3a61c8db9d
Firmware can enumerate present at boot APs by broadcasting wakeup IPI, so that woken up secondary CPUs could register them-selves. However in CPU hotplug case, it would need to know architecture specific CPU IDs for possible and hotplugged CPUs so it could prepare environment for and wake hotplugged AP. Reuse and extend existing CPU hotplug interface to return architecture specific ID for currently selected CPU in 2 registers: - lower 32 bits in ACPI_CPU_CMD_DATA_OFFSET_RW - upper 32 bits in ACPI_CPU_CMD_DATA2_OFFSET_R On x86, firmware will use CPHP_GET_CPU_ID_CMD for fetching the APIC ID when handling hotplug SMI. Later, CPHP_GET_CPU_ID_CMD will be used on ARM to retrieve MPIDR, which serves the similar to APIC ID purpose. Signed-off-by: Igor Mammedov <imammedo@redhat.com> Message-Id: <1575896942-331151-10-git-send-email-imammedo@redhat.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Laszlo Ersek <lersek@redhat.com>
150 lines
6.9 KiB
Plaintext
150 lines
6.9 KiB
Plaintext
QEMU<->ACPI BIOS CPU hotplug interface
|
|
--------------------------------------
|
|
|
|
QEMU supports CPU hotplug via ACPI. This document
|
|
describes the interface between QEMU and the ACPI BIOS.
|
|
|
|
ACPI BIOS GPE.2 handler is dedicated for notifying OS about CPU hot-add
|
|
and hot-remove events.
|
|
|
|
============================================
|
|
Legacy ACPI CPU hotplug interface registers:
|
|
--------------------------------------------
|
|
CPU present bitmap for:
|
|
ICH9-LPC (IO port 0x0cd8-0xcf7, 1-byte access)
|
|
PIIX-PM (IO port 0xaf00-0xaf1f, 1-byte access)
|
|
One bit per CPU. Bit position reflects corresponding CPU APIC ID. Read-only.
|
|
The first DWORD in bitmap is used in write mode to switch from legacy
|
|
to modern CPU hotplug interface, write 0 into it to do switch.
|
|
---------------------------------------------------------------
|
|
QEMU sets corresponding CPU bit on hot-add event and issues SCI
|
|
with GPE.2 event set. CPU present map is read by ACPI BIOS GPE.2 handler
|
|
to notify OS about CPU hot-add events. CPU hot-remove isn't supported.
|
|
|
|
=====================================
|
|
Modern ACPI CPU hotplug interface registers:
|
|
-------------------------------------
|
|
Register block base address:
|
|
ICH9-LPC IO port 0x0cd8
|
|
PIIX-PM IO port 0xaf00
|
|
Register block size:
|
|
ACPI_CPU_HOTPLUG_REG_LEN = 12
|
|
|
|
All accesses to registers described below, imply little-endian byte order.
|
|
|
|
Reserved resisters behavior:
|
|
- write accesses are ignored
|
|
- read accesses return all bits set to 0.
|
|
|
|
The last stored value in 'CPU selector' must refer to a possible CPU, otherwise
|
|
- reads from any register return 0
|
|
- writes to any other register are ignored until valid value is stored into it
|
|
On QEMU start, 'CPU selector' is initialized to a valid value, on reset it
|
|
keeps the current value.
|
|
|
|
read access:
|
|
offset:
|
|
[0x0-0x3] Command data 2: (DWORD access)
|
|
if value last stored in 'Command field':
|
|
0: reads as 0x0
|
|
3: upper 32 bits of architecture specific CPU ID value
|
|
other values: reserved
|
|
[0x4] CPU device status fields: (1 byte access)
|
|
bits:
|
|
0: Device is enabled and may be used by guest
|
|
1: Device insert event, used to distinguish device for which
|
|
no device check event to OSPM was issued.
|
|
It's valid only when bit 0 is set.
|
|
2: Device remove event, used to distinguish device for which
|
|
no device eject request to OSPM was issued.
|
|
3-7: reserved and should be ignored by OSPM
|
|
[0x5-0x7] reserved
|
|
[0x8] Command data: (DWORD access)
|
|
contains 0 unless value last stored in 'Command field' is one of:
|
|
0: contains 'CPU selector' value of a CPU with pending event[s]
|
|
3: lower 32 bits of architecture specific CPU ID value
|
|
(in x86 case: APIC ID)
|
|
|
|
write access:
|
|
offset:
|
|
[0x0-0x3] CPU selector: (DWORD access)
|
|
selects active CPU device. All following accesses to other
|
|
registers will read/store data from/to selected CPU.
