Each CS has its own Read Timing Compensation Register on newer SoCs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-13-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2600 control register sneakily changed the meaning of bit 4
without anyone noticing. It no longer controls the 1MHz vs APB clock
select, and instead always runs at 1MHz.
The AST2500 was always 1MHz too, but it retained bit 4, making it read
only. We can model both using the same fixed 1MHz calculation.
Fixes: 6b2b2a703c ("hw: wdt_aspeed: Add AST2600 support")
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-10-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The I2C controller of the Aspeed AST2500 and AST2600 SoCs supports DMA
transfers to and from DRAM.
A pair of registers defines the buffer address and the length of the
DMA transfer. The address should be aligned on 4 bytes and the maximum
length should not exceed 4K. The receive or transmit DMA transfer can
then be initiated with specific bits in the Command/Status register of
the controller.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently, we link the DRAM memory region to the FMC model (for DMAs)
through a property alias at the SoC level. The I2C model will need a
similar region for DMA support, add a DRAM region property at the SoC
level for both model to use.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SRAM must be enabled before using the Buffer Pool mode or the DMA
mode. This is not required on other SoCs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed I2C controller can operate in different transfer modes :
- Byte Buffer mode, using a dedicated register to transfer a
byte. This is what the model supports today.
- Pool Buffer mode, using an internal SRAM to transfer multiple
bytes in the same command sequence.
Each SoC has different SRAM characteristics. On the AST2400, 2048
bytes of SRAM are available at offset 0x800 of the controller AHB
window. The pool buffer can be configured from 1 to 256 bytes per bus.
On the AST2500, the SRAM is at offset 0x200 and the pool buffer is of
16 bytes per bus.
On the AST2600, the SRAM is at offset 0xC00 and the pool buffer is of
32 bytes per bus. It can be splitted in two for TX and RX but the
current model does not add support for it as it it unused by known
drivers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Virtio spec 1.1 (and earlier), 5.2.5.2 Driver Requirements: Device
Initialization:
"Devices SHOULD always offer VIRTIO_BLK_F_FLUSH, and MUST offer it if
they offer VIRTIO_BLK_F_CONFIG_WCE"
Currently F_CONFIG_WCE and F_WCE are not connected to each other.
Qemu will advertise F_CONFIG_WCE if config-wce argument is
set for virtio-blk device. And F_WCE is advertised only if
underlying block backend actually has it's caching enabled.
Fix this by advertising F_WCE if F_CONFIG_WCE is also advertised.
To preserve backwards compatibility with newer machine types make this
behaviour governed by "x-enable-wce-if-config-wce" virtio-blk-device
property and introduce hw_compat_4_2 with new property being off by
default for all machine types <= 4.2 (but don't introduce 4.3
machine type itself yet).
Signed-off-by: Evgeny Yakovlev <wrfsh@yandex-team.ru>
Message-Id: <1572978137-189218-1-git-send-email-wrfsh@yandex-team.ru>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The property doesn't make much sense for a vhost-user device.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20191116112016.14872-1-marcandre.lureau@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Here's the first 4.2 hard freeze pull request from me. This has:
* A fix for some testcases that cause errors on older host kernels
(e.g. RHEL7), with our new default configuration of VSMT mode
* Changes to make VFIO devices interact properly with change of irq
chip caused by PAPR feature negotiation. This is more involved
than I would like, but it's a problem in real use cases and I
can't see an easier way to handle it.
* Fix an error with ms6522 counters for the g3beige machine
* Fix a coverity warning
-----BEGIN PGP SIGNATURE-----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=GHGC
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.2-20191126' into staging
ppc patch queue for 2019-11-26
Here's the first 4.2 hard freeze pull request from me. This has:
* A fix for some testcases that cause errors on older host kernels
(e.g. RHEL7), with our new default configuration of VSMT mode
* Changes to make VFIO devices interact properly with change of irq
chip caused by PAPR feature negotiation. This is more involved
than I would like, but it's a problem in real use cases and I
can't see an easier way to handle it.
