Split qemu_savevm_state_begin to:
qemu_savevm_state_header That writes the initial file header.
qemu_savevm_state_begin That sets up devices and does the first
device pass.
Used later in postcopy.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
and use it in loadvm_state and ram_load.
Where ever it's used, check the return and error if it failed.
Minor: ram_load was using a 257 byte array for its string, the
maximum length is 255 bytes + 0 terminator, so fix to 256
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
We create optional sections with this patch. But we already have
optional subsections. Instead of having two mechanism that do the
same, we can just generalize it.
For subsections we just change:
- Add a needed function to VMStateDescription
- Remove VMStateSubsection (after removal of the needed function
it is just a VMStateDescription)
- Adjust the whole tree, moving the needed function to the corresponding
VMStateDescription
Signed-off-by: Juan Quintela <quintela@redhat.com>
This way, we will put savevm global state here, instead of lots of variables.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
We assign the MIGRATION_STATUS_SETUP status in two places. Just in
succession. Just remove the second one.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Qemu crashes when IPv6 address is specified for migration and access
to any RDMA uverbs device available on the system is blocked using cgroups.
Fix the crash by checking the return value of ibv_open_device routine.
Signed-off-by: Meghana Cheripady <meghana.cheripady@avagotech.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
There are two places that define 'len' variable, It's OK for compiling,
but makes it difficult for reading.
Remove the local one which defined in the inside 'while' loop.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
To make changes easier, with the copy, I maintained almost all include
files. Now I remove the unnecessary ones on this patch. This compiles
on linux x64 with all architectures configured, and cross-compiles for
windows 32 and 64 bits.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
If anyone feels like adding himself to the list, just sent me a patch.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
For historic reasons, ram migration have been on arch_init.c. Just
split it into migration/ram.c, the same that happened with block.c.
There is only code movement, no changes altogether.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Add the qmp commands to tune and query the parameters used in live
migration.
Signed-off-by: Liang Li <liang.z.li@intel.com>
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Put the three parameters related to multiple thread (de)compression
into an int array, and use an enum type to index the parameter.
Signed-off-by: Liang Li <liang.z.li@intel.com>
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The multiple compression threads can be turned on/off through
qmp and hmp interface before doing live migration.
Signed-off-by: Liang Li <liang.z.li@intel.com>
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>
Reviewed-by: Dr.David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
qemu_put_compression_data() compress the data and put it to QEMUFile.
qemu_put_qemu_file() put the data in the buffer of source QEMUFile to
destination QEMUFile.
Signed-off-by: Liang Li <liang.z.li@intel.com>
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Add the code to create and destroy the multiple threads those will be
used to do data decompression. Left some functions empty just to keep
clearness, and the code will be added later.
Signed-off-by: Liang Li <liang.z.li@intel.com>
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>
Reviewed-by: Dr.David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Add the code to create and destroy the multiple threads those will
be used to do data compression. Left some functions empty to keep
clearness, and the code will be added later.
Signed-off-by: Liang Li <liang.z.li@intel.com>
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>
Reviewed-by: Dr.David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
We often don't need the BlockDriverState for functions
that operate on bitmaps. Remove it.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1429314609-29776-15-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This field will be set for user created dirty bitmap. Also pass in an
error pointer to bdrv_create_dirty_bitmap, so when a name is already
taken on this BDS, it can report an error message. This is not global
check, two BDSes can have dirty bitmap with a common name.
Implemented bdrv_find_dirty_bitmap to find a dirty bitmap by name, will
be used later when other QMP commands want to reference dirty bitmap by
name.
Add bdrv_dirty_bitmap_make_anon. This unsets the name of dirty bitmap.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1429314609-29776-3-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
As part of commit e325b49a32,
order in which resources are destroyed was changed for fixing
a seg fault. Due to this change, CQ will never get destroyed as
CQ should be destroyed after QP destruction. Seg fault is caused
improper cleanup when connection fails. Fixing cleanup after
connection failure and order in which resources are destroyed
in qemu_rdma_cleanup() routine.
Signed-off-by: Meghana Cheripady <meghana.cheripady@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
'cancelling' status was introduced by commit 51cf4c1a, mainly to avoid a
possible start of a new migration process while the previous one still exists.
But we didn't expose this status to user, instead we returned the 'active' state.
Here, we expose it to the user (such as libvirt), 'cancelling' status only
occurs for a short window before the migration aborts, so for users,
if they cancel a migration process, it will observe 'cancelling' status
occasionally.
Testing revealed that with older libvirt (anything 1.2.13 or less) will
print an odd error message if the state is seen, but that the migration
is still properly cancelled. Newer libvirt will be patched to recognize
the new state without the odd error message.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Cc: libvir-list@redhat.com
Signed-off-by: Juan Quintela <quintela@redhat.com>
The original 'status' is an open-coded 'str' type, convert it to use an
enum type.
This conversion is backwards compatible, better documented and
more convenient for future extensibility.
In addition, Fix a typo for qapi-schema.json (just remove the typo) :
s/'completed'. 'comppleted' (since 1.2)/'completed' (since 1.2)
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Rename all macro MIG_STATE_* to MIGRATION_STATUS_* except "MIG_STATE_ERROR",
we rename it to "MIGRATION_STATUS_FAILED" which will match the migration status
string 'failed'.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
migrate_rdma_pin_all() and qsb_clone() are completely unused and thus
can be deleted.
Signed-off-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Cc: Juan Quintela <quintela@redhat.com>
Cc: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Create a separate error for the case where migrate_incoming is
used after a succesful migrate_incoming.
