMODE_9600 0x2077
#define STIR_BRMODE_2400 0x21df
/*
* Extract values from STIR_BRMODE values.
*/
#define STIR_BRMODE_MODEREG(x) ((x) >> 8)
#define STIR_BRMODE_BRATEREG(x) ((x) & 0xff)
/*
* Each transmit frame starts with the sequence:
*
* 0x55 0xaa LSB(Length) MSB(Length)
*/
#define STIR_OUTPUT_HEADER_SIZE 4
#define STIR_OUTPUT_HEADER_BYTE0 0x55
#define STIR_OUTPUT_HEADER_BYTE1 0xaa