* Fix an error with ms6522 counters for the g3beige machine
* Fix a coverity warning
# gpg: Signature made Tue 26 Nov 2019 05:52:16 GMT
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.2-20191126:
ppc/spapr_events: fix potential NULL pointer dereference in rtas_event_log_dequeue
mos6522: update counters when timer interrupts are off
spapr: Work around spurious warnings from vfio INTx initialization
spapr: Handle irq backend changes with VFIO PCI devices
vfio/pci: Respond to KVM irqchip change notifier
vfio/pci: Split vfio_intx_update()
kvm: Introduce KVM irqchip change notifier
pseries: fix migration-test and pxe-test
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the CRP as unimplemented thus avoiding bus errors when
guests access these registers.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20191115154734.26449-2-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Awareness of an in kernel irqchip is usually local to the machine and its
top-level interrupt controller. However, in a few cases other things need
to know about it. In particular vfio devices need this in order to
accelerate interrupt delivery.
If interrupt routing is changed, such devices may need to readjust their
connection to the KVM irqchip. pci_bus_fire_intx_routing_notifier() exists
to do just this.
However, for the pseries machine type we have a situation where the routing
remains constant but the top-level irq chip itself is changed. This occurs
because of PAPR feature negotiation which allows the guest to decide
between the older XICS and newer XIVE irq chip models (both of which are
paravirtualized).
To allow devices like vfio to adjust to this change, introduce a new
notifier for the purpose kvm_irqchip_change_notify().
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
This patch adds an optional function pointer, "sym_cb", to
riscv_load_kernel() which provides the possibility to access the symbol
table during kernel loading.
The pointer is ignored, if supplied with Image or uImage file.
The Spike board requires the access to locate the HTIF symbols.
Fixes: 0ac24d56c5 ("hw/riscv: Split out the boot functions")
Buglink: https://bugs.launchpad.net/qemu/+bug/1835827
Signed-off-by: Siwei Zhuang <siwei.zhuang@data61.csiro.au>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Attempting to migrate a VM using the microvm machine class results in the source
QEMU aborting with the following message/backtrace:
target/i386/machine.c:955:tsc_khz_needed: Object 0x555556608fa0 is not an
instance of type generic-pc-machine
abort()
object_class_dynamic_cast_assert()
vmstate_save_state_v()
vmstate_save_state()
vmstate_save()
qemu_savevm_state_complete_precopy()
migration_thread()
migration_thread()
migration_thread()
qemu_thread_start()
start_thread()
clone()
The access to the machine class returned by MACHINE_GET_CLASS() in
tsc_khz_needed() is crashing as it is trying to dereference a different
type of machine class object (TYPE_PC_MACHINE) to that of this microVM.
This can be resolved by extending the changes in the following commit
f0bb276bf8 ("hw/i386: split PCMachineState deriving X86MachineState from it")
and moving the save_tsc_khz field in PCMachineClass to X86MachineClass.
Fixes: f0bb276bf8 ("hw/i386: split PCMachineState deriving X86MachineState from it")
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Message-Id: <1574075605-25215-1-git-send-email-liam.merwick@oracle.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Qemu as server currently won't accept export names larger than 256
bytes, nor create dirty bitmap names longer than 1023 bytes, so most
uses of qemu as client or server have no reason to get anywhere near
the NBD spec maximum of a 4k limit per string.
However, we weren't actually enforcing things, ignoring when the
remote side violates the protocol on input, and also having several
code paths where we send oversize strings on output (for example,
qemu-nbd --description could easily send more than 4k). Tighten
things up as follows:
client:
- Perform bounds check on export name and dirty bitmap request prior
to handing it to server
- Validate that copied server replies are not too long (ignoring
NBD_INFO_* replies that are not copied is not too bad)
server:
- Perform bounds check on export name and description prior to
advertising it to client
- Reject client name or metadata query that is too long
- Adjust things to allow full 4k name limit rather than previous
256 byte limit
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20191114024635.11363-4-eblake@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
We document that for qcow2 persistent bitmaps, the name cannot exceed
1023 bytes. It is inconsistent if transient bitmaps do not have to
abide by the same limit, and it is unlikely that any existing client
even cares about using bitmap names this long. It's time to codify
that ALL bitmaps managed by qemu (whether persistent in qcow2 or not)
have a documented maximum length.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20191114024635.11363-3-eblake@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
As long as we limit NBD names to 256 bytes (the bare minimum permitted
by the standard), stack-allocation works for parsing a name received
from the client. But as mentioned in a comment, we eventually want to
permit up to the 4k maximum of the NBD standard, which is too large
for stack allocation; so switch everything in the server to use heap
allocation. For now, there is no change in actually supported name
length.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20191114024635.11363-2-eblake@redhat.com>
[eblake: fix uninit variable compile failure]
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
SpaprInterruptControllerClass and PnvChipClass have an intc_create() method
that calls the appropriate routine, ie. icp_create() or xive_tctx_create(),
to establish the link between the VCPU and the presenter component of the
interrupt controller during realize.
