Make hw/vfio configurable and add new CONFIG_VFIO_* to the
default-configs/s390x*-softmmu.mak. This allow a finer-grain
selection of the various VFIO backends.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-28-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Create separate variables for these components, they are
used in many boards but not all. This allows finer-grain
selection of the included code with default-configs/*.mak.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the new configs to default-configs/tricore-sofmmu.mak.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-26-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the new configs to default-configs/or1k-sofmmu.mak.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-25-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CONFIG_MOXIE added for moxiesim board.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-24-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the new configs to default-configs/hppa-sofmmu.mak.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20190202072456.6468-23-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the new configs to default-configs/cris-sofmmu.mak.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-22-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the new configs to default-configs/alpha-sofmmu.mak.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20190202072456.6468-21-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the new configs to default-configs/sparc64-sofmmu.mak.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-20-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the new configs to default-configs/riscv*-sofmmu.mak.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-19-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CONFIG_NIOS2_10M50 added for 10m50 dev board.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-18-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the new CONFIG_* values to default-config/xtensa*-softmmu.mak.
Signed-off-by: Ákos Kovács <akoskovacs@gmx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Message-Id: <20190202072456.6468-17-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CONFIG_LM32 and CONFIG_MILKYMIST added for lm32 and milkmyst build.
Signed-off-by: Ákos Kovács <akoskovacs@gmx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-16-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CONFIG_LEON3 added to default-configs/sparc-softmmu.mak.
Signed-off-by: Ákos Kovács <akoskovacs@gmx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-15-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make hw/s390x configurable and add new CONFIG_* to the
default-configs/s390x*-softmmu.mak. This will be used to
enable/disable vfio-ccw.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-14-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make hw/sh4 configurable and add new CONFIG_* to the
default-configs/sh4*-softmmu.mak.
Signed-off-by: Ákos Kovács <akoskovacs@gmx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-13-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CONFIG_PPC405, CONFIG_PPC440, CONFIG_MAC_OLDWORLD, CONFIG_MAX_NEWWORLD
and CONFIG_VIRTEX configuration options created for
default-configs/ppc*-softmmu.mak.
Signed-off-by: Ákos Kovács <akoskovacs@gmx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-12-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the new configs to default-configs/mips*-sofmmu.mak.
Signed-off-by: Ákos Kovács <akoskovacs@gmx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-11-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CONFIG_PETALOGIX_* and CONFIG_XLNX_* configs added to
default-configs/microblaze-softmmu.mak and
default-configs/microblazeel-softmmu.mak.
Signed-off-by: Ákos Kovács <akoskovacs@gmx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-10-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CONFIG_AN5206, CONFIG_MCF5206 and CONFIG_MCF5208 make
variables created for m68k boards, and added to
default-configs/m86k-softmmu.mak.
Signed-off-by: Ákos Kovács <akoskovacs@gmx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-9-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make ARM virt code configurable and the new CONFIG_ARM_VIRT
definitions added to the default-configs/arm-softmmu.mak.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-8-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CONFIG_PIIX and CONFIG_Q35 created for the pc board object files. These
are enabled automatically at default-configs/i386-softmmu.mak and
default-configs/x86_64-softmmu.mak
Signed-off-by: Ákos Kovács <akoskovacs@gmx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-7-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Do not link it unconditionally into all binaries.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-6-yang.zhong@intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Change the CONFIGs for PCI EXPRESS and make module name more
clear for code files.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-5-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of wrapping the entire Makefile.objs with an ifeq/endif, just
include the directory only for Linux.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-4-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is not needed on ARM, and brings in ISA bus code which is otherwise not
necessary.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-3-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Whenever the allocation length of a SCSI request is shorter than the size of the
VPD page list, page_idx is used blindly to index into r->buf. Even though
the stores in the insertion sort are protected against overflows, the same is not
true of the reads and the final store of 0xb0.
This basically does the same thing as commit 57dbb58d80 ("scsi-generic: avoid
out-of-bounds access to VPD page list", 2018-11-06), except that here the
allocation length can be chosen by the guest. Note that according to the SCSI
standard, the contents of the PAGE LENGTH field are not altered based
on the allocation length.
The code was introduced by commit 6c219fc8a1 ("scsi-generic: keep VPD
page list sorted", 2018-11-06) but the overflow was already possible before.
Reported-by: Kevin Wolf <kwolf@redhat.com>
Fixes: a71c775b24
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since linux commit: cf8fa920cb42 ("i386: handle an initrd in highmem (version 2)")
linux has supported initrd up to 4 GB, but the header field
ramdisk_max is still set to 2 GB to avoid "possible bootloader bugs".
When use '-kernel vmlinux -initrd initrd.cgz' to launch a VM,
the firmware(it could be linuxboot_dma.bin) helps to read initrd
contents into guest memory(below ramdisk_max) and jump to kernel.
that's similar with what bootloader does, like grub.
