This value used to reflect the maximum supported memslots from KVM kernel.
Rename it to be clearer.
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Link: https://lore.kernel.org/r/20240917163835.194664-5-peterx@redhat.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will make all nr_slots counters to be named in the same manner.
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Link: https://lore.kernel.org/r/20240917163835.194664-4-peterx@redhat.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Zhiyi reported an infinite loop issue in VFIO use case. The cause of that
was a separate discussion, however during that I found a regression of
dirty sync slowness when profiling.
Each KVMMemoryListerner maintains an array of kvm memslots. Currently it's
statically allocated to be the max supported by the kernel. However after
Linux commit 4fc096a99e ("KVM: Raise the maximum number of user memslots"),
the max supported memslots reported now grows to some number large enough
so that it may not be wise to always statically allocate with the max
reported.
What's worse, QEMU kvm code still walks all the allocated memslots entries
to do any form of lookups. It can drastically slow down all memslot
operations because each of such loop can run over 32K times on the new
kernels.
Fix this issue by making the memslots to be allocated dynamically.
Here the initial size was set to 16 because it should cover the basic VM
usages, so that the hope is the majority VM use case may not even need to
grow at all (e.g. if one starts a VM with ./qemu-system-x86_64 by default
it'll consume 9 memslots), however not too large to waste memory.
There can also be even better way to address this, but so far this is the
simplest and should be already better even than before we grow the max
supported memslots. For example, in the case of above issue when VFIO was
attached on a 32GB system, there are only ~10 memslots used. So it could
be good enough as of now.
In the above VFIO context, measurement shows that the precopy dirty sync
shrinked from ~86ms to ~3ms after this patch applied. It should also apply
to any KVM enabled VM even without VFIO.
NOTE: we don't have a FIXES tag for this patch because there's no real
commit that regressed this in QEMU. Such behavior existed for a long time,
but only start to be a problem when the kernel reports very large
nr_slots_max value. However that's pretty common now (the kernel change
was merged in 2021) so we attached cc:stable because we'll want this change
to be backported to stable branches.
Cc: qemu-stable <qemu-stable@nongnu.org>
Reported-by: Zhiyi Guo <zhguo@redhat.com>
Tested-by: Zhiyi Guo <zhguo@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Link: https://lore.kernel.org/r/20240917163835.194664-2-peterx@redhat.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Ensure the function names match.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-id: 20241012-dma-v2-1-6afddf5f3c8d@daynix.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ``-portrait`` and ``-rotate`` options were documented as only
working with the PXA LCD device, and all the machine types using
that display device were removed in 9.2.
These options were intended to simulate a mobile device being
rotated by the user, and had three effects:
* the display output was rotated by 90, 180 or 270 degrees
(implemented in the PXA display device models)
* the mouse/trackpad input was rotated the opposite way
(implemented in generic code)
* the machine model would signal to the guest about its
orientation
(implemented by e.g. the spitz machine model)
Of these three things, the input-rotation was coded without being
restricted to boards which supported the full set of device-rotation
handling, so in theory the options were usable on other machine
models with odd effects (rotating input but not display output). But
this was never intended or documented behaviour, so we can reasonably
drop these command line arguments without a formal deprecate-and-drop
cycle for them.
Remove the options, and their implementation and documentation.
