When register Rcvr_timeout_reg0 (R_RTOR in cadence_uart.c) is set to
0, the receiver timeout counter should be disabled. See page 1801 of
"Zynq-7000 AP SoC Technical Reference Manual". This commit adds a
such a check before setting the receive timeout interrupt.
Signed-off-by: Andrew Gacek <andrew.gacek@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Cadence UART device emulator calculates speed by dividing the
baud rate by a 'baud rate generator' & 'baud rate divider' value.
The device specification defines these register values to be
non-zero and within certain limits. Checks were recently added when
writing to these registers but not when restoring from migration.
This patch adds checks when restoring from migration to avoid divide by
zero errors.
Reported-by: Huawei PSIRT <psirt@huawei.com>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 04ae30ed8ee1758cd2d2af880da4d28f74c67738.1481132150.git.alistair.francis@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Cadence UART device emulator calculates speed by dividing the
baud rate by a 'baud rate generator' & 'baud rate divider' value.
The device specification defines these register values to be
non-zero and within certain limits. Add checks for these limits
to avoid errors like divide by zero.
Reported-by: Huawei PSIRT <psirt@huawei.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1477596278-1470-1-git-send-email-ppandit@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Cadence UART device emulator stores 'baud rate generator'
and 'baud rate divider' values, used in computing speed, in two
registers. The device specification defines their range and
their reset value. Use their correct value when resetting the
device in cadence_uart_reset.
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1477378140-2670-1-git-send-email-ppandit@redhat.com
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
No need to keep explicit_fe_open around if it affects only a
qemu_chr_fe_set_handlers(). Use an additional argument instead.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-24-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In most cases, front ends do not care about the side effect of
CharBackend, so we can simply skip the checks and call the qemu_chr_fe
functions even without associated CharDriver.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-20-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This also switches from qemu_chr_add_handlers() to
qemu_chr_fe_set_handlers(). Note that qemu_chr_fe_set_handlers() now
takes the focus when fe_open (qemu_chr_add_handlers() did take the
focus)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-16-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
qemu_chr_accept_input() and qemu_chr_disconnect() are only used by
frontend, so use qemu_chr_fe prefix.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-14-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Store the property in a CharBackend instead of CharDriverState*. This
also replace systematically chr by chr.chr to access the
CharDriverState*. The following patches will replace it with calls to
qemu_chr_fe CharBackend functions.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-12-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
g_source_attach can return any value between 1 and UINT_MAX if you let
QEMU run long enough. However, qemu_chr_fe_add_watch can also return
a negative errno value when the device is disconnected or does not
support chr_add_watch. Change it to return zero to avoid overloading
these values.
Fix the cadence_uart which asserts in this case (easily obtained with
"-serial pty").
Tested-by: Bret Ketchum <bcketchum@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If qemu_chr_fe_write() returns an error (represented by a negative
number) we should skip incrementing the count and initiating a
memmove().
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 667e5dc534d33338fcfc2471e5aa32fe7cbd13dc.1466546703.git.alistair.francis@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* drop qemu_char_get_next_serial and use chardev prop
* create cadence_uart_create wrapper function to create
cadence_uart_device
* change affected board code to use the new way
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465028065-5855-3-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
cadence_uart_init() initializes an I/O memory region of size 0x1000
bytes. However in uart_write(), the 'offset' parameter (offset within
region) is divided by 4 and then used to index the array 'r' of size
CADENCE_UART_R_MAX which is much smaller: (0x48/4). If 'offset>>=2'
exceeds CADENCE_UART_R_MAX, this will cause an out-of-bounds memory
write where the offset and the value are controlled by guest.
This will corrupt QEMU memory, in most situations this causes the vm to
crash.
Fix by checking the offset against the array size.
Cc: qemu-stable@nongnu.org
Reported-by: 李强 <liqiang6-s@360.cn>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20160418100735.GA517@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch replaces get_ticks_per_sec() calls with the macro
NANOSECONDS_PER_SECOND. Also, as there are no callers, get_ticks_per_sec()
is then removed. This replacement improves the readability and
understandability of code.
For example,
timer_mod(fdctrl->result_timer,
qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) + (get_ticks_per_sec() / 50));
NANOSECONDS_PER_SECOND makes it obvious that qemu_clock_get_ns
matches the unit of the expression on the right side of the plus.
Signed-off-by: Rutuja Shah <rutu.shah.26@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-13-git-send-email-peter.maydell@linaro.org
Create a new header for Cadence UART to allow using the device with
modern SoC programming conventions. The state struct needs to be
visible to embed the device in SoC containers.
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 46a0fbd45b6b205f54c4a8c778deb75c77f8abdf.1431381507.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Clean up some variable names in preparation for migrating the state struct
and type cast macro to a public header. The acronym "UART" on it's own is
not specific enough to be used in a more global namespace so preface with
"cadence". Fix the capitalisation of "uart" in the state type while touching
the typename. Preface macros used by the state struct itself with CADENCE_UART
so they don't conflict in namespace either.
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 3812b7426c338beae9e082557f3524a99310ddc6.1431381507.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Device models aren't supposed to go on fishing expeditions for
backends. They should expose suitable properties for the user to set.
For onboard devices, board code sets them.
A number of sysbus devices pick up block backends in their init() /
instance_init() methods with drive_get_next() instead: sl-nand,
milkymist-memcard, pl181, generic-sdhci.
