Users of struct Range mess liberally with its members, which makes
refactoring hard. Create a set of methods, and convert all users to
call them instead of accessing members. The methods have carefully
worded contracts, and use assertions to check them.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
PcPciInfo has two (ill-named) members: Range w32 is the PCI hole, and
w64 is the PCI64 hole.
Three users:
* I440FXState and MCHPCIState have a member PcPciInfo pci_info, but
only pci_info.w32 is actually used. This is confusing. Replace by
Range pci_hole.
* acpi_build() uses auto PcPciInfo pci_info to forward both PCI holes
from acpi_get_pci_info() to build_dsdt(). Replace by two variables
Range pci_hole, pci_hole64. Rename acpi_get_pci_info() to
acpi_get_pci_holes().
PcPciInfo is now unused; drop it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Range pci_info.w32 records the location of the PCI hole.
It's initialized to empty when QOM zeroes I440FXState. That's a fine
value for a still unknown PCI hole.
i440fx_init() sets pci_info.w32.begin = below_4g_mem_size. Changes
the PCI hole from empty to [below_4g_mem_size, UINT64_MAX]. That's a
bogus value.
i440fx_pcihost_initfn() sets pci_info.end = IO_APIC_DEFAULT_ADDRESS.
Since i440fx_init() ran already, this changes the PCI hole to
[below_4g_mem_size, IO_APIC_DEFAULT_ADDRESS-1]. That's the correct
value.
Setting the bounds of the PCI hole in two separate places is
confusing, and begs the question whether the bogus intermediate value
could be used by something, or what would happen if we somehow managed
to realize an i440FX device without having run the board init function
i440fx_init() first.
Avoid the confusion by setting the (constant) upper bound along with
the lower bound in i440fx_init().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Allow adding sysbus devices with -device on Q35.
At first Q35 will support only intel-iommu to be added this way,
however the command line will support all sysbus devices.
Mark with 'cannot_instantiate_with_device_add_yet' the ones
causing immediate problems (e.g. crashes).
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Similar to the previous patch, it's nice to have all functions
in the tree that involve a visitor and a name for conversion to
or from QAPI to consistently stick the 'name' parameter next
to the Visitor parameter.
Done by manually changing include/qom/object.h and qom/object.c,
then running this Coccinelle script and touching up the fallout
(Coccinelle insisted on adding some trailing whitespace).
@ rule1 @
identifier fn;
typedef Object, Visitor, Error;
identifier obj, v, opaque, name, errp;
@@
void fn
- (Object *obj, Visitor *v, void *opaque, const char *name,
+ (Object *obj, Visitor *v, const char *name, void *opaque,
Error **errp) { ... }
@@
identifier rule1.fn;
expression obj, v, opaque, name, errp;
@@
fn(obj, v,
- opaque, name,
+ name, opaque,
errp)
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1454075341-13658-20-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
JSON uses "name":value, but many of our visitor interfaces were
called with visit_type_FOO(v, &value, name, errp). This can be
a bit confusing to have to mentally swap the parameter order to
match JSON order. It's particularly bad for visit_start_struct(),
where the 'name' parameter is smack in the middle of the
otherwise-related group of 'obj, kind, size' parameters! It's
time to do a global swap of the parameter ordering, so that the
'name' parameter is always immediately after the Visitor argument.
Additional reason in favor of the swap: the existing include/qjson.h
prefers listing 'name' first in json_prop_*(), and I have plans to
unify that file with the qapi visitors; listing 'name' first in
qapi will minimize churn to the (admittedly few) qjson.h clients.
Later patches will then fix docs, object.h, visitor-impl.h, and
those clients to match.
Done by first patching scripts/qapi*.py by hand to make generated
files do what I want, then by running the following Coccinelle
script to affect the rest of the code base:
$ spatch --sp-file script `git grep -l '\bvisit_' -- '**/*.[ch]'`
I then had to apply some touchups (Coccinelle insisted on TAB
indentation in visitor.h, and botched the signature of
visit_type_enum() by rewriting 'const char *const strings[]' to
the syntactically invalid 'const char*const[] strings'). The
movement of parameters is sufficient to provoke compiler errors
if any callers were missed.