Describe the removal in removed-features.rst.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20241003140010.1653808-7-peter.maydell@linaro.org
* kvm: support for nested FRED
* tests/unit: fix warning when compiling test-nested-aio-poll with LTO
* kvm: refactoring of VM creation
* target/i386: expose IBPB-BRTYPE and SBPB CPUID bits to the guest
* hw/char: clean up serial
* remove virtfs-proxy-helper
* target/i386/kvm: Report which action failed in kvm_arch_put/get_registers
* qom: improvements to object_resolve_path*()
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmb++MsUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroPVnwf/cdvfxvDm22tEdlh8vHlV17HtVdcC
Hw334M/3PDvbTmGzPBg26lzo4nFS6SLrZ8ETCeqvuJrtKzqVk9bI8ssZW5KA4ijM
nkxguRPHO8E6U33ZSucc+Hn56+bAx4I2X80dLKXJ87OsbMffIeJ6aHGSEI1+fKVh
pK7q53+Y3lQWuRBGhDIyKNuzqU4g+irpQwXOhux63bV3ADadmsqzExP6Gmtl8OKM
DylPu1oK7EPZumlSiJa7Gy1xBqL4Rc4wGPNYx2RVRjp+i7W2/Y1uehm3wSBw+SXC
a6b7SvLoYfWYS14/qCF4cBL3sJH/0f/4g8ZAhDDxi2i5kBr0/5oioDyE/A==
=/zo4
-----END PGP SIGNATURE-----
Merge tag 'for-upstream' of https://gitlab.com/bonzini/qemu into staging
* pc: Add a description for the i8042 property
* kvm: support for nested FRED
* tests/unit: fix warning when compiling test-nested-aio-poll with LTO
* kvm: refactoring of VM creation
* target/i386: expose IBPB-BRTYPE and SBPB CPUID bits to the guest
* hw/char: clean up serial
* remove virtfs-proxy-helper
* target/i386/kvm: Report which action failed in kvm_arch_put/get_registers
* qom: improvements to object_resolve_path*()
# -----BEGIN PGP SIGNATURE-----
#
# iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmb++MsUHHBib256aW5p
# QHJlZGhhdC5jb20ACgkQv/vSX3jHroPVnwf/cdvfxvDm22tEdlh8vHlV17HtVdcC
# Hw334M/3PDvbTmGzPBg26lzo4nFS6SLrZ8ETCeqvuJrtKzqVk9bI8ssZW5KA4ijM
# nkxguRPHO8E6U33ZSucc+Hn56+bAx4I2X80dLKXJ87OsbMffIeJ6aHGSEI1+fKVh
# pK7q53+Y3lQWuRBGhDIyKNuzqU4g+irpQwXOhux63bV3ADadmsqzExP6Gmtl8OKM
# DylPu1oK7EPZumlSiJa7Gy1xBqL4Rc4wGPNYx2RVRjp+i7W2/Y1uehm3wSBw+SXC
# a6b7SvLoYfWYS14/qCF4cBL3sJH/0f/4g8ZAhDDxi2i5kBr0/5oioDyE/A==
# =/zo4
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 03 Oct 2024 21:04:27 BST
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* tag 'for-upstream' of https://gitlab.com/bonzini/qemu: (23 commits)
qom: update object_resolve_path*() documentation
qom: set *ambiguous on all paths
qom: rename object_resolve_path_type() "ambiguousp"
target/i386/kvm: Report which action failed in kvm_arch_put/get_registers
kvm: Allow kvm_arch_get/put_registers to accept Error**
accel/kvm: refactor dirty ring setup
minikconf: print error entirely on stderr
9p: remove 'proxy' filesystem backend driver
hw/char: Extract serial-mm
hw/char/serial.h: Extract serial-isa.h
hw: Remove unused inclusion of hw/char/serial.h
target/i386: Expose IBPB-BRTYPE and SBPB CPUID bits to the guest
kvm: refactor core virtual machine creation into its own function
kvm/i386: replace identity_base variable with a constant
kvm/i386: refactor kvm_arch_init and split it into smaller functions
kvm: replace fprintf with error_report()/printf() in kvm_init()
kvm/i386: fix return values of is_host_cpu_intel()
kvm/i386: make kvm_filter_msr() and related definitions private to kvm module
hw/i386/pc: Add a description for the i8042 property
tests/unit: remove block layer code from test-nested-aio-poll
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# hw/arm/Kconfig
# hw/arm/pxa2xx.c
This is necessary to provide discernible error messages to the caller.
Signed-off-by: Julia Suvorova <jusual@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Link: https://lore.kernel.org/r/20240927104743.218468-2-jusual@redhat.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
blk_by_public last use was removed in 2017 by
c61791fc23 ("block: add aio_context field in ThrottleGroupMember")
blk_activate last use was removed earlier this year by
eef0bae3a7 ("migration: Remove block migration")
blk_add_insert_bs_notifier, blk_op_block_all, blk_op_unblock_all
last uses were removed in 2016 by
ef8875b549 ("virtio-scsi: Remove op blocker for dataplane")
blk_iostatus_disable last use was removed in 2016 by
66a0fae438 ("blockjob: Don't touch BDS iostatus")
Remove them.
