This helps simplify the existing implementation.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-31-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
There are two cases here: the first is when the TI command underflows, in which
case we raise INTR_BS to indicate an early change of phase, and the second is
when the TI command overflows because the host requested a transfer for more
data than is available. In the latter case force TC to zero so that the TI
completion logic executes correctly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-30-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Ensure that the async_len checks for requesting data from the SCSI layer and
the TC == 0 checks to detect the end of the DMA transfer are consistent in both
do_dma_pdma_cb() and esp_do_dma(). In particular this involves adding the check
to see if the FIFO is at its low threshold since PDMA and mixed DMA and non-DMA
requests can leave data remaining in the FIFO.
At the same time update all the comments so that they are also consistent between
all similar code paths.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-29-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Since esp_dma_done() is called in both cases, and ti_size cannot be zero
(otherwise esp_command_complete() would have been called instead), replace
the conditional logic with a single call to esp_dma_done().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-28-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The following ti_cmd checks ensure that only DMA and non-DMA TI commmands will
can call into the esp_do_dma() and esp_do_nodma() callbacks.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-27-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
With the latest changes this condition cannot occur anymore and so the logic
can be completely removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-26-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Now that the TC is updated for each PDMA access (rather than once the FIFO is
full) there is no need to adjust the TC at start of each DMA transfer if the
FIFO is not empty.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-25-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
In the case when more data is requested from the SCSI layer during a DMA data
transfer from a device, don't immediately fall through to the TC check logic.
Otherwise when TC is zero INTR_BS will be raised immediately rather than when
the next set of SCSI data is ready.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-24-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Rather than wait for the FIFO to fill up before calling the PDMA callback, push
that logic directly into the from_device logic in do_dma_pdma_cb().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-23-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Ensure that esp_dma_done() is only called when TC is zero, which is currently
always the case for DMA transfers.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-22-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
No change to the condition itself, other than to clarify that esp_dma_done()
must be called when TC is zero.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-21-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The TI end of transfer interrupt only occurs when the TC reaches zero and is
not related to the SCSI layer transfer.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-20-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The internal state of the ESP sequencer is not affected when raising an interrupt
to indicate the end of a DMA transfer.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-19-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
There is no need to manually reset these values as the ESP emulation now
correctly handles them within its existing logic.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-18-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This workaround is no longer required with the current code and so can be
removed.
[Note: whilst MacOS itself can boot correctly, removing this hack prevents
a bootable EMILE CDROM from working. This is caused by a separate bug which
will be fixed by a subsequent patch]
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-17-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Following on from the recent changes to when the TC is updated, it is now
possible to remove another set of manual STAT_TC updates so that its state
is now managed within esp_set_tc().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-16-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This function is used to set the current SCSI bus phase in the ESP_RSTAT register
without affecting any of flag bits.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-15-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This is to ensure that STAT_TC is triggered during the right parts of the
transfer when it is controlled exclusively by the TC.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-14-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Instead accumulate in the real FIFO as done in real hardware, and then transfer
to cmdfifo when we're ready to process the MESSAGE OUT and COMMAND phase data.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-13-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The do_cmd variable is only set for the MESSAGE OUT and COMMAND phases i.e.
those which involve transfers from the host to the SCSI bus, and so the unused
case can be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-12-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The ultimate aim is to for esp_do_dma() behaviour to be determined by the SCSI
bus phase, in which case it is necessary to have separate to/from device paths.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-11-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Invert the logic so that the end of DMA transfer check becomes one that checks
for TC == 0 in the from device path in do_dma_pdma_cb().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This helps to simplify esp_reg_write() and potentially allows for a 2-level
deep FIFO to be implemented in future.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-9-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This should be exclusively managed by esp_set_tc() rather than being manually
set in multiple places. Start by removing the occurrences exclusive to PDMA
and command completion which are those that can be currently removed without
affecting any test images.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This flag is set once the transfer counter counts down to zero.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Since the DREQ value depends upon the result of the selection process, add a
workaround to each esp_select() to manually assert DREQ durring the MESSAGE OUT
and COMMAND phases.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The FIFO contents should not be affected by performing SCSI target selection.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The fifo8_pop_buf() function returns a pointer to the FIFO buffer up to the
specified length. Since the FIFO buffer is modelled as an array then once
the FIFO wraps around, only the continuous portion of the buffer can be
returned.
In future the use of continuous and unaligned accesses will advance the
internal FIFO head pointer, so modify esp_fifo_pop_buf() to ensure that
any wraparound content is also returned up to the requested length.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Since get_cmd() can be called multiple times during a mixed FIFO/DMA request,
move the existing request cancel check into esp_select() which always occurs
at the start of new SCSI request.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The FIFO contents should not be affected if the target selection fails.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Correct arithmetic for separating high and low
on a large negative number.
Cc: qemu-stable@nongnu.org
Fixes: 79ffece444 ("tcg/arm: Implement direct branch for goto_tb")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1714
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
We need values 0-3 for TCG_TYPE_I128 on 32-bit hosts.