There aren't any symmetrical call to be called when the VCPU gets unrealized
though. It is assumed that object_unparent() is the only thing to do.
This is questionable because the parenting logic around the CPU and
presenter objects is really an implementation detail of the interrupt
controller. It shouldn't be open-coded in the machine code.
Fix this by adding an intc_destroy() method that undoes what was done in
intc_create(). Also NULLify the presenter pointers to avoid having
stale pointers around. This will allow to reliably check if a vCPU has
a valid presenter.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157192724208.3146912.7254684777515287626.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
This is a very simple versioning API which allows the plugin
infrastructure to check the API a plugin was built against. We also
expose a min/cur API version to the plugin via the info block in case
it wants to avoid using old deprecated APIs in the future.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Robert Foley <robert.foley@linaro.org>
The boot.c code usually puts the CPU into NS mode directly when it is
booting a kernel. Since fc1120a7f5 this has included a
requirement to set NSACR to give NS state access to the FPU; we fixed
that for the usual code path in ece628fcf6. However, it is also
possible for a board model to request an alternative mode of booting,
where its 'board_setup' code hook runs in Secure state and is
responsible for doing the S->NS transition after it has done whatever
work it must do in Secure state. In this situation the board_setup
code now also needs to update NSACR.
This affects all boards which set info->secure_board_setup, which is
currently the 'raspi' and 'highbank' families. They both use the
common arm_write_secure_board_setup_dummy_smc().
Set the NSACR CP11 and CP10 bits in the code written by that
function, to allow FPU access in Non-Secure state when using dummy
SMC setup routine. Otherwise an AArch32 kernel booted on the
highbank or raspi boards will UNDEF as soon as it tries to use the
FPU.
Update the comment describing secure_board_setup to note the new
requirements on users of it.
This fixes a kernel panic when booting raspbian on raspi2.
Successfully tested with:
2017-01-11-raspbian-jessie-lite.img
2018-11-13-raspbian-stretch-lite.img
2019-07-10-raspbian-buster-lite.img
Fixes: fc1120a7f5
Signed-off-by: Clement Deschamps <clement.deschamps@greensocs.com>
Tested-by: Laurent Bonnans <laurent.bonnans@here.com>
Message-id: 20191104151137.81931-1-clement.deschamps@greensocs.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: updated comment to boot.h to note new requirement on
users of secure_board_setup; edited/rewrote commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All targets have now migrated away from the old unassigned_access
hook to the new do_transaction_failed hook. This means we can remove
the core-code infrastructure for that hook and the code that calls it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20191108173732.11816-1-peter.maydell@linaro.org
Now all the users of ptimers have converted to the transaction-based
API, we can remove ptimer_init_with_bh() and all the code paths
that are used only by bottom-half based ptimers, and tidy up the
documentation comments to consider the transaction-based API the
only possibility.
The code changes result from:
* s->bh no longer exists
* s->callback is now always non-NULL
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191025142411.17085-1-peter.maydell@linaro.org
PIIX southbridge is also used by the Malta MIPS machine.
Split the PIIX3 southbridge from i440FX northbridge.
-----BEGIN PGP SIGNATURE-----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=cQ/y
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/philmd-gitlab/tags/mips-next-20191105' into staging
The i440FX northbridge is only used by the PC machine, while the
PIIX southbridge is also used by the Malta MIPS machine.
Split the PIIX3 southbridge from i440FX northbridge.