Signed-off-by: Dr. David Alan Gilbert <dave@treblig.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
replay_disable_events has been unused since 2019's
c8aa7895eb ("replay: don't drain/flush bdrv queue while RR is working")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <dave@treblig.org>
Reviewed-by: Pavel Dovgalyuk <pavel.dovgalyuk@ispras.ru>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Currently, both qemu_devices_reset() and MachineClass::reset() use
ShutdownCause for the reason of the reset. However, the Resettable
interface uses ResetState, so ShutdownCause needs to be translated to
ResetType somewhere. Translating it qemu_devices_reset() makes adding
new reset types harder, as they cannot always be matched to a single
ShutdownCause here, and devices may need to check the ResetType to
determine what to reset and if to reset at all.
This patch moves this translation up in the call stack to
qemu_system_reset() and updates all MachineClass children to use the
ResetType instead.
Message-ID: <20240904103722.946194-2-jmarcin@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Juraj Marcin <jmarcin@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
We are about to remove the CRIS target, so remove
the sysemu part. This remove the CRIS 'none' machine.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Message-ID: <20240904143603.52934-13-philmd@linaro.org>
This is preliminary work to split up hv_vm_create
logic per platform so we can support creating VMs
with > 64GB of RAM on Apple Silicon machines. This
is done via ARM HVF's hv_vm_config_create() (and
other APIs that modify this config that will be
coming in future patches). This should have no
behavioral difference at all as hv_vm_config_create()
just assigns the same default values as if you just
passed NULL to the function.
Signed-off-by: Danny Canter <danny_canter@apple.com>
Message-id: 20240828111552.93482-3-danny_canter@apple.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Change the data type of the ioctl _request_ argument from 'int' to
'unsigned long' for the various accel/kvm functions which are
essentially wrappers around the ioctl() syscall.
The correct type for ioctl()'s 'request' argument is confused:
* POSIX defines the request argument as 'int'
* glibc uses 'unsigned long' in the prototype in sys/ioctl.h
* the glibc info documentation uses 'int'
* the Linux manpage uses 'unsigned long'
* the Linux implementation of the syscall uses 'unsigned int'
If we wrap ioctl() with another function which uses 'int' as the
type for the request argument, then requests with the 0x8000_0000
bit set will be sign-extended when the 'int' is cast to
'unsigned long' for the call to ioctl().
On x86_64 one such example is the KVM_IRQ_LINE_STATUS request.
Bit requests with the _IOC_READ direction bit set, will have the high
bit set.
Fortunately the Linux Kernel truncates the upper 32bit of the request
on 64bit machines (because it uses 'unsigned int', and see also Linus
Torvalds' comments in
https://sourceware.org/bugzilla/show_bug.cgi?id=14362 )
so this doesn't cause active problems for us. However it is more
consistent to follow the glibc ioctl() prototype when we define
functions that are essentially wrappers around ioctl().
This resolves a Coverity issue where it points out that in
kvm_get_xsave() we assign a value (KVM_GET_XSAVE or KVM_GET_XSAVE2)
to an 'int' variable which can't hold it without overflow.
Resolves: Coverity CID 1547759
Signed-off-by: Johannes Stoelp <johannes.stoelp@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20240815122747.3053871-1-peter.maydell@linaro.org
[PMM: Rebased patch, adjusted commit message, included note about
Coverity fix, updated the type of the local var in kvm_get_xsave,
updated the comment in the KVMState struct definition]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QAPI's 'prefix' feature can make the connection between enumeration
type and its constants less than obvious. It's best used with
restraint.
QCryptodevBackendAlgType has a 'prefix' that overrides the generated
enumeration constants' prefix to QCRYPTODEV_BACKEND_ALG.
We could simply drop 'prefix', but I think the abbreviation "alg" is
less than clear.
Additionally rename the type to QCryptodevBackendAlgoType. The prefix
becomes QCRYPTODEV_BACKEND_ALGO_TYPE.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-ID: <20240904111836.3273842-19-armbru@redhat.com>
This reverts commit 1f881ea4a4.
That commit causes reverse_debugging.py test failures, and does
not seem to solve the root cause of the problem x86-64 still
hangs in record/replay tests.
The problem with short-cutting the iowait that was taken during
record phase is that related events will not get consumed at the
same points (e.g., reading the clock).
A hang with zero icount always seems to be a symptom of an earlier
problem that has caused the recording to become out of synch with
the execution and consumption of events by replay.