// Part 1: Swap declaration order
@@
type TV, TErr, TObj, T1, T2;
identifier OBJ, ARG1, ARG2;
@@
void visit_start_struct
-(TV v, TObj OBJ, T1 ARG1, const char *name, T2 ARG2, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, T2 ARG2, TErr errp)
{ ... }
@@
type bool, TV, T1;
identifier ARG1;
@@
bool visit_optional
-(TV v, T1 ARG1, const char *name)
+(TV v, const char *name, T1 ARG1)
{ ... }
@@
type TV, TErr, TObj, T1;
identifier OBJ, ARG1;
@@
void visit_get_next_type
-(TV v, TObj OBJ, T1 ARG1, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, TErr errp)
{ ... }
@@
type TV, TErr, TObj, T1, T2;
identifier OBJ, ARG1, ARG2;
@@
void visit_type_enum
-(TV v, TObj OBJ, T1 ARG1, T2 ARG2, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, T2 ARG2, TErr errp)
{ ... }
@@
type TV, TErr, TObj;
identifier OBJ;
identifier VISIT_TYPE =~ "^visit_type_";
@@
void VISIT_TYPE
-(TV v, TObj OBJ, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, TErr errp)
{ ... }
// Part 2: swap caller order
@@
expression V, NAME, OBJ, ARG1, ARG2, ERR;
identifier VISIT_TYPE =~ "^visit_type_";
@@
(
-visit_start_struct(V, OBJ, ARG1, NAME, ARG2, ERR)
+visit_start_struct(V, NAME, OBJ, ARG1, ARG2, ERR)
|
-visit_optional(V, ARG1, NAME)
+visit_optional(V, NAME, ARG1)
|
-visit_get_next_type(V, OBJ, ARG1, NAME, ERR)
+visit_get_next_type(V, NAME, OBJ, ARG1, ERR)
|
-visit_type_enum(V, OBJ, ARG1, ARG2, NAME, ERR)
+visit_type_enum(V, NAME, OBJ, ARG1, ARG2, ERR)
|
-VISIT_TYPE(V, OBJ, NAME, ERR)
+VISIT_TYPE(V, NAME, OBJ, ERR)
)
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1454075341-13658-19-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-11-git-send-email-peter.maydell@linaro.org
We can have at most one ISA bus. If you try to create another one,
isa_bus_new() complains to stderr and returns null.
isa_bus_new() is called in two contexts, machine's init() and device's
realize() methods. Since complaining to stderr is not proper in the
latter context, convert isa_bus_new() to Error.
Machine's init():
* mips_jazz_init(), called from the init() methods of machines
"magnum" and "pica"
* mips_r4k_init(), the init() method of machine "mips"
* pc_init1() called from the init() methods of non-q35 PC machines
* typhoon_init(), called from clipper_init(), the init() method of
machine "clipper"
These callers always create the first ISA bus, hence isa_bus_new()
can't fail. Simply pass &error_abort.
Device's realize():
* i82378_realize(), of PCI device "i82378"
* ich9_lpc_realize(), of PCI device "ICH9-LPC"
* pci_ebus_realize(), of PCI device "ebus"
* piix3_realize(), of PCI device "pci-piix3", abstract parent of
"PIIX3" and "PIIX3-xen"
* piix4_realize(), of PCI device "PIIX4"
* vt82c686b_realize(), of PCI device "VT82C686B"
Propagate the error. Note that these devices are typically created
only by machine init() methods with qdev_init_nofail() or similar. If
we screwed up and created an ISA bus before that call, we now give up
right away. Before, we'd hobble on, and typically die in
isa_bus_irqs(). Similar if someone finds a way to hot-plug one of
these critters.
Cc: Richard Henderson <rth@twiddle.net>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: "Hervé Poussineau" <hpoussin@reactos.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Markus Armbruster <armbru@pond.sub.org>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <1450370121-5768-11-git-send-email-armbru@redhat.com>
Fix the bug introduced by 595a4f07: function host_pci_config_read() should be
pass-by-reference, not value.
This probably means this function never worked for anyone.
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There's no indication of any sort that i440fx doesn't support
"iommu=on"
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Bandan Das <bsd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Bandan Das <bsd@redhat.com>
config_fd should be closed before return, or there will
be a resource leak error.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Implement a pci host bridge specific to passthrough. Actually
this just inherits the standard one. And we also just expose
a minimal real host bridge pci configuration subset.
