The L2 and refcount caches have default sizes that can be overridden
using the l2-cache-size and refcount-cache-size (an additional
parameter named cache-size sets the combined size of both caches).
Unless forced by one of the aforementioned parameters, QEMU will set
the unspecified sizes so that the L2 cache is 4 times larger than the
refcount cache.
This is based on the premise that the refcount metadata needs to be
only a fourth of the L2 metadata to cover the same amount of disk
space. This is incorrect for two reasons:
a) The amount of disk covered by an L2 table depends solely on the
cluster size, but in the case of a refcount block it depends on
the cluster size *and* the width of each refcount entry.
The 4/1 ratio is only valid with 16-bit entries (the default).
b) When we talk about disk space and L2 tables we are talking about
guest space (L2 tables map guest clusters to host clusters),
whereas refcount blocks are used for host clusters (including
L1/L2 tables and the refcount blocks themselves). On a fully
populated (and uncompressed) qcow2 file, image size > virtual size
so there are more refcount entries than L2 entries.
Problem (a) could be fixed by adjusting the algorithm to take into
account the refcount entry width. Problem (b) could be fixed by
increasing a bit the refcount cache size to account for the clusters
used for qcow2 metadata.
However this patch takes a completely different approach and instead
of keeping a ratio between both cache sizes it assigns as much as
possible to the L2 cache and the remainder to the refcount cache.
The reason is that L2 tables are used for every single I/O request
from the guest and the effect of increasing the cache is significant
and clearly measurable. Refcount blocks are however only used for
cluster allocation and internal snapshots and in practice are accessed
sequentially in most cases, so the effect of increasing the cache is
negligible (even when doing random writes from the guest).
So, make the refcount cache as small as possible unless the user
explicitly asks for a larger one.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 9695182c2eb11b77cb319689a1ebaa4e7c9d6591.1523968389.git.berto@igalia.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Now that we can safely call QOBJECT() on QObject * as well as its
subtypes, we can have macros qobject_ref() / qobject_unref() that work
everywhere instead of having to use QINCREF() / QDECREF() for QObject
and qobject_incref() / qobject_decref() for its subtypes.
The replacement is mechanical, except I broke a long line, and added a
cast in monitor_qmp_cleanup_req_queue_locked(). Unlike
qobject_decref(), qobject_unref() doesn't accept void *.
Note that the new macros evaluate their argument exactly once, thus no
need to shout them.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20180419150145.24795-4-marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Rebased, semantic conflict resolved, commit message improved]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Checking reopen by existence of some bitmaps is wrong, as it may be
some other bitmaps, or on the other hand, user may remove bitmaps. This
criteria is bad. To simplify things and make behavior more predictable
let's just add a flag to remember, that we've already tried to load
bitmaps on open and do not want do it again.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20180411122606.367301-2-vsementsov@virtuozzo.com
[mreitz: Changed comment wording according to Eric Blake's suggestion]
Signed-off-by: Max Reitz <mreitz@redhat.com>
On reopen with existing bitmaps, instead of loading bitmaps, lets
reopen them if needed. This also fixes bitmaps migration through
shared storage.
Consider the case. Persistent bitmaps are stored on bdrv_inactivate.
Then, on destination process_incoming_migration_bh() calls
bdrv_invalidate_cache_all() which leads to
qcow2_load_autoloading_dirty_bitmaps() which fails if bitmaps are
already loaded on destination start.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20180320170521.32152-3-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
This patch was generated using the following Coccinelle script:
@@
expression Obj;
@@
(
- qobject_to_qnum(Obj)
+ qobject_to(QNum, Obj)
|
- qobject_to_qstring(Obj)
+ qobject_to(QString, Obj)
|
- qobject_to_qdict(Obj)
+ qobject_to(QDict, Obj)
|
- qobject_to_qlist(Obj)
+ qobject_to(QList, Obj)
|
- qobject_to_qbool(Obj)
+ qobject_to(QBool, Obj)
)
and a bit of manual fix-up for overly long lines and three places in
tests/check-qjson.c that Coccinelle did not find.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-Id: <20180224154033.29559-4-mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[eblake: swap order from qobject_to(o, X), rebase to master, also a fix
to latent false-positive compiler complaint about hw/i386/acpi-build.c]
Signed-off-by: Eric Blake <eblake@redhat.com>
This adds a synchronous x-blockdev-create QMP command that can create
qcow2 images on a given node name.