In addition, initrd_max is uint32_t simply because QEMU doesn't support
the 64-bit boot protocol (specifically the ext_ramdisk_image field).
Therefore here just limit initrd_max to UINT32_MAX simply as well to
allow initrd to be loaded below 4 GB.
NOTE: it's possible that linux protocol within [0x208, 0x20c]
supports up to 4 GB initrd as well.
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Eduardo Habkost <ehabkost@redhat.com>
CC: "Michael S. Tsirkin" <mst@redhat.com>
CC: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
it's from v4.20-rc5.
CC: Stefano Garzarella <sgarzare@redhat.com>
CC: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Don't expect read(2) can always read as many as it's told.
CC: Richard Henderson <richard.henderson@linaro.org>
CC: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to avoid migration issues, we enable PVH only for
machine type >= 4.0
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use pvh.bin option rom when we are booting an uncompressed
kernel using the x86/HVM direct boot ABI.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Based-on: <1547554687-12687-1-git-send-email-liam.merwick@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When initrd is specified, load and expose it to the guest firmware
through fw_cfg. The firmware will fill the hvm_start_info for the
kernel.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Based-on: <1545422632-24444-5-git-send-email-liam.merwick@oracle.com>
Signed-off-by: Liam Merwick <Liam.Merwick@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These changes (along with corresponding Linux kernel and qboot changes)
enable a guest to be booted using the x86/HVM direct boot ABI.
This commit adds a load_elfboot() routine to pass the size and
location of the kernel entry point to qboot (which will fill in
the start_info struct information needed to to boot the guest).
Having loaded the ELF binary, load_linux() will run qboot
which continues the boot.
The address for the kernel entry point is read from an ELF Note
in the uncompressed kernel binary by a helper routine passed
to load_elf().
Co-developed-by: George Kennedy <George.Kennedy@oracle.com>
Signed-off-by: George Kennedy <George.Kennedy@oracle.com>
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds an optional function pointer, 'elf_note_fn', to
load_elf() which causes load_elf() to additionally parse any
ELF program headers of type PT_NOTE and check to see if the ELF
Note is of the type specified by the 'translate_opaque' arg.
If a matching ELF Note is found then the specfied function pointer
is called to process the ELF note.
Passing a NULL function pointer results in ELF Notes being skipped.
The first consumer of this functionality is the PVHboot support
which needs to read the XEN_ELFNOTE_PHYS32_ENTRY ELF Note while
loading the uncompressed kernel binary in order to discover the
boot entry address for the x86/HVM direct boot ABI.
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- fix CPU wakeup on runstall changes; expose runstall as an IRQ line;
- place mini-bootloader at the BSP reset vector;
- expose CPU core frequency in XTFPGA board FPGA register;
- rearrange access to external interrupts of xtensa cores;
- add MX interrupt distributor and use it on SMP XTFPGA boards;
- add test_mmuhifi_c3 xtensa core variant;
- raise number of CPUs that can be instantiated on XTFPGA boards.
-----BEGIN PGP SIGNATURE-----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=8D60
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/xtensa/tags/20190204-xtensa' into staging
target/xtensa: SMP updates and various fixes
- fix CPU wakeup on runstall changes; expose runstall as an IRQ line;
- place mini-bootloader at the BSP reset vector;
- expose CPU core frequency in XTFPGA board FPGA register;
- rearrange access to external interrupts of xtensa cores;
- add MX interrupt distributor and use it on SMP XTFPGA boards;
- add test_mmuhifi_c3 xtensa core variant;
- raise number of CPUs that can be instantiated on XTFPGA boards.
# gpg: Signature made Mon 04 Feb 2019 18:59:32 GMT
# gpg: using RSA key 2B67854B98E5327DCDEB17D851F9CC91F83FA044
# gpg: issuer "jcmvbkbc@gmail.com"
# gpg: Good signature from "Max Filippov <filippov@cadence.com>" [unknown]
# gpg: aka "Max Filippov <max.filippov@cogentembedded.com>" [full]
# gpg: aka "Max Filippov <jcmvbkbc@gmail.com>" [full]
# Primary key fingerprint: 2B67 854B 98E5 327D CDEB 17D8 51F9 CC91 F83F A044
* remotes/xtensa/tags/20190204-xtensa:
hw/xtensa: xtfpga: raise CPU number limit
target/xtensa: add test_mmuhifi_c3 core
hw/xtensa: xtfpga: use MX PIC for SMP
target/xtensa: add MX interrupt controller
target/xtensa: expose core runstall as an IRQ line
target/xtensa: rearrange access to external interrupts
target/xtensa: drop function xtensa_timer_irq
target/xtensa: fix access to the INTERRUPT SR
hw/xtensa: xtfpga: use core frequency
hw/xtensa: xtfpga: fix bootloader placement in SMP
target/xtensa: add qemu_cpu_kick to xtensa_runstall
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some frontend drivers will handle dynamic resizing of PV disks, so set up
the BlockDevOps resize_cb() method during xen_block_realize() to allow
this to be done.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
There is a flaw in the xen-bus state model. To allow a frontend to re-
connect the backend state of an online XenDevice is transitioned from
Closed to InitWait, but this is currently done unilaterally which is
incorrect. The backend state should remain Closed until the frontend state
transitions to Initialising.