Cc: qemu-stable@nongnu.org
Fixes: 43eef72f41 ("tcg: Add temp allocation for TCGv_i128")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2159
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Tested-by: Michael Tokarev <mjt@tls.msk.ru>
Some enhancements and fixes for the hppa target.
The major change is, that this patchset adds a new SeaBIOS-hppa firmware
which is built as 32- and 64-bit firmware.
The new 64-bit firmware is necessary to fully support 64-bit operating systems
(HP-UX, Linux, NetBSD,...).
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCZcquAQAKCRD3ErUQojoP
X9pjAQCVsWyuYlGCW2paIGVWKV0vsOpwetUrbhRtFUZGqZxb4AD9FbMsXRcCN/oq
CotBPY/a8MEzIQcwYl5QbcI5nNW4ygs=
=RA0B
-----END PGP SIGNATURE-----
Merge tag 'hppa64-pull-request' of https://github.com/hdeller/qemu-hppa into staging
target/hppa: Enhancements and fixes
Some enhancements and fixes for the hppa target.
The major change is, that this patchset adds a new SeaBIOS-hppa firmware
which is built as 32- and 64-bit firmware.
The new 64-bit firmware is necessary to fully support 64-bit operating systems
(HP-UX, Linux, NetBSD,...).
# -----BEGIN PGP SIGNATURE-----
#
# iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCZcquAQAKCRD3ErUQojoP
# X9pjAQCVsWyuYlGCW2paIGVWKV0vsOpwetUrbhRtFUZGqZxb4AD9FbMsXRcCN/oq
# CotBPY/a8MEzIQcwYl5QbcI5nNW4ygs=
# =RA0B
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 12 Feb 2024 23:47:13 GMT
# gpg: using EDDSA key BCE9123E1AD29F07C049BBDEF712B510A23A0F5F
# gpg: Good signature from "Helge Deller <deller@gmx.de>" [unknown]
# gpg: aka "Helge Deller <deller@kernel.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 4544 8228 2CD9 10DB EF3D 25F8 3E5F 3D04 A7A2 4603
# Subkey fingerprint: BCE9 123E 1AD2 9F07 C049 BBDE F712 B510 A23A 0F5F
* tag 'hppa64-pull-request' of https://github.com/hdeller/qemu-hppa:
hw/hppa/machine: Load 64-bit firmware on 64-bit machines
target/hppa: Update SeaBIOS-hppa to version 16
hw/net/tulip: add chip status register values
target/hppa: PDC_BTLB_INFO uses 32-bit ints
target/hppa: Allow read-access to PSW with rsm 0,reg instruction
lasi: Add reset I/O ports for LASI audio and FDC
target/hppa: Implement do_transaction_failed handler for I/O errors
lasi: allow access to LAN MAC address registers
hw/pci-host/astro: Implement Hard Fail and Soft Fail mode
hw/pci-host/astro: Avoid aborting on access failure
target/hppa: Add "diag 0x101" for console output support
disas/hppa: Add disassembly for qemu specific instructions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Include "exec/memory.h" in order to avoid:
monitor/hmp-cmds-target.c:263:10: error: call to undeclared function 'memory_region_is_ram';
ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
if (!memory_region_is_ram(mrs.mr) && !memory_region_is_romd(mrs.mr)) {
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Include "exec/memory.h" in order to avoid:
cpu-target.c:201:50: error: use of undeclared identifier 'TYPE_MEMORY_REGION'
DEFINE_PROP_LINK("memory", CPUState, memory, TYPE_MEMORY_REGION,
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This file is only used by system/physmem.c so move them together.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The detailed help lists zoom-to-fit as valid option but it is missing
from the short option summary. Add it there too.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
'a == b ? false : true' is a rather convoluted way of writing 'a != b'.
Use the more obvious way to write it.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit aa09b3d5f8 (stats: Move QMP commands from monitor/ to stats/)
created section Stats, but neglected to add qapi/stats.json to it.
Fix that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit 415442a1b4 (hw/mem/cxl_type3: Add CXL RAS Error Injection
Support.) created qapi/cxl.json without adding it to MAINTAINERS. Fix
that.
Cc: Ben Widawsky <ben.widawsky@intel.com>
Cc: Jonathan Cameron <jonathan.cameron@huawei.com>
Cc: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
qemu_smbios_type8_opts did not have the list terminator and that
resulted in out-of-bound memory access. It also needs to have an element
for the type option.
Cc: qemu-stable@nongnu.org
Fixes: fd8caa253c ("hw/smbios: support for type 8 (port connector)")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
qemu_smbios_type11_opts did not have the list terminator and that
resulted in out-of-bound memory access. It also needs to have an element
for the type option.
Cc: qemu-stable@nongnu.org
Fixes: 2d6dcbf93f ("smbios: support setting OEM strings table")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Use device_class_set_parent_realize() to set parent realize() directly.
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Use device_class_set_parent_realize() to set parent realize() directly.
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Use device_class_set_parent_realize() to set parent realize() directly.
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Use device_class_set_parent_realize() to set parent realize() directly.
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