Acked-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20240813050638.446172-6-npiggin@gmail.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240813202329.1237572-14-alex.bennee@linaro.org>
When replaying a trace, it is possible to go from shutdown to running
with a reverse-debugging step. This can be useful if the problem being
debugged triggers a reset or shutdown.
This can be tested by making a recording of a machine that shuts down,
then using -action shutdown=pause when replaying it. Continuing to the
end of the trace then reverse-stepping in gdb crashes due to invalid
runstate transition.
Just permitting the transition seems to be all that's necessary for
reverse-debugging to work well in such a state.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20240813050638.446172-5-npiggin@gmail.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240813202329.1237572-13-alex.bennee@linaro.org>
There are distinct helpers for creating and parking a KVM vCPU.
However, there can be cases where a platform needs to create and
immediately park the vCPU during early stages of vcpu init which
can later be reused when vcpu thread gets initialized. This would
help detect failures with kvm_create_vcpu at an early stage.
Suggested-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
* IOMMUFD Dirty Tracking support
* Fix for a possible SEGV in IOMMU type1 container
* Dropped initialization of host IOMMU device with mdev devices
-----BEGIN PGP SIGNATURE-----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=cViP
-----END PGP SIGNATURE-----
Merge tag 'pull-vfio-20240723-1' of https://github.com/legoater/qemu into staging
vfio queue:
* IOMMUFD Dirty Tracking support
* Fix for a possible SEGV in IOMMU type1 container
* Dropped initialization of host IOMMU device with mdev devices
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmafyVUACgkQUaNDx8/7
# 7KGebRAAzEYxvstDxSPNF+1xx937TKbRpiKYtspTfEgu4Ht50MwO2ZqnVWzTBSwa
# qcjhDf2avMBpBvkp4O9fR7nXR0HRN2KvYrBSThZ3Qpqu4KjxCAGcHI5uYmgfizYh
# BBLrw3eWME5Ry220TinQF5KFl50vGq7Z/mku5N5Tgj2qfTfCXYK1Kc19SyAga49n
# LSokTIjZAGJa4vxrE7THawaEUjFRjfCJey64JUs/TPJaGr4R1snJcWgETww6juUE
# 9OSw/xl0AoQhaN/ZTRC1qCsBLUI2MVPsC+x+vqVK62HlTjCx+uDRVQ8KzfDzjCeH
# gaLkMjxJSuJZMpm4UU7DBzDGEGcEBCGeNyFt37BSqqPPpX55CcFhj++d8vqTiwpF
# YzmTNd/znxcZTw6OJN9sQZohh+NeS86CVZ3x31HD3dXifhRf17jbh7NoIyi+0ZCb
# N+mytOH5BXsD+ddwbk+yMaxXV43Fgz7ThG5tB1tjhhNtLZHDA5ezFvGZ5F/FJrqE
# xAbjOhz5MC+RcOVNSzQJCULNqFpfE6Gqeys6btEDm/ltf4LpAe6W1HYuv8BJc19T
# UsqGK2yKAuQX8GErYxJ1zqZCttVrgpsmXFYTC5iGbxC84mvsF0Iti96IdXz9gfzN
# Vlb2OxoefcOwVqIhbkvTZW0ZwYGGDDPAYhLMfr5lSuRqj123OOo=
# =cViP
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 24 Jul 2024 01:16:37 AM AEST
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-vfio-20240723-1' of https://github.com/legoater/qemu:
vfio/common: Allow disabling device dirty page tracking
vfio/migration: Don't block migration device dirty tracking is unsupported
vfio/iommufd: Implement VFIOIOMMUClass::query_dirty_bitmap support
vfio/iommufd: Implement VFIOIOMMUClass::set_dirty_tracking support
vfio/iommufd: Probe and request hwpt dirty tracking capability
vfio/{iommufd, container}: Invoke HostIOMMUDevice::realize() during attach_device()
vfio/iommufd: Add hw_caps field to HostIOMMUDeviceCaps
vfio/{iommufd,container}: Remove caps::aw_bits
vfio/iommufd: Introduce auto domain creation
vfio/ccw: Don't initialize HOST_IOMMU_DEVICE with mdev
vfio/ap: Don't initialize HOST_IOMMU_DEVICE with mdev
vfio/iommufd: Return errno in iommufd_cdev_attach_ioas_hwpt()