[Replace pread with lseek and read to fix Windows build]
Signed-off-by: Tiejun Chen <tiejun.chen@intel.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
IGD passthrough wants to supply a different pci and
host devices, inheriting i440fx devices. Make types
configurable.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Tiejun Chen <tiejun.chen@intel.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
The existing i440fx initialization code sets a PCI config register that
isn't documented anywhere in the Intel 440FX datasheet. Register 0x57 is
DRAMC (DRAM Control) and has nothing to do with the RAM size.
This was implemented in commit ec5f92ce6a
because old coreboot code tried to read registers 0x5a-0x5f,0x56,0x57 to
get the RAM size from QEMU, but I couldn't find out why coreboot did
that. I assume it was a mistake, and the original code was supposed to
be reading the DRB[0-7] registers (offsets 0x60-0x67).
Document that coreboot-specific register offset in a macro and a
comment, for future reference.
Cc: Ed Swierk <eswierk@skyportsystems.com>
Cc: Richard Smith <smithbone@gmail.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We create optional sections with this patch. But we already have
optional subsections. Instead of having two mechanism that do the
same, we can just generalize it.
For subsections we just change:
- Add a needed function to VMStateDescription
- Remove VMStateSubsection (after removal of the needed function
it is just a VMStateDescription)
- Adjust the whole tree, moving the needed function to the corresponding
VMStateDescription
Signed-off-by: Juan Quintela <quintela@redhat.com>
It's easier to inline it now that most of its work is done by the CPU
(rather than the chipset) through /machine/smram and the memory API.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove cpu_smm_register and cpu_smm_update. Instead, each CPU
address space gets an extra region which is an alias of
/machine/smram. This extra region is enabled or disabled
as the CPU enters/exits SMM.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This region is exported at /machine/smram. It is "empty" if
SMRAME=0 and points to SMRAM if SMRAME=1. The CPU will
enable/disable it as it enters or exits SMRAM.
While touching nearby code, the existing memory region setup was
slightly inconsistent. The smram_region is *disabled* in order to open
SMRAM (because the smram_region shows the low VRAM instead of the RAM
at 0xa0000). Because SMRAM is closed at startup, the smram_region must
be enabled when creating the i440fx or q35 devices.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert the device models where initialization obviously can't fail.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Currently, keep current behaviour by always using get_system_memory().
Also use QOM casts when possible.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
This patch avoids setting an irq while loading the state of the ISA bridge.
Because the i8259 has not been deserialized yet, raising an interrupt
could bring the system out-of-sync with the migration source. For example,
the migration source could have masked the interrupt in the i8259. On the
destination, the i8259 device model would not know that yet and would
trigger an interrupt in the CPU.
This patch eliminates setting the irq and just restores the calculated
state fields in post_load function. Interrupt state will be deserialized
separately through the IRR field of the i8259.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After previous Peter patch, they are redundant. This way we don't
assign them except when needed. Once there, there were lots of case
where the ".fields" indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (appart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Acked-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Get rid of PCIDevice specific PCIDeviceClass.no_hotplug and use
generic DeviceClass.hotpluggable field instead.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This includes some Preparatory patches for cpu hotplug for q25 and memory
hotplug by Igor, tests and memory mapping change
by Laszlo and pci reset cleanup by Paolo.
There are also some fixes for fedora and virtio:
included here since they are test blockers for me.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSuF+2AAoJECgfDbjSjVRpTz0IAJhNCC8L2GVt+pm1RAt6lbqZ
u9bCrqfThDORN2mUTEuLu4ZpZC0DYc7d0Jjr5NPesC5G/Afzi5/to6+l7nNZneU3
OdBPglXCCfU/cRaLu7JG2akpha0GVU0tsSCoWIYa6mwlWA4/DXVMgeKg/bh/EgfM
B1w4fE2RgRM9bEqWmX4+tZw8dgk7uVJhu95HCDnb5eikaKlFzwuOlvexrDV3KbPc
bkJe35zbGrKOws93tiSeoqcDx2dcYSzecPoJ0jiCY0KXJ17PBWAvuLTtYqkwwe9J
2FEnTslQJ3Rc8jTFiOPWx2pGaejG4y7Tnk6uuzW6fbbSLOQDPJy3KgmutJFMt1A=
=ShCj
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
acpi,pci,pc,fedora,virtio fixes and enhancements
This includes some Preparatory patches for cpu hotplug for q25 and memory
hotplug by Igor, tests and memory mapping change
by Laszlo and pci reset cleanup by Paolo.