This patch removes the automatic backend state transition from
xen_device_backend_state_changed() and, instead, adds an extra check in
xen_device_frontend_state_changed() to determine whether a frontend is
trying to re-connect to a previously Closed XenDevice. Only if this is
found to be the case is the backend state transitioned from Closed to
InitWait. Note that this transition will be common amongst all XenDevice
classes and hence xen_device_frontend_state_changed() returns immediately
afterwards without calling into the XenDeviceClass frontend_changed()
method.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
These files don't use anything from m48t59.h, so no need to include
this header here.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
reg->phys_hi and assigned->phys_hi are big endian but we do an extra
byteswap anyway when copying reg->phys_hi to assigned->phys_hi.
To make things slightly more messy, we also add a relocatable bit (b_n())
although in the right endianness.
This fixes endianness of assigned->phys_hi.
This is unlikely to produce any visible difference though as we should end up
there only in the case of PCI hotplug and even then I am not sure if
(d->io_regions[i].addr == PCI_BAR_UNMAPPED) == true.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The cirrus VGA card has been enabled in the PPC builds with
commit 29f9cef39e ("ppc: Include vga cirrus card into
the compiling process") last year. It also works on the pseries
machine, even SLOF contains support for this card, so we can
also support this for the "-vga" parameter here.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_load_rtas() handles now RTAS address and size information in the FDT
so drop them from spapr_build_fdt().
While we are here, fix a small typo.
Fixes: 3f5dabceba "pseries: Consolidate construction of /rtas device tree node"
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Currently, it is not possible to build a QEMU binary without the
ppc405_uc.c file, even if you do not want to have the embedded machines
in the binary. This is bad since it's quite a bit of code and this code
pulls in some more dependencies (e.g. via the usage of serial_mm_init())
which would not be needed otherwise - especially with the upcoming
Kconfig-style configuration system for QEMU.
The only functions from this file which are really always required for
linking are the ppc40x_*reset() functions, so move these functions to
ppc.c, close to the ppc40x_set_irq() function that calls them. Now we
can flag ppc405_uc.c and ppc4xx_devs.c with the CONFIG_PPC4XX config
switch, too.
And while we're at it, replace the printf()s in these ppc40x_*reset()
functions with proper calls to qemu_log_mask().
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Next step is to remove them from under the PowerPCCPU
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Include the interrupt presenter under the machine_data as we plan to
remove it from under PowerPCCPU
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It provides a mean to retrieve the XiveTCTX of a CPU. This will become
necessary with future changes which move the interrupt presenter
object pointers under the PowerPCCPU machine_data.
The PowerNV machine has an extra requirement on TIMA accesses that
this new method addresses. The machine can perform indirect loads and
stores on the TIMA on behalf of another CPU. The PIR being defined in
the controller registers, we need a way to peek in the controller
model to find the PIR value.
The XiveTCTX is moved above the XiveRouter definition to avoid forward
typedef declarations.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
While looking at the s390x implementation, looks like spapr has a
similar BUG when building the topology.
The primary bus number corresponds always to the bus number of the
bus the bridge is attached to.
Right now, if we have two bridges attached to the same bus (e.g. root
bus) this is however not the case. The first bridge will have primary
bus 0, the second bridge primary bus 1, which is wrong. Fix the assignment.
While at it, drop setting the PCI_SUBORDINATE_BUS temporarily to 0xff.
Setting it temporarily to that value (as discussed e.g. in [1]), is
only relevant for a running system that probes the buses. The value is
effectively unused for us just doing a DFS.
[1] http://www.science.unitn.it/~fiorella/guidelinux/tlk/node76.html
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Machine types 3.0 and older only know about the legacy XICS backend.
Make it clear by erroring out if the user tries to set ic-mode on
such machines.
Signed-off-by: Greg Kurz <groug@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In hw/scsi/spapr_vio.c we declare that the controller supports multiple
buses by specifying "max_channel = 7" there. So in the code that fixes
up the device tree nodes, we must encode the channel number (a.k.a. bus
number in the "Logical unit addressing format" table of SAM5) into the
64-bit LUN, too.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1663160
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