backends/iommufd: Extend iommufd_backend_get_device_info() to fetch HW capabilities
vfio/iommufd: Don't initialize nor set a HOST_IOMMU_DEVICE with mdev
vfio/pci: Extract mdev check into an helper
hw/vfio/container: Fix SIGSEV on vfio_container_instance_finalize()
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
* hpet: emulation improvements
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmaelL4UHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroMXoQf+K77lNlHLETSgeeP3dr7yZPOmXjjN
qFY/18jiyLw7MK1rZC09fF+n9SoaTH8JDKupt0z9M1R10HKHLIO04f8zDE+dOxaE
Rou3yKnlTgFPGSoPPFr1n1JJfxtYlLZRoUzaAcHUaa4W7JR/OHJX90n1Rb9MXeDk
jV6P0v1FWtIDdM6ERm9qBGoQdYhj6Ra2T4/NZKJFXwIhKEkxgu4yO7WXv8l0dxQz
jE4fKotqAvrkYW1EsiVZm30lw/19duhvGiYeQXoYhk8KKXXjAbJMblLITSNWsCio
3l6Uud/lOxekkJDAq5nH3H9hCBm0WwvwL+0vRf3Mkr+/xRGvrhtmUdp8NQ==
=00mB
-----END PGP SIGNATURE-----
Merge tag 'for-upstream' of https://gitlab.com/bonzini/qemu into staging
* target/i386/kvm: support for reading RAPL MSRs using a helper program
* hpet: emulation improvements
# -----BEGIN PGP SIGNATURE-----
#
# iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmaelL4UHHBib256aW5p
# QHJlZGhhdC5jb20ACgkQv/vSX3jHroMXoQf+K77lNlHLETSgeeP3dr7yZPOmXjjN
# qFY/18jiyLw7MK1rZC09fF+n9SoaTH8JDKupt0z9M1R10HKHLIO04f8zDE+dOxaE
# Rou3yKnlTgFPGSoPPFr1n1JJfxtYlLZRoUzaAcHUaa4W7JR/OHJX90n1Rb9MXeDk
# jV6P0v1FWtIDdM6ERm9qBGoQdYhj6Ra2T4/NZKJFXwIhKEkxgu4yO7WXv8l0dxQz
# jE4fKotqAvrkYW1EsiVZm30lw/19duhvGiYeQXoYhk8KKXXjAbJMblLITSNWsCio
# 3l6Uud/lOxekkJDAq5nH3H9hCBm0WwvwL+0vRf3Mkr+/xRGvrhtmUdp8NQ==
# =00mB
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 23 Jul 2024 03:19:58 AM AEST
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
* tag 'for-upstream' of https://gitlab.com/bonzini/qemu:
hpet: avoid timer storms on periodic timers
hpet: store full 64-bit target value of the counter
hpet: accept 64-bit reads and writes
hpet: place read-only bits directly in "new_val"
hpet: remove unnecessary variable "index"
hpet: ignore high bits of comparator in 32-bit mode
hpet: fix and cleanup persistence of interrupt status
Add support for RAPL MSRs in KVM/Qemu
tools: build qemu-vmsr-helper
qio: add support for SO_PEERCRED for socket channel
target/i386: do not crash if microvm guest uses SGX CPUID leaves
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
ioctl(iommufd, IOMMU_HWPT_GET_DIRTY_BITMAP, arg) is the UAPI
that fetches the bitmap that tells what was dirty in an IOVA
range.
A single bitmap is allocated and used across all the hwpts
sharing an IOAS which is then used in log_sync() to set Qemu
global bitmaps.
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
ioctl(iommufd, IOMMU_HWPT_SET_DIRTY_TRACKING, arg) is the UAPI that
enables or disables dirty page tracking. The ioctl is used if the hwpt
has been created with dirty tracking supported domain (stored in
hwpt::flags) and it is called on the whole list of iommu domains.
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Store the value of @caps returned by iommufd_backend_get_device_info()
in a new field HostIOMMUDeviceCaps::hw_caps. Right now the only value is
whether device IOMMU supports dirty tracking (IOMMU_HW_CAP_DIRTY_TRACKING).
This is in preparation for HostIOMMUDevice::realize() being called early
during attach_device().
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Remove caps::aw_bits which requires the bcontainer::iova_ranges being
initialized after device is actually attached. Instead defer that to
.get_cap() and call vfio_device_get_aw_bits() directly.
This is in preparation for HostIOMMUDevice::realize() being called early
during attach_device().