There are also some fixes for fedora and virtio:
included here since they are test blockers for me.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Mon 23 Dec 2013 08:07:18 AM PST using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
* mst/tags/for_anthony:
target-arm: fix build with gcc 4.8.2
virtio: add back call to virtio_bus_device_unplugged
piix: fix 32bit pci hole
qdev: switch reset to post-order
qdev: allow both pre- and post-order vists in qdev walking functions
pci: clean up resetting of IRQs
pci: do not export pci_bus_reset
ACPI/DSDT-CPU: cleanup bogus comment
ACPI: Q35 DSDT: fix CPU hotplug GPE0.2 handler
acpi: ich9: allow guest to clear SCI rised by GPE
acpi: factor out common pm_update_sci() into acpi core
acpi: piix4: remove not needed GPE0 mask
i440fx-test: verify firmware under 4G and 1M, both -bios and -pflash
i440fx-test: generate temporary firmware blob
i440fx-test: give each GTest case its own qtest
i440fx-test: qtest_start() should be paired with qtest_end()
hw/i386/pc_sysfw: support two flash drives
pc_piix: document gigabyte_align
piix: gigabyte alignment for ram
Message-id: 1387815007-1272-1-git-send-email-mst@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Make the 32bit pci hole start at end of ram, so all possible address
space is covered.
We used to try and make addresses aligned so they are easier to cover
with MTRRs, but since they are cosmetic on KVM, this is probably not
worth worrying about.
Of course the firmware can use less than that. Leaving space unused is
no problem, mapping pci bars outside the hole causes problems though.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A PIIX3/PIIX4 southbridge has multiple functions. We model each
function as a separate qdev. Two of them need some special wiring set
up in pc_init1() or mips_malta_init() to work: the ISA bridge at 01.0,
and the SMBus controller at 01.3.
The IDE controller at 01.1 (piix3-ide, piix3-ide-xen, piix4-ide) has
always had cannot_instantiate_with_device_add_yet set, but there is no
obvious reason why device_add could not work for them. Drop it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Many PCI host bridges consist of a sysbus device and a PCI device.
You need both for the thing to work. Arguably, these bridges should
be modelled as a single, composite devices instead of pairs of
seemingly independent devices you can only use together, but we're not
there, yet.
Since the sysbus part can't be instantiated with device_add, yet,
permitting it with the PCI part is useless. We shouldn't offer
useless options to the user, so let's set
cannot_instantiate_with_device_add_yet for them.
It's already set for Bonito, Grackle, i440FX and Raven. Document why.
Set it for the others: dec-21154, e500-host-bridge, gt64120_pci, mch,
pbm-pci, ppc4xx-host-bridge, sh_pci_host, u3-agp, uni-north-agp,
uni-north-internal-pci, uni-north-pci, and versatile_pci_host.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
device_add plugs devices into suitable bus. For "real" buses, that
actually connects the device. For sysbus, the connections need to be
made separately, and device_add can't do that. The device would be
left unconnected, and could not possibly work.
Quite a few, but not all sysbus devices already set
cannot_instantiate_with_device_add_yet in their class init function.
Set it in their abstract base's class init function
sysbus_device_class_init(), and remove the now redundant assignments
from device class init functions.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
In an ideal world, machines can be built by wiring devices together
with configuration, not code. Unfortunately, that's not the world we
live in right now. We still have quite a few devices that need to be
wired up by code. If you try to device_add such a device, it'll fail
in sometimes mysterious ways. If you're lucky, you get an
unmysterious immediate crash.
To protect users from such badness, DeviceClass member no_user used to
make device models unavailable with -device / device_add, but that
regressed in commit 18b6dad. The device model is still omitted from
help, but is available anyway.
Attempts to fix the regression have been rejected with the argument
that the purpose of no_user isn't clear, and it's prone to misuse.
This commit clarifies no_user's purpose. Anthony suggested to rename
it cannot_instantiate_with_device_add_yet_due_to_internal_bugs, which
I shorten somewhat to keep checkpatch happy. While there, make it
bool.