# gpg: Signature made Tue 05 Nov 2019 22:48:12 GMT
# gpg: using RSA key 89C1E78F601EE86C867495CBA2A3FD6EDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (Phil) <philmd@redhat.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 89C1 E78F 601E E86C 8674 95CB A2A3 FD6E DEAD C0DE
* remotes/philmd-gitlab/tags/mips-next-20191105: (21 commits)
hw/pci-host/i440fx: Remove the last PIIX3 traces
hw/pci-host: Rename incorrectly named 'piix' as 'i440fx'
hw/pci-host/piix: Extract PIIX3 functions to hw/isa/piix3.c
hw/pci-host/piix: Fix code style issues
hw/pci-host/piix: Move i440FX declarations to hw/pci-host/i440fx.h
hw/pci-host/piix: Define and use the PIIX IRQ Route Control Registers
hw/pci-host/piix: Move RCR_IOPORT register definition
hw/pci-host/piix: Extract piix3_create()
hw/i386: Remove obsolete LoadStateHandler::load_state_old handlers
hw/isa/piix4: Move piix4_create() to hw/isa/piix4.c
hw/mips/mips_malta: Extract the PIIX4 creation code as piix4_create()
hw/mips/mips_malta: Create IDE hard drive array dynamically
piix4: Add a MC146818 RTC Controller as specified in datasheet
piix4: Add an i8254 PIT Controller as specified in datasheet
piix4: Add an i8257 DMA Controller as specified in datasheet
piix4: Rename PIIX4 object to piix4-isa
Revert "irq: introduce qemu_irq_proxy()"
piix4: Add an i8259 Interrupt Controller as specified in datasheet
piix4: Add the Reset Control Register
MAINTAINERS: Keep PIIX4 South Bridge separate from PC Chipsets
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
'the' has a tendency to double up; squash them back down.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191104185202.102504-1-dgilbert@redhat.com>
[lv: removed disas/libvixl/vixl/invalset.h change]
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Host notifiers are used in several cases:
1. Traditional ioeventfd where virtqueue notifications are handled in
the main loop thread.
2. IOThreads (aio_handle_output) where virtqueue notifications are
handled in an IOThread AioContext.
3. vhost where virtqueue notifications are handled by kernel vhost or
a vhost-user device backend.
Most virtqueue notifications from the guest use the ioeventfd mechanism,
but there are corner cases where QEMU code calls virtio_queue_notify().
This currently honors the host notifier for the IOThreads
aio_handle_output case, but not for the vhost case. The result is that
vhost does not receive virtqueue notifications from QEMU when
virtio_queue_notify() is called.
This patch extends virtio_queue_notify() to set the host notifier
whenever it is enabled instead of calling the vq->(aio_)handle_output()
function directly. We track the host notifier state for each virtqueue
separately since some devices may use it only for certain virtqueues.
This fixes the vhost case although it does add a trip through the
eventfd for the traditional ioeventfd case. I don't think it's worth
adding a fast path for the traditional ioeventfd case because calling
virtio_queue_notify() is rare when ioeventfd is enabled.
Reported-by: Felipe Franciosi <felipe@nutanix.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20191105140946.165584-1-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The PIIX3 is not tied to the i440FX and can even be used without it.
Move its creation to the machine code (pc_piix.c).
We have now removed the last trace of southbridge code in the i440FX
northbridge.
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Move all the PIIX3 functions to a new file: hw/isa/piix3.c.
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The hw/pci-host/piix.c contains a mix of PIIX3 and i440FX chipsets
functions. To be able to split it, we need to export some
declarations first.
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The IRQ Route Control registers definitions belong to the PIIX
chipset. We were only defining the 'A' register. Define the other
B, C and D registers, and use them.
Acked-by: Paul Durrant <paul@xen.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The RCR_IOPORT register belongs to the PIIX chipset.
Move the definition to "piix.h", and prepend the PIIX prefix.
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Now that we properly refactored the piix4_create() function, let's
move it to hw/isa/piix4.c where it belongs, so it can be reused
on other places.
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Remove mc146818rtc instanciated in malta board, to not have it twice.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20171216090228.28505-13-hpoussin@reactos.org>
[PMD: rebased, set RTC base_year to 2000]
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Other piix4 parts are already named piix4-ide and piix4-usb-uhci.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20171216090228.28505-15-hpoussin@reactos.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Esteban Bosse <estebanbosse@gmail.com>
[PMD: rebased]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This function isn't used anymore.