We don't want to block while creating an image, so this is not the final
interface in all aspects, but BlockdevCreateOptionsQcow2 and
.bdrv_co_create() are what they actually might look like in the end. In
any case, this should be good enough to test whether we interpret
BlockdevCreateOptions as we should.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Instead of manually creating the BlockdevCreateOptions object, use a
visitor to parse the given options into the QAPI object.
This involves translation from the old command line syntax to the syntax
mandated by the QAPI schema. Option names are still checked against
qcow2_create_opts, so only the old option names are allowed on the
command line, even if they are translated in qcow2_create().
In contrast, new option values are optionally recognised besides the old
values: 'compat' accepts 'v2'/'v3' as an alias for '0.10'/'1.1', and
'encrypt.format' accepts 'qcow' as an alias for 'aes' now.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Once qcow2_co_create() can be called directly on an already existing
node, we must provide the 'full' and 'falloc' preallocation modes
outside of creating the image on the protocol layer. Fortunately, we
have preallocated truncate now which can provide this functionality.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Instead of passing the encryption format name and the QemuOpts down, use
the QCryptoBlockCreateOptions contained in BlockdevCreateOptions.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Instead of passing a separate BlockDriverState* into qcow2_co_create(),
make use of the BlockdevRef that is included in BlockdevCreateOptions.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
All of the simple options are now passed to qcow2_co_create() in a
BlockdevCreateOptions object. Still missing: node-name and the
encryption options.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Currently, qcow2_create() only parses the QemuOpts and then calls
qcow2_co_create() for the actual image creation, which includes both the
creation of the actual file on the file system and writing a valid empty
qcow2 image into that file.
The plan is that qcow2_co_create() becomes the function that implements
the functionality for a future 'blockdev-create' QMP command, which only
creates the qcow2 layer on an already opened file node.
This is a first step towards that goal: Let's move out anything that
deals with the protocol layer from qcow2_co_create() into
qcow2_create(). This means that qcow2_co_create() doesn't need a file
name any more.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
The functions originally known as qcow2_create() and qcow2_create2()
are now called qcow2_co_create_opts() and qcow2_co_create(), which
matches the names of the BlockDriver callbacks that they will implement
at the end of this patch series.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
This function checks that the offset and size of a table are valid.
While the offset checks are fine, the size check is too generic, since
it only verifies that the total size in bytes fits in a 64-bit
integer. In practice all tables used in qcow2 have much smaller size
limits, so the size needs to be checked again for each table using its
actual limit.
This patch generalizes this function by allowing the caller to specify
the maximum size for that table. In addition to that it allows passing
an Error variable.
The function is also renamed and made public since we're going to use
it in other parts of the code.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1516279431-30424-8-git-send-email-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
QED's bdrv_invalidate_cache implementation would like to reuse functions
that acquire/release the metadata locks. Call it from coroutine context
to simplify the logic.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1516279431-30424-6-git-send-email-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It is called from qcow2_invalidate_cache in coroutine context (incoming
migration runs in a coroutine), so it's cleaner if metadata is always
loaded from a coroutine.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1516279431-30424-4-git-send-email-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
They will be used to avoid recursively taking s->lock during
bdrv_open or bdrv_check.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1516279431-30424-7-git-send-email-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
-----BEGIN PGP SIGNATURE-----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=2axz
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches
# gpg: Signature made Mon 05 Mar 2018 17:45:51 GMT
# gpg: using RSA key 7F09B272C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>"
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream: (38 commits)
block: Fix NULL dereference on empty drive error
qcow2: Replace align_offset() with ROUND_UP()
block/ssh: Add basic .bdrv_truncate()
block/ssh: Make ssh_grow_file() blocking
block/ssh: Pull ssh_grow_file() from ssh_create()
qemu-img: Make resize error message more general
qcow2: make qcow2_co_create2() a coroutine_fn
block: rename .bdrv_create() to .bdrv_co_create_opts()
Revert "IDE: Do not flush empty CDROM drives"
block: test blk_aio_flush() with blk->root == NULL
block: add BlockBackend->in_flight counter
block: extract AIO_WAIT_WHILE() from BlockDriverState
aio: rename aio_context_in_iothread() to in_aio_context_home_thread()
docs: document how to use the l2-cache-entry-size parameter
specs/qcow2: Fix documentation of the compressed cluster descriptor
iotest 033: add misaligned write-zeroes test via truncate
block: fix write with zero flag set and iovector provided
block: Drop unused .bdrv_co_get_block_status()
vvfat: Switch to .bdrv_co_block_status()
vpc: Switch to .bdrv_co_block_status()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# include/block/block.h
In my "build everything" tree, a change to the types in
qapi-schema.json triggers a recompile of about 4800 out of 5100
objects.
