When a bare-metal application on the raspi3 board reads the
AUX_MU_STAT_REG MMIO register while the device's buffer is
at full receive FIFO capacity
(i.e. `s->read_count == BCM2835_AUX_RX_FIFO_LEN`) the
assertion `assert(s->read_count < BCM2835_AUX_RX_FIFO_LEN)`
fails.
Reported-by: Cryptjar <cryptjar@junk.studio>
Suggested-by: Cryptjar <cryptjar@junk.studio>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/459
Signed-off-by: Frederik van Hövell <frederik@fvhovell.nl>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
[PMM: commit message tweaks]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move the property types and property macros implemented in
qdev-properties-system.c to a new qdev-properties-system.h
header.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-16-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The "BCM2835 ARM Peripherals" datasheet [*] chapter 2
("Auxiliaries: UART1 & SPI1, SPI2"), list the register
sizes as 3/8/16/32 bits. We assume this means this
peripheral allows 8-bit accesses.
This was not an issue until commit 5d971f9e67 which reverted
("memory: accept mismatching sizes in memory_region_access_valid").
The model is implemented as 32-bit accesses (see commit 97398d900c,
all registers are 32-bit) so replace MemoryRegionOps.valid as
MemoryRegionOps.impl, and re-introduce MemoryRegionOps.valid
with a 8/32-bit range.
[*] https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
Fixes: 97398d900c ("bcm2835_aux: add emulation of BCM2835 AUX (aka UART1) block")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201002181032.1899463-1-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Various logging improvements as once:
- Use 0x prefix for hex numbers
- Display value written during write accesses
- Move some logs from GUEST_ERROR to UNIMP
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Cleber Rosa <crosa@redhat.com>
Message-id: 20190926173428.10713-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
RX and TX interrupt bits were reversed, resulting in an endless sequence
of serial interupts in the emulated system and the following repeated
error message when booting Linux.
serial8250: too much work for irq61
This results in a boot failure most of the time.
Qemu command line used to reproduce the problem:
qemu-system-aarch64 -M raspi3 -m 1024 \
-kernel arch/arm64/boot/Image \
--append "rdinit=/sbin/init console=ttyS1,115200"
-initrd rootfs.cpio \
-dtb arch/arm64/boot/dts/broadcom/bcm2837-rpi-3-b.dtb \
-nographic -monitor null -serial null -serial stdio
This is with arm64:defconfig. The root file system was generated using
buildroot.
NB that this error likely arises from an erratum in the
BCM2835 datasheet where the TX and RX bits were swapped
in the AU_MU_IER_REG description (but correct for IIR):
https://elinux.org/BCM2835_datasheet_errata#p12
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 1529355846-25102-1-git-send-email-linux@roeck-us.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: added NB about datasheet]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Frontends should have an interface to setup the handler of a backend change.
The interface will be used in the next commits
Signed-off-by: Anton Nefedov <anton.nefedov@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1499342940-56739-3-git-send-email-anton.nefedov@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
No need to keep explicit_fe_open around if it affects only a
qemu_chr_fe_set_handlers(). Use an additional argument instead.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-24-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In most cases, front ends do not care about the side effect of
CharBackend, so we can simply skip the checks and call the qemu_chr_fe
functions even without associated CharDriver.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-20-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This also switches from qemu_chr_add_handlers() to
qemu_chr_fe_set_handlers(). Note that qemu_chr_fe_set_handlers() now
takes the focus when fe_open (qemu_chr_add_handlers() did take the
focus)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-16-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
qemu_chr_accept_input() and qemu_chr_disconnect() are only used by
frontend, so use qemu_chr_fe prefix.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-14-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Store the property in a CharBackend instead of CharDriverState*. This
also replace systematically chr by chr.chr to access the
CharDriverState*. The following patches will replace it with calls to
qemu_chr_fe CharBackend functions.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-12-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The qemu_chr_fe_write method will return -1 on EAGAIN if the
chardev backend write would block. Almost no callers of the
qemu_chr_fe_write() method check the return value, instead
blindly assuming data was successfully sent. In most cases
this will lead to silent data loss on interactive consoles,
but in some cases (eg RNG EGD) it'll just cause corruption
of the protocol being spoken.
We unfortunately can't fix the virtio-console code, due to
a bug in the Linux guest drivers, which would cause the
entire Linux kernel to hang if we delay processing of the
incoming data in any way. Fixing this requires first fixing
the guest driver to not hold spinlocks while writing to the
hvc device backend.
Fixes bug: https://bugs.launchpad.net/qemu/+bug/1586756
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1473170165-540-4-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
At present only the core UART functions (data path for tx/rx) are
implemented, which is enough for UEFI to boot. The following
features/registers are unimplemented:
* Line/modem control
* Scratch register
* Extra control
* Baudrate
* SPI interfaces
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1457467526-8840-3-git-send-email-Andrew.Baumann@microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