Reword the error in the case where '-incoming defer' is missing
to omit the command name so it's right for both hmp and qmp.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Fix type casts between pointers and 64 bit integers.
Now 32 bit builds are possible again.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The current code won't compile on 32 bit hosts because there are lots
of type casts between pointers and 64 bit integers.
Fix some of them.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Do not check for rdma->host being empty twice. This removes a large
"if" block, so code indentation is changed. While at it, remove an
ugly goto from the loop, replacing it with a cleaner if logic. And
finally, there's no need to initialize `ret' variable since is always
has a value.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Tested-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
--
fixed space detected by Dave
Signed-off-by: Juan Quintela <quintela@redhat.com>
qerror_report_err() is a transitional interface to help with
converting existing monitor commands to QMP. It should not be used
elsewhere. Replace by error_report_err() in
process_incoming_migration_co().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
It used to be an int, but then we can't pass directly the
bytes_transferred parameter, that would happen later in the series.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Add migrate_incoming/migrate-incoming to start an incoming
migration.
Once a qemu has been started with
-incoming defer
the migration can be started by issuing:
migrate_incoming uri
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
-incoming defer causes qemu to wait for an incoming migration
to be specified later. The monitor can be used to set migration
capabilities that may affect the incoming connection process.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
* Remove trailing whitespace (fixes 9 errors from checkpatch.pl).
One comment line was longer than 80 characters, so wrap it
and fix a typo, too.
* Replace tabs by blanks (fixes 1 error).
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
It looks like the dtrace trace code gets upset if you have trace names
with __ in, which the migration/rdma.c code does.
Rename the functions and the associated traces.
Fixes: 733252deb8
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reported-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Message-id: 1424105885-12149-1-git-send-email-dgilbert@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Warnings from the Sparse static analysis tool:
migration-rdma.c:151:12: warning:
symbol 'wrid_desc' was not declared. Should it be static?
migration-rdma.c:190:12: warning:
symbol 'control_desc' was not declared. Should it be static?
migration-rdma.c:3301:19: warning:
symbol 'rdma_read_ops' was not declared. Should it be static?
migration-rdma.c:3308:19: warning:
symbol 'rdma_write_ops' was not declared. Should it be static?
Cc: Juan Quintela <quintela@redhat.com>
Cc: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Turn all the D/DD/DDDPRINTFs into trace events
Turn most of the fprintf(stderr, into error_report
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
One of the annoyances of the current migration format is the fact that
it's not self-describing. In fact, it's not properly describing at all.
Some code randomly scattered throughout QEMU elaborates roughly how to
read and write a stream of bytes.
We discussed an idea during KVM Forum 2013 to add a JSON description of
the migration protocol itself to the migration stream. This patch
adds a section after the VM_END migration end marker that contains
description data on what the device sections of the stream are composed of.
This approach is backwards compatible with any QEMU version reading the
stream, because QEMU just stops reading after the VM_END marker and ignores
any data following it.
With an additional external program this allows us to decipher the
contents of any migration stream and hopefully make migration bugs easier
to track down.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
For ftell we flush the output buffer to ensure that we don't have anything
lingering in our internal buffers. This is a very safe thing to do.
However, with the dynamic size measurement that the dynamic vmstate
description will bring this would turn out quite slow.
Instead, we can fast path this specific measurement and just take the
internal buffers into account when telling the kernel our position.
I'm sure I overlooked some corner cases where this doesn't work, so
instead of tuning the safe, existing version, this patch adds a fast
variant of ftell that gets used by the dynamic vmstate description code
which isn't critical when it fails.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Mostly on the load side, so that when we get a complaint about
a migration failure we can figure out what it didn't like.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Convert a bunch of fprintfs to error_reports
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Force shutdown on migration socket on cancel to cause the cancel
to complete even if the socket is blocked on a dead network.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
libvirt prefers opening the TCP connection itself, for two reasons.
First, connection failed errors can be detected easier, without having
to parse qemu's error output.
Second, libvirt might be asked to secure the transfer by tunnelling the
communication through an TLS layer.
Therefore, libvirt opens the TCP connection itself and passes an FD to qemu
using QMP and a POSIX-specific mechanism.
Hence, in order to make the reverse-path work in such cases, qemu needs to
distinguish if the transmitted FD is a socket (reverse-path available)
or not (reverse-path might not be available) and use the corresponding
abstraction.
Signed-off-by: Cristian Klein <cristian.klein@cs.umu.se>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Add QEMUFile interface to allow a socket to be 'shut down' - i.e. any
reads/writes will fail (and any blocking read/write will be woken).
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Only free qsb that qemu_bufopen allocated, and also allow
qemu_bufopen accept qsb as input for write operation. It
will make the API more logical:
1.If you create the QEMUSizedBuffer yourself, you need to
free it by using qsb_free() but not depends on other API
like qemu_fclose.
2.allow qemu_bufopen() accept QEMUSizedBuffer as input for
write operation, otherwise, it will be a little strange
for this API won't accept the second parameter.
This brings API change, since there are only 3
users of this API currently, this change only impact the
first one which will be fixed in patch 2 of this patchset,
so I think it is safe to do this change.
1 70 tests/test-vmstate.c <<open_mem_file_read>>
return qemu_bufopen("r", qsb);
2 404 tests/test-vmstate.c <<test_save_noskip>>
QEMUFile *fsave = qemu_bufopen("w", NULL);
3 424 tests/test-vmstate.c <<test_save_skip>>
QEMUFile *fsave = qemu_bufopen("w", NULL);
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Juan Quintela <quintela@redhat.com>
Cc: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Add a cast in qemu_get_be32() to avoid shifting left into the sign
bit of a signed integer (which is undefined behaviour in C).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