Likewise, a number of sysbus devices pick up character backends in
their init() / realize() methods with qemu_char_get_next_serial():
cadence_uart, digic-uart, etraxfs,serial, lm32-juart, lm32-uart,
milkymist-uart, pl011, stm32f2xx-usart, xlnx.xps-uartlite.
All these mistakes are already marked FIXME. See the commit that
added these FIXMEs for a more detailed explanation of what's wrong.
Fortunately, only machines ppce500 and pseries-* support -device with
sysbus devices, and none of the devices above is supported with these
machines.
Set cannot_instantiate_with_device_add_yet to preserve our luck.
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Character devices defined with -serial and -parallel are for board
initialization to wire up. Board code examines serial_hds[] and
parallel_hds[] to find them, and creates devices with their qdev
chardev properties set accordingly.
Except a few devices go on a fishing expedition for a suitable backend
instead of exposing a chardev property for board code to set: they use
serial_hds[] (often via qemu_char_get_next_serial()) or parallel_hds[]
in their realize() or init() method to connect to a backend.
Picking up backends that way works when the devices are created by
board code. But it's inappropriate for -device or device_add. Not
only is it inconsistent with how the other characrer device models
work (they connect to a backend explicitly identified by a "chardev"
property), it breaks when the backend has been picked up by the board
or a previous -device / device_add already.
Example:
$ qemu-system-ppc64 -M bamboo -S -device i82378 -device pc87312 -device pc87312
qemu-system-ppc64: -device pc87312: Property 'isa-parallel.chardev' can't take value 'parallel0', it's in use
Mark them with suitable FIXME comments.
Cc: Li Guang <lig.fnst@cn.fujitsu.com>
Cc: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Cc: "Andreas Färber" <andreas.faerber@web.de>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Use DeviceClass::realize() and TypeInfo::instance_init() instead of
the deprecated SysBusDevice::init().
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
This checks that s->chr is not NULL before using it.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On FreeBSD polling a master pty while the other end is not connected
with G_IO_OUT only results in an endless wait. This is different from
the Linux behaviour, that returns immediately. In order to demonstrate
this, I have the following example code:
http://xenbits.xen.org/people/royger/test_poll.c
When executed on Linux:
$ ./test_poll
In callback
On FreeBSD instead, the callback never gets called:
$ ./test_poll
So, in order to workaround this, poll the source with G_IO_HUP (which
makes the code behave the same way on both Linux and FreeBSD).
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Cc: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Cc: Michael Tokarev <mjt@tls.msk.ru>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: xen-devel@lists.xenproject.org
[Add hw/char/cadence_uart.c too. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After commit 767adce2d, they are redundant. This way we don't assign them
except when needed. Once there, there were lots of cases where the ".fields"
indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (apart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
[PMM: fixed minor conflict, corrected commit message typos]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the UART back-end blocks, buffer in the Tx FIFO to try again later.
This stops the IO-thread busy waiting on char back-ends (which causes
all sorts of performance problems).
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 4bea048b3ab38425701d82ccc1ab92545c26b79c.1388626249.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The can_receive logic was only taking into account the RxFIFO
occupancy. RxFIFO population is only used for the echo and normal modes
however. Improve the logic to correctly return the true number of
receivable characters based on the current mode:
Normal mode: RxFIFO vacancy.
Remote loopback: TxFIFO vacancy.
Echo mode: The min of the TxFIFO and RxFIFO vacancies.
Local Loopback: Return non-zero (to implement droppage)
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 36a58440c9ca5080151e95765c2c81342de8a8df.1388626249.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This tx timer implementation is flawed. Despite the controller
attempting to time the guest visable assertion of the TX-empty status
bit (and corresponding interrupt) the controller is still transmitting
characters instantaneously. There is also no sense of multiple character
delay.
The only side effect of this timer is assertion of tx-empty status. So
just remove the timer completely and hold tx-empty as permanently
asserted (its reset status). This matches the actual behaviour of
instantaneous transmission.
While we are VMSD version bumping, add the tx_fifo as device state to
prepare for upcomming TxFIFO flow control. Implement the interrupt
generation logic for the TxFIFO occupancy.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 7a208a7eb8d79d6429fe28b1396c3104371807b2.1388626249.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some (interrupt) status register bits relating to the TxFIFO path were
not defined. Define them. This prepares support for proper Tx data path
flow control.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 2068b963f0af8cc834c353944e9fa816d950b163.1388626249.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The status register bits are always pure functions of other device
state. Move the generation of these bits to the update_status()
function to simplify. Makes developing much easier as theres now no need
to recheck status bits on all the changes to rx/tx fifo state.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 321994929f789096975104f99c55732774be4cae.1388626249.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This should be rechecked on bus write accesses as such accesses may
change the underlying state that generates the interrupt. Particular
relevant for when the guest touches the interrupt status or mask.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 1c250cd61b7b8de492fbc8b79b8370958a56d83b.1388626249.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Most code already used QEMUTimer without the redundant 'struct' keyword.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This is an autogenerated patch using scripts/switch-timer-api.
Switch the entire code base to using the new timer API.
Note this patch may introduce some line length issues.
Signed-off-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
commit 1db8b5efe0 introduced an issue
where QEMU would segfault if you have an unattached Cadence UART.
Fix by guarding the flush-on-reset logic on there being a qemu_chr
attachment.
Reported-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Tested-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Message-id: 9009578ee10a50d994b2e10aa2840d73765f5968.1370577272.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