The previous commit split up qmp-commands.h, qmp-event.h, qmp-visit.h,
qapi-types.h. Each of these headers still includes all its shards.
Reduce compile time by including just the shards we actually need.
To illustrate the benefits: adding a type to qapi/migration.json now
recompiles some 2300 instead of 4800 objects. The next commit will
improve it further.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180211093607.27351-24-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
[eblake: rebase to master]
Signed-off-by: Eric Blake <eblake@redhat.com>
The align_offset() function is equivalent to the ROUND_UP() macro so
there's no need to use the former. The ROUND_UP() name is also a bit
more explicit.
This patch uses ROUND_UP() instead of the slower QEMU_ALIGN_UP()
because align_offset() already requires that the second parameter is a
power of two.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180215131008.5153-1-berto@igalia.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
qcow2_create2() calls qemu_co_mutex_lock(). Only a coroutine_fn may
call another coroutine_fn. In fact, qcow2_create2 is always called from
coroutine context.
Rename the function to add the "co" moniker and add coroutine_fn.
Reported-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20170705102231.20711-3-stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
BlockDriver->bdrv_create() has been called from coroutine context since
commit 5b7e1542cf ("block: make
bdrv_create adopt coroutine").
Make this explicit by renaming to .bdrv_co_create_opts() and add the
coroutine_fn annotation. This makes it obvious to block driver authors
that they may yield, use CoMutex, or other coroutine_fn APIs.
bdrv_co_create is reserved for the QAPI-based version that Kevin is
working on.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20170705102231.20711-2-stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We are gradually moving away from sector-based interfaces, towards
byte-based. Update the qcow2 driver accordingly.
For now, we are ignoring the 'want_zero' hint. However, it should
be relatively straightforward to honor the hint as a way to return
larger *pnum values when we have consecutive clusters with the same
data/zero status but which differ only in having non-consecutive
mappings.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now that the code is ready to handle L2 slices we can finally add an
option to allow configuring their size.
An L2 slice is the portion of an L2 table that is read by the qcow2
cache. Until now the cache was always reading full L2 tables, and
since the L2 table size is equal to the cluster size this was not very
efficient with large clusters. Here's a more detailed explanation of
why it makes sense to have smaller cache entries in order to load L2
data:
https://lists.gnu.org/archive/html/qemu-block/2017-09/msg00635.html
This patch introduces a new command-line option to the qcow2 driver
named l2-cache-entry-size (cf. l2-cache-size). The cache entry size
has the same restrictions as the cluster size: it must be a power of
two and it has the same range of allowed values, with the additional
requirement that it must not be larger than the cluster size.
The L2 cache entry size (L2 slice size) remains equal to the cluster
size for now by default, so this feature must be explicitly enabled.
Although my tests show that 4KB slices consistently improve
performance and give the best results, let's wait and make more tests
with different cluster sizes before deciding on an optimal default.
Now that the cache entry size is not necessarily equal to the cluster
size we need to reflect that in the MIN_L2_CACHE_SIZE documentation.
That minimum value is a requirement of the COW algorithm: we need to
read two L2 slices (and not two L2 tables) in order to do COW, see
l2_allocate() for the actual code.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: c73e5611ff4a9ec5d20de68a6c289553a13d2354.1517840877.git.berto@igalia.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
The qcow2_truncate() code is mostly independent from whether
we're using L2 slices or full L2 tables, but in full and
falloc preallocation modes new L2 tables are allocated using
qcow2_alloc_cluster_link_l2(). Therefore the code needs to be
modified to ensure that all nb_clusters that are processed in each
call can be allocated with just one L2 slice.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Message-id: 1fd7d272b5e7b66254a090b74cf2bed1cc334c0e.1517840877.git.berto@igalia.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
The BDRVQcow2State structure contains an l2_size field, which stores
the number of 64-bit entries in an L2 table.
For efficiency reasons we want to be able to load slices instead of
full L2 tables, so we need to know how many entries an L2 slice can
hold.
An L2 slice is the portion of an L2 table that is loaded by the qcow2
cache. At the moment that cache can only load complete tables,
therefore an L2 slice has the same size as an L2 table (one cluster)
and l2_size == l2_slice_size.