Suggested-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
There's generally two modes of operation for IOMMUFD:
1) The simple user API which intends to perform relatively simple things
with IOMMUs e.g. DPDK. The process generally creates an IOAS and attaches
to VFIO and mainly performs IOAS_MAP and UNMAP.
2) The native IOMMUFD API where you have fine grained control of the
IOMMU domain and model it accordingly. This is where most new feature
are being steered to.
For dirty tracking 2) is required, as it needs to ensure that
the stage-2/parent IOMMU domain will only attach devices
that support dirty tracking (so far it is all homogeneous in x86, likely
not the case for smmuv3). Such invariant on dirty tracking provides a
useful guarantee to VMMs that will refuse incompatible device
attachments for IOMMU domains.
Dirty tracking insurance is enforced via HWPT_ALLOC, which is
responsible for creating an IOMMU domain. This is contrast to the
'simple API' where the IOMMU domain is created by IOMMUFD automatically
when it attaches to VFIO (usually referred as autodomains) but it has
the needed handling for mdevs.
To support dirty tracking with the advanced IOMMUFD API, it needs
similar logic, where IOMMU domains are created and devices attached to
compatible domains. Essentially mimicking kernel
iommufd_device_auto_get_domain(). With mdevs given there's no IOMMU domain
it falls back to IOAS attach.
The auto domain logic allows different IOMMU domains to be created when
DMA dirty tracking is not desired (and VF can provide it), and others where
it is. Here it is not used in this way given how VFIODevice migration
state is initialized after the device attachment. But such mixed mode of
IOMMU dirty tracking + device dirty tracking is an improvement that can
be added on. Keep the 'all of nothing' of type1 approach that we have
been using so far between container vs device dirty tracking.
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
[ clg: Added ERRP_GUARD() in iommufd_cdev_autodomains_get() ]
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
The helper will be able to fetch vendor agnostic IOMMU capabilities
supported both by hardware and software. Right now it is only iommu dirty
tracking.
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
SPDM enables authentication, attestation and key exchange to assist in
providing infrastructure security enablement. It's a standard published
by the DMTF [1].
SPDM supports multiple transports, including PCIe DOE and MCTP.
This patch adds support to QEMU to connect to an external SPDM
instance.
SPDM support can be added to any QEMU device by exposing a
TCP socket to a SPDM server. The server can then implement the SPDM
decoding/encoding support, generally using libspdm [2].
This is similar to how the current TPM implementation works and means
that the heavy lifting of setting up certificate chains, capabilities,
measurements and complex crypto can be done outside QEMU by a well
supported and tested library.
1: https://www.dmtf.org/standards/SPDM
2: https://github.com/DMTF/libspdm
Signed-off-by: Huai-Cheng Kuo <hchkuo@avery-design.com.tw>
Signed-off-by: Chris Browy <cbrowy@avery-design.com>
Co-developed-by: Jonathan Cameron <Jonathan.cameron@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
[ Changes by WM
- Bug fixes from testing
]
Signed-off-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
[ Changes by AF:
- Convert to be more QEMU-ified
- Move to backends as it isn't PCIe specific
]
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20240703092027.644758-3-alistair.francis@wdc.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
KVM vCPU creation is done once during the vCPU realization when Qemu vCPU thread
is spawned. This is common to all the architectures as of now.
Hot-unplug of vCPU results in destruction of the vCPU object in QOM but the
corresponding KVM vCPU object in the Host KVM is not destroyed as KVM doesn't
support vCPU removal. Therefore, its representative KVM vCPU object/context in
Qemu is parked.
Refactor architecture common logic so that some APIs could be reused by vCPU
Hotplug code of some architectures likes ARM, Loongson etc. Update new/old APIs
with trace events. New APIs qemu_{create,park,unpark}_vcpu() can be externally
called. No functional change is intended here.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Tested-by: Vishnu Pajjuri <vishnu@os.amperecomputing.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Xianglai Li <lixianglai@loongson.cn>
Tested-by: Miguel Luis <miguel.luis@oracle.com>
Reviewed-by: Shaoqin Huang <shahuang@redhat.com>
Reviewed-by: Vishnu Pajjuri <vishnu@os.amperecomputing.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Tested-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20240716111502.202344-2-salil.mehta@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Starting with the "Sandy Bridge" generation, Intel CPUs provide a RAPL
interface (Running Average Power Limit) for advertising the accumulated
energy consumption of various power domains (e.g. CPU packages, DRAM,
etc.).