This reverts commit 22ec3283ef.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Esteban Bosse <estebanbosse@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Add ISA irqs as piix4 gpio in, and CPU interrupt request as piix4 gpio out.
Remove i8259 instanciated in malta board, to not have it twice.
We can also remove the now unused piix4_init() function.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20171216090228.28505-8-hpoussin@reactos.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
[PMD: rebased, updated includes, use ISA_NUM_IRQS in for loop]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Make both bdrv_mark_request_serialising() and
bdrv_wait_serialising_requests() public so they can be used from block
drivers.
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20191101152510.11719-2-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Fix the offset of the NSSRS field the CAP register.
From NVME 1.4, section 3 ("Controller Registers"), subsection 3.1.1
("Offset 0h: CAP – Controller Capabilities") CAP_NSSRS_SHIFT is bit 36,
not 33.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reported-by: Javier Gonzalez <javier.gonz@samsung.com>
Message-id: 20191023073315.446534-1-its@irrelevant.dk
Reviewed-by: John Snow <jsnow@redhat.com>
[mreitz: Added John's note on the location in the specification where
this information can be found]
Signed-off-by: Max Reitz <mreitz@redhat.com>
Introduce cpu properties to give fine control over SVE vector lengths.
We introduce a property for each valid length up to the current
maximum supported, which is 2048-bits. The properties are named, e.g.
sve128, sve256, sve384, sve512, ..., where the number is the number of
bits. See the updates to docs/arm-cpu-features.rst for a description
of the semantics and for example uses.
Note, as sve-max-vq is still present and we'd like to be able to
support qmp_query_cpu_model_expansion with guests launched with e.g.
-cpu max,sve-max-vq=8 on their command lines, then we do allow
sve-max-vq and sve<N> properties to be provided at the same time, but
this is not recommended, and is why sve-max-vq is not mentioned in the
document. If sve-max-vq is provided then it enables all lengths smaller
than and including the max and disables all lengths larger. It also has
the side-effect that no larger lengths may be enabled and that the max
itself cannot be disabled. Smaller non-power-of-two lengths may,
however, be disabled, e.g. -cpu max,sve-max-vq=4,sve384=off provides a
guest the vector lengths 128, 256, and 512 bits.
This patch has been co-authored with Richard Henderson, who reworked
the target/arm/cpu64.c changes in order to push all the validation and
auto-enabling/disabling steps into the finalizer, resulting in a nice
LOC reduction.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Reviewed-by: Beata Michalska <beata.michalska@linaro.org>
Message-id: 20191031142734.8590-5-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Using fw_cfg, supply logical CHS values directly from QEMU to the BIOS.
Non-standard logical geometries break under QEMU.
A virtual disk which contains an operating system which depends on
logical geometries (consistent values being reported from BIOS INT13
AH=08) will most likely break under QEMU/SeaBIOS if it has non-standard
logical geometries - for example 56 SPT (sectors per track).
No matter what QEMU will report - SeaBIOS, for large enough disks - will
use LBA translation, which will report 63 SPT instead.
In addition we cannot force SeaBIOS to rely on physical geometries at
all. A virtio-blk-pci virtual disk with 255 phyiscal heads cannot
report more than 16 physical heads when moved to an IDE controller,
since the ATA spec allows a maximum of 16 heads - this is an artifact of
virtualization.
By supplying the logical geometries directly we are able to support such
"exotic" disks.
We serialize this information in a similar way to the "bootorder"
interface.
The new fw_cfg entry is "bios-geometry".
Reviewed-by: Karl Heubaum <karl.heubaum@oracle.com>
Reviewed-by: Arbel Moshe <arbel.moshe@oracle.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Sam Eiderman <shmuel.eiderman@oracle.com>
Signed-off-by: Sam Eiderman <sameid@google.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
We will need to add LCHS removal logic to scsi-hd's unrealize() in the
next commit.
Reviewed-by: Karl Heubaum <karl.heubaum@oracle.com>
Reviewed-by: Arbel Moshe <arbel.moshe@oracle.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Sam Eiderman <shmuel.eiderman@oracle.com>
Signed-off-by: Sam Eiderman <sameid@google.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Add an interface to provide direct logical CHS values for boot devices.