Later we'll allow smaller slices, but until then we have to use this
new l2_slice_size field to make the rest of the code ready for that.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: adb048595f9fb5dfb110c802a8b3c3be3b937f37.1517840877.git.berto@igalia.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
This function was only using the BlockDriverState parameter to pass it
to qcow2_cache_table_release(). This is no longer necessary so this
parameter can be removed.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: b74f17591af52f201de0ea3a3b2dd0a81932334d.1517840876.git.berto@igalia.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
This function was never using the BlockDriverState parameter so it can
be safely removed.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 49c74fe8b3aead9056e61a85b145ce787d06262b.1517840876.git.berto@igalia.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
To maintain load/store disabled bitmap there is new approach:
- deprecate @autoload flag of block-dirty-bitmap-add, make it ignored
- store enabled bitmaps as "auto" to qcow2
- store disabled bitmaps without "auto" flag to qcow2
- on qcow2 open load "auto" bitmaps as enabled and others
as disabled (except in_use bitmaps)
Also, adjust iotests 165 and 176 appropriately.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20180202160752.143796-1-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
We don't need the can_write_zeroes_with_unmap field in
BlockDriverInfo, because it is redundant information with
supported_zero_flags & BDRV_REQ_MAY_UNMAP. Note that
BlockDriverInfo and supported_zero_flags are both per-device
settings, rather than global state about the driver as a
whole, which means one or both of these bits of information
can already be conditional. Let's audit how they were set:
crypto: always setting can_write_ to false is pointless (the
struct starts life zero-initialized), no use of supported_
nbd: just recently fixed to set can_write_ if supported_
includes MAY_UNMAP (thus this commit effectively reverts
bca80059e and solves the problem mentioned there in a more
global way)
file-posix, iscsi, qcow2: can_write_ is conditional, while
supported_ was unconditional; but passing MAY_UNMAP would
fail with ENOTSUP if the condition wasn't met
qed: can_write_ is unconditional, but pwrite_zeroes lacks
support for MAY_UNMAP and supported_ is not set. Perhaps
support can be added later (since it would be similar to
qcow2), but for now claiming false is no real loss
all other drivers: can_write_ is not set, and supported_ is
either unset or a passthrough
Simplify the code by moving the conditional into
supported_zero_flags for all drivers, then dropping the
now-unused BDI field. For callers that relied on
bdrv_can_write_zeroes_with_unmap(), we return the same
per-device settings for drivers that had conditions (no
observable change in behavior there); and can now return
true (instead of false) for drivers that support passthrough
(for example, the commit driver) which gives those drivers
the same fix as nbd just got in bca80059e. For callers that
relied on supported_zero_flags, we now have a few more places
that can avoid a wasted call to pwrite_zeroes() that will
just fail with ENOTSUP.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20180126193439.20219-1-eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-15-armbru@redhat.com>
qapi/qmp/types.h is a convenience header to include a number of
qapi/qmp/ headers. Since we rarely need all of the headers
qapi/qmp/types.h includes, we bypass it most of the time. Most of the
places that use it don't need all the headers, either.
Include the necessary headers directly, and drop qapi/qmp/types.h.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-9-armbru@redhat.com>
This cleanup makes the number of objects depending on qapi/error.h
drop from 1910 (out of 4743) to 1612 in my "build everything" tree.
While there, separate #include from file comment with a blank line,
and drop a useless comment on why qemu/osdep.h is included first.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-5-armbru@redhat.com>
[Semantic conflict with commit 34e304e975 resolved, OSX breakage fixed]
Persistent dirty bitmaps require a properly functioning
autoclear_features field, or we cannot track when an unsupporting
program might overwrite them. Therefore, we cannot support them for
compat=0.10 images.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20171123020832.8165-3-mreitz@redhat.com
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Since bdrv_co_preadv does all neccessary checks including
reading after the end of the backing file, avoid duplication
of verification before bdrv_co_preadv call.
Signed-off-by: Edgar Kaziakhmedov <edgar.kaziakhmedov@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When trying to repair a dirty image, qcow2_check() may apparently
succeed (no really fatal error occurred that would prevent the check
from continuing), but if check_errors in the result object is non-zero,
we cannot trust the image to be usable.
Reported-by: R. Nageswara Sastry <nasastry@in.ibm.com>
Buglink: https://bugs.launchpad.net/qemu/+bug/1728639
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20171110203111.7666-2-mreitz@redhat.com
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Misaligned compressed write is not supported.
Signed-off-by: Anton Nefedov <anton.nefedov@virtuozzo.com>
Message-id: 1510654613-47868-2-git-send-email-anton.nefedov@virtuozzo.com
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
If an image contains persistent bitmaps, we cannot use the
fast path of bdrv_make_empty() to clear the image during
qemu-img commit, because that will lose the clusters related
to the bitmaps.
Also leave a comment in qcow2_read_extensions to remind future
feature additions to think about fast-path removal, since we
just barely fixed the same bug for LUKS encryption.