The consumption is reported via MSRs (model specific registers) like
MSR_PKG_ENERGY_STATUS for the CPU package power domain. These MSRs are
64 bits registers that represent the accumulated energy consumption in
micro Joules. They are updated by microcode every ~1ms.
For now, KVM always returns 0 when the guest requests the value of
these MSRs. Use the KVM MSR filtering mechanism to allow QEMU handle
these MSRs dynamically in userspace.
To limit the amount of system calls for every MSR call, create a new
thread in QEMU that updates the "virtual" MSR values asynchronously.
Each vCPU has its own vMSR to reflect the independence of vCPUs. The
thread updates the vMSR values with the ratio of energy consumed of
the whole physical CPU package the vCPU thread runs on and the
thread's utime and stime values.
All other non-vCPU threads are also taken into account. Their energy
consumption is evenly distributed among all vCPUs threads running on
the same physical CPU package.
To overcome the problem that reading the RAPL MSR requires priviliged
access, a socket communication between QEMU and the qemu-vmsr-helper is
mandatory. You can specified the socket path in the parameter.
This feature is activated with -accel kvm,rapl=true,path=/path/sock.sock
Actual limitation:
- Works only on Intel host CPU because AMD CPUs are using different MSR
adresses.
- Only the Package Power-Plane (MSR_PKG_ENERGY_STATUS) is reported at
the moment.
Signed-off-by: Anthony Harivel <aharivel@redhat.com>
Link: https://lore.kernel.org/r/20240522153453.1230389-4-aharivel@redhat.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This callback will be used to retrieve the page size mask supported
along a given Host IOMMU device.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
The error handle argument is not used anywhere. let's remove it.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Shutdown requests are normally hardware dependent.
By extending pvpanic to also handle shutdown requests, guests can
submit such requests with an easily implementable and cross-platform
mechanism.
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Thomas Weißschuh <thomas@t-8ch.de>
Message-Id: <20240527-pvpanic-shutdown-v8-5-5a28ec02558b@t-8ch.de>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Store the aliased bus and devfn in the HostIOMMUDevice.
This will be useful to handle info that are iommu group
specific and not device specific (such as reserved
iova ranges).
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Introduce a new HostIOMMUDevice callback that allows to
retrieve the usable IOVA ranges.
Implement this callback in the legacy VFIO and IOMMUFD VFIO
host iommu devices. This relies on the VFIODevice agent's
base container iova_ranges resource.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Store the agent device (VFIO or VDPA) in the host IOMMU device.
This will allow easy access to some of its resources.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Introduce a helper function iommufd_backend_get_device_info() to get
host IOMMU related information through iommufd uAPI.
Signed-off-by: Yi Liu <yi.l.liu@intel.com>
Signed-off-by: Yi Sun <yi.y.sun@linux.intel.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
TYPE_HOST_IOMMU_DEVICE_IOMMUFD represents a host IOMMU device under
iommufd backend. It is abstract, because it is going to be derived
into VFIO or VDPA type'd device.
It will have its own .get_cap() implementation.
TYPE_HOST_IOMMU_DEVICE_IOMMUFD_VFIO is a sub-class of
TYPE_HOST_IOMMU_DEVICE_IOMMUFD, represents a VFIO type'd host IOMMU
device under iommufd backend. It will be created during VFIO device
attaching and passed to vIOMMU.
It will have its own .realize() implementation.
Opportunistically, add missed header to include/sysemu/iommufd.h.
Suggested-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Yi Liu <yi.l.liu@intel.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
HostIOMMUDeviceCaps's elements map to the host IOMMU's capabilities.
Different platform IOMMU can support different elements.
Currently only two elements, type and aw_bits, type hints the host
platform IOMMU type, i.e., INTEL vtd, ARM smmu, etc; aw_bits hints
host IOMMU address width.
Introduce .get_cap() handler to check if HOST_IOMMU_DEVICE_CAP_XXX
is supported.