We will use this interface in the next commits.
Reviewed-by: Karl Heubaum <karl.heubaum@oracle.com>
Reviewed-by: Arbel Moshe <arbel.moshe@oracle.com>
Signed-off-by: Sam Eiderman <shmuel.eiderman@oracle.com>
Signed-off-by: Sam Eiderman <sameid@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Add logical geometry variables to BlockConf.
A user can now supply "lcyls", "lheads" & "lsecs" for any HD device
that supports CHS ("cyls", "heads", "secs").
These devices include:
* ide-hd
* scsi-hd
* virtio-blk-pci
In future commits we will use the provided LCHS and pass it to the BIOS
through fw_cfg to be supplied using INT13 routines.
Reviewed-by: Karl Heubaum <karl.heubaum@oracle.com>
Reviewed-by: Arbel Moshe <arbel.moshe@oracle.com>
Signed-off-by: Sam Eiderman <shmuel.eiderman@oracle.com>
Signed-off-by: Sam Eiderman <sameid@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Fixing tabbing in block related macros.
Signed-off-by: Sam Eiderman <shmuel.eiderman@oracle.com>
Signed-off-by: Sam Eiderman <sameid@google.com>
Reviewed-by: Karl Heubaum <karl.heubaum@oracle.com>
Reviewed-by: Arbel Moshe <arbel.moshe@oracle.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
- use --enable-plugins @ configure
- low impact introspection (-plugin empty.so to measure overhead)
- plugins cannot alter guest state
- example plugins included in source tree (tests/plugins)
- -d plugin to enable plugin output in logs
- check-tcg runs extra tests when plugins enabled
- documentation in docs/devel/plugins.rst
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAl23BZMACgkQ+9DbCVqe
KkRPegf/QHygZ4ER2jOaWEookxiOEcik+dzQKVGNqLNXeMLvo5fGjGVpFoFxSgfv
ZvCAL4xbW44zsYlVfh59tfn4Tu9qK7s7/qM3WXpHsmuvEuhoWef0Lt2jSe+D46Rs
KeG/aX+rHLUR8rr9eCgE+1/MQmxPUj3VUonkUpNkk2ebBbSNoLSOudB4DD9Vcyl7
Pya1kPvA6W9bwI20ZSWihE7flg13o62Pp+LgAFLrsfxXOxOMkPrU8Pp+B0Dvr+hL
5Oh0clZLhiRi75x+KVGZ90TVsoftdjYoOWGMOudS/+NNmqKT1NTLm0K1WJYyRMQ1
V0ne4/OcGNq7x8gcOx/xs09ADu5/VA==
=UXR/
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-tcg-plugins-281019-4' into staging
TCG Plugins initial implementation
- use --enable-plugins @ configure
- low impact introspection (-plugin empty.so to measure overhead)
- plugins cannot alter guest state
- example plugins included in source tree (tests/plugins)
- -d plugin to enable plugin output in logs
- check-tcg runs extra tests when plugins enabled
- documentation in docs/devel/plugins.rst
# gpg: Signature made Mon 28 Oct 2019 15:13:23 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-tcg-plugins-281019-4: (57 commits)
travis.yml: enable linux-gcc-debug-tcg cache
MAINTAINERS: add me for the TCG plugins code
scripts/checkpatch.pl: don't complain about (foo, /* empty */)
.travis.yml: add --enable-plugins tests
include/exec: wrap cpu_ldst.h in CONFIG_TCG
accel/stubs: reduce headers from tcg-stub
tests/plugin: add hotpages to analyse memory access patterns
tests/plugin: add instruction execution breakdown
tests/plugin: add a hotblocks plugin
tests/tcg: enable plugin testing
tests/tcg: drop test-i386-fprem from TESTS when not SLOW
tests/tcg: move "virtual" tests to EXTRA_TESTS
tests/tcg: set QEMU_OPTS for all cris runs
tests/tcg/Makefile.target: fix path to config-host.mak
tests/plugin: add sample plugins
linux-user: support -plugin option
vl: support -plugin option
plugin: add qemu_plugin_outs helper
plugin: add qemu_plugin_insn_disas helper
plugin: expand the plugin_init function to include an info block
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