It's a pain that qemu-img has not yet been taught to manipulate,
or even at a very minimum display, information about persistent
bitmaps; instead, we have to use QMP commands. It's also a
pain that only qeury-block and x-debug-block-dirty-bitmap-sha256
will allow bitmap introspection; but the former requires the
node to be hooked to a block device, and the latter is experimental.
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
After committing the qcow2 image contents into the base image, qemu-img
will call bdrv_make_empty to drop the payload in the layered image.
When this is done for qcow2 images, it blows away the LUKS encryption
header, making the resulting image unusable. There are two codepaths
for emptying a qcow2 image, and the second (slower) codepath leaves
the LUKS header intact, so force use of that codepath.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Currently if trying to change encryption parameters on a qcow2 image, qemu-img
will abort. We already explicitly check for attempt to change encrypt.format
but missed other parameters like encrypt.key-secret. Rather than list each
parameter, just blacklist changing of all parameters with a 'encrypt.' prefix.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The crypto header is initialized only when QEMU is creating a new
image, so there's no chance of this happening on a corrupted image.
If QEMU is really trying to allocate the header overlapping other
existing metadata sections then this is a serious bug in QEMU itself
so let's add an assertion.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Message-id: ae3d77f312fc0c5e0ac2bbd71676c0112eebe2e5.1509718618.git.berto@igalia.com
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
qcow2_do_open() is checking that header.refcount_table_clusters is not
too large, but it doesn't check that it's greater than zero. Apart
from the fact that an image like that is obviously corrupted, trying
to use it crashes QEMU since we end up with a null s->refcount_table
after qcow2_refcount_init().
These images can however be repaired, so allow opening them if the
BDRV_O_CHECK flag is set.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: f9750f50c80359babba11062e88f5075a47e8e16.1509718618.git.berto@igalia.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Some qcow2 functions (at least perform_cow()) expect s->lock to be
taken. Therefore, if we want to make use of them, we should execute
preallocate() (as "preallocate_co") in a coroutine so that we can use
the qemu_co_mutex_* functions.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20171009215533.12530-3-mreitz@redhat.com
Cc: qemu-stable@nongnu.org
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
A qcow2 image file's length is not required to have a length that is a
multiple of the cluster size. However, qcow2_refcount_area() expects an
aligned value for its @start_offset parameter, so we need to round
@old_file_size up to the next cluster boundary.
Reported-by: Ping Li <pingl@redhat.com>
Bug: https://bugzilla.redhat.com/show_bug.cgi?id=1414049
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20171009215533.12530-2-mreitz@redhat.com
Cc: qemu-stable@nongnu.org
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
bdrv_truncate() has an errp parameter which is always set when an error
occurs. Let's use that instead of a plain strerror().
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20171009155431.14093-1-mreitz@redhat.com
Reviewed-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
BDRV_SECTOR_BITS is defined to be 9 in block.h (and BDRV_SECTOR_SIZE
is calculated from that), but there are still a couple of places where
we are using the literal value instead of the macro.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Message-id: 20171009153856.20387-1-berto@igalia.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Now that bdrv_is_allocated accepts non-aligned inputs, we can
remove the TODO added in earlier refactoring.
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We are gradually moving away from sector-based interfaces, towards
byte-based. In the common case, allocation is unlikely to ever use
values that are not naturally sector-aligned, but it is possible
that byte-based values will let us be more precise about allocation
at the end of an unaligned file that can do byte-based access.
Changing the name of the function from bdrv_get_block_status_above()
to bdrv_block_status_above() ensures that the compiler enforces that
all callers are updated. Likewise, since it a byte interface allows
an offset mapping that might not be sector aligned, split the mapping
out of the return value and into a pass-by-reference parameter. For
now, the io.c layer still assert()s that all uses are sector-aligned,
but that can be relaxed when a later patch implements byte-based
block status in the drivers.
For the most part this patch is just the addition of scaling at the
callers followed by inverse scaling at bdrv_block_status(), plus
updates for the new split return interface. But some code,
particularly bdrv_block_status(), gets a lot simpler because it no
longer has to mess with sectors. Likewise, mirror code no longer
computes s->granularity >> BDRV_SECTOR_BITS, and can therefore drop
an assertion about alignment because the loop no longer depends on
alignment (never mind that we don't really have a driver that
reports sub-sector alignments, so it's not really possible to test
the effect of sub-sector mirroring). Fix a neighboring assertion to
use is_power_of_2 while there.
For ease of review, bdrv_get_block_status() was tackled separately.
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