Suggested-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
A HostIOMMUDevice is an abstraction for an assigned device that is protected
by a physical IOMMU (aka host IOMMU). The userspace interaction with this
physical IOMMU can be done either through the VFIO IOMMU type 1 legacy
backend or the new iommufd backend. The assigned device can be a VFIO device
or a VDPA device. The HostIOMMUDevice is needed to interact with the host
IOMMU that protects the assigned device. It is especially useful when the
device is also protected by a virtual IOMMU as this latter use the translation
services of the physical IOMMU and is constrained by it. In that context the
HostIOMMUDevice can be passed to the virtual IOMMU to collect physical IOMMU
capabilities such as the supported address width. In the future, the virtual
IOMMU will use the HostIOMMUDevice to program the guest page tables in the
first translation stage of the physical IOMMU.
Introduce .realize() to initialize HostIOMMUDevice further after instance init.
Suggested-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
This generalises the qtest_clock_warp code to use the AccelOps
handlers for updating its own sense of time. This will make the next
patch which moves the warp code closer to pure code motion.
From: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Pierrick Bouvier <pierrick.bouvier@linaro.org>
Message-Id: <20240530220610.1245424-3-pierrick.bouvier@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240620152220.2192768-6-alex.bennee@linaro.org>
We are about to remove direct calls to individual accelerators for
this information and will need a central point for plugins to hook
into time changes.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Pierrick Bouvier <pierrick.bouvier@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240530220610.1245424-2-pierrick.bouvier@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240620152220.2192768-5-alex.bennee@linaro.org>
Add a second mapcache for grant mappings. The mapcache for
grants needs to work with XC_PAGE_SIZE granularity since
we can't map larger ranges than what has been granted to us.
Like with foreign mappings (xen_memory), machines using grants
are expected to initialize the xen_grants MR and map it
into their address-map accordingly.
CC: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Pass the ram_addr offset to xen_map_cache.
This is in preparation for adding grant mappings that need
to compute the address within the RAMBlock.
No functional changes.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
When a macOS Hypervisor.framework call fails which is checked by
assert_hvf_ok(), Qemu exits printing the error value, but not the
location
in the code, as regular assert() macro expansions would.
This change turns assert_hvf_ok() into a macro similar to other
assertions, which expands to a call to the corresponding _impl()
function together with information about the expression that failed
the assertion and its location in the code.
Additionally, stringifying the numeric hv_return_t code is factored
into a helper function that can be reused for diagnostics and debugging
outside of assertions.
Signed-off-by: Phil Dennis-Jordan <phil@philjordan.eu>
Message-ID: <20240605112556.43193-8-phil@philjordan.eu>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
macOS Hypervisor.framework uses different types for identifying vCPUs, hv_vcpu_t or hv_vcpuid_t, depending on host architecture. They are not just differently named typedefs for the same primitive type, but reference different-width integers.
Instead of using an integer type and casting where necessary, this change introduces a typedef which resolves the active architecture’s hvf typedef. It also removes a now-unnecessary cast.
Signed-off-by: Phil Dennis-Jordan <phil@philjordan.eu>
Reviewed-by: Roman Bolshakov <roman@roolebo.dev>
Tested-by: Roman Bolshakov <roman@roolebo.dev>
Message-ID: <20240605112556.43193-4-phil@philjordan.eu>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If memory-backend-{file,ram} has a size that's not aligned to
underlying page size it is not only wasteful, but also may lead
to hard to debug behaviour. For instance, in case
memory-backend-file and hugepages, madvise() and mbind() fail.
Rightfully so, page is the smallest unit they can work with. And
even though an error is reported, the root cause it not very
clear:
qemu-system-x86_64: Couldn't set property 'dump' on 'memory-backend-file': Invalid argument
After this commit:
qemu-system-x86_64: backend 'memory-backend-file' memory size must be multiple of 2 MiB
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Message-ID: <b5b9f9c6bba07879fb43f3c6f496c69867ae3716.1717584048.git.mprivozn@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add xen_mr_is_memory() to abstract away tests for the
xen_memory MR.
No functional changes.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240529140739.1387692-4-edgar.iglesias@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This is to follow the coding standand to return bool if 'Error **'
is used to pass error.
The changed functions include:
iommufd_backend_connect
iommufd_backend_alloc_ioas
By this chance, simplify the functions a bit by avoiding duplicate
recordings, e.g., log through either error interface or trace, not
both.
Suggested-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Introduce a new Kconfig symbol, CONFIG_DEVICE_TREE, that specifies whether
to include the common device tree code in system/device_tree.c and to
link to libfdt. For now, include it unconditionally if libfdt is
available.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