|
|
Valid values: [0 .. max_cpus)
|
|
[0x4] CPU device control fields: (1 byte access)
|
|
bits:
|
|
0: reserved, OSPM must clear it before writing to register.
|
|
1: if set to 1 clears device insert event, set by OSPM
|
|
after it has emitted device check event for the
|
|
selected CPU device
|
|
2: if set to 1 clears device remove event, set by OSPM
|
|
after it has emitted device eject request for the
|
|
selected CPU device
|
|
3: if set to 1 initiates device eject, set by OSPM when it
|
|
triggers CPU device removal and calls _EJ0 method
|
|
4-7: reserved, OSPM must clear them before writing to register
|
|
[0x5] Command field: (1 byte access)
|
|
value:
|
|
0: selects a CPU device with inserting/removing events and
|
|
following reads from 'Command data' register return
|
|
selected CPU ('CPU selector' value).
|
|
If no CPU with events found, the current 'CPU selector' doesn't
|
|
change and corresponding insert/remove event flags are not modified.
|
|
1: following writes to 'Command data' register set OST event
|
|
register in QEMU
|
|
2: following writes to 'Command data' register set OST status
|
|
register in QEMU
|
|
other values: reserved
|
|
[0x6-0x7] reserved
|
|
[0x8] Command data: (DWORD access)
|
|
if last stored 'Command field' value:
|
|
1: stores value into OST event register
|
|
2: stores value into OST status register, triggers
|
|
ACPI_DEVICE_OST QMP event from QEMU to external applications
|
|
with current values of OST event and status registers.
|
|
other values: reserved
|
|
|
|
Typical usecases:
|
|
- (x86) Detecting and enabling modern CPU hotplug interface.
|
|
QEMU starts with legacy CPU hotplug interface enabled. Detecting and
|
|
switching to modern interface is based on the 2 legacy CPU hotplug features:
|
|
1. Writes into CPU bitmap are ignored.
|
|
2. CPU bitmap always has bit#0 set, corresponding to boot CPU.
|
|
|
|
Use following steps to detect and enable modern CPU hotplug interface:
|
|
1. Store 0x0 to the 'CPU selector' register,
|
|
attempting to switch to modern mode
|
|
2. Store 0x0 to the 'CPU selector' register,
|
|
to ensure valid selector value
|
|
3. Store 0x0 to the 'Command field' register,
|
|
4. Read the 'Command data 2' register.
|
|
If read value is 0x0, the modern interface is enabled.
|
|
Otherwise legacy or no CPU hotplug interface available
|
|
|
|
- Get a cpu with pending event
|
|
1. Store 0x0 to the 'CPU selector' register.
|
|
2. Store 0x0 to the 'Command field' register.
|
|
3. Read the 'CPU device status fields' register.
|
|
4. If both bit#1 and bit#2 are clear in the value read, there is no CPU
|
|
with a pending event and selected CPU remains unchanged.
|
|
5. Otherwise, read the 'Command data' register. The value read is the
|
|
selector of the CPU with the pending event (which is already
|
|
selected).
|
|
|
|
- Enumerate CPUs present/non present CPUs
|
|
01. Set the present CPU count to 0.
|
|
02. Set the iterator to 0.
|
|
03. Store 0x0 to the 'CPU selector' register, to ensure that it's in
|
|
a valid state and that access to other registers won't be ignored.
|
|
04. Store 0x0 to the 'Command field' register to make 'Command data'
|
|
register return 'CPU selector' value of selected CPU
|
|
05. Read the 'CPU device status fields' register.
|
|
06. If bit#0 is set, increment the present CPU count.
|
|
07. Increment the iterator.
|
|
08. Store the iterator to the 'CPU selector' register.
|
|
09. Read the 'Command data' register.
|
|
10. If the value read is not zero, goto 05.
|
|
11. Otherwise store 0x0 to the 'CPU selector' register, to put it
|
|
into a valid state and exit.
|
|
The iterator at this point equals "max_cpus".
|