Every use of cannot_instantiate_with_device_add_yet gets a FIXME
comment asking for rationale. The next few commits will clean them
all up, either by providing a rationale, or by getting rid of the use.
With that done, the regression fix is hopefully acceptable.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
With a help of negative memory region priority PCI address space
is mapped underneath RAM regions effectively catching every access
to addresses not mapped by any other region.
It simplifies PCI address space mapping into system address space.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
The following commit introduced a migration incompatibility:
commit 568f0690fd
Author: David Gibson <david@gibson.dropbear.id.au>
Date: Thu Jun 6 18:48:49 2013 +1000
pci: Replace pci_find_domain() with more general pci_root_bus_path()
The issue is that i440fx savevm idstr went from 0000:00:00.0/I440FX to
0000:00.0/I440FX. Unfortunately we are stuck with the breakage for
1.6 machine types.
Add a compat property to maintain the busted idstr for the 1.6 machine
types, but revert to the old style format for 1.7+, and <= 1.5.
Tested with migration from qemu 1.5, qemu 1.6, and qemu.git.
Cc: qemu-stable@nongnu.org
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This adds APIs that will be used to fill in guest acpi tables.
Some required information is still lacking in QOM, so we
fall back on lookups by type and returning explicit types.
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
commit 3984890181
pc: limit 64 bit hole to 2G by default
introduced a way for management to control
the window allocated to the 64 bit PCI hole.
This is useful, but existing management tools do not know how to set
this property. As a result, e.g. specifying a large ivshmem device with
size > 4G is broken by default. For example this configuration no
longer works:
-device ivshmem,size=4294967296,chardev=cfoo
-chardev socket,path=/tmp/sock,id=cfoo,server,nowait
Fix this by detecting that hole size was not specified
and defaulting to the backwards-compatible value of 1 << 62.
Cc: qemu-stable@nongnu.org
Cc: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It turns out that some 32 bit windows guests crash
if 64 bit PCI hole size is >2G.
Limit it to 2G for piix and q35 by default.
User may override default 64-bit PCI hole size by
using "pci-hole64-size" property.
Examples:
-global i440FX-pcihost.pci-hole64-size=4G
-global q35-pcihost.pci-hole64-size=4G
Reported-by: Igor Mammedov <imammedo@redhat.com>,
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Message-id: 1375109277-25561-8-git-send-email-imammedo@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
It isn't used anywhere else.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Message-id: 1375109277-25561-4-git-send-email-imammedo@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Message-id: 1375109277-25561-3-git-send-email-imammedo@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
[AF: Converted remaining accesses and renamed to parent_obj]
Signed-off-by: Andreas Färber <afaerber@suse.de>
This includes some pci enhancements:
Better support for systems with multiple PCI root buses
FW cfg interface for more robust pci programming in BIOS
Minor fixes/cleanups for fw cfg and cross-version migration -
because of dependencies with other patches
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJR2ctmAAoJECgfDbjSjVRpQpAH/Rk00yLrQ2R5ScNa8AL9LeaJ
gVFndBmmuRz4gdhyATx6lzR98ic32iTr0+YR5mL51btgmM5a0bEd/SIu34nXriWj
PsM0wdXfo/oEygdttxhvzJOH17tohRV9xg2WA2d8BEwDzrDyqoQ4J0VJlHlG7u3W
nq4KVDVUpLNQFKG8ZgJ2vW0WMw/mBSj2rluhQUALhcuvChphtvAFZ2rsSfJr6bzD
aBELrtIvfLvPGN/0WVeYs9qlp4EE03H3X6gN61QvV3/YElxubKUV5XyMDOX2dW3D
2j0NQi84LYHn0SFap2r/Kgm47/F6Q56SFk5lrgZrg60mhQTwocw7PfL8CGxjXRI=
=gxxc
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
pci,misc enhancements
This includes some pci enhancements:
Better support for systems with multiple PCI root buses
FW cfg interface for more robust pci programming in BIOS
Minor fixes/cleanups for fw cfg and cross-version migration -
because of dependencies with other patches
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Sun 07 Jul 2013 03:11:18 PM CDT using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
# By David Gibson (10) and others
# Via Michael S. Tsirkin
* mst/tags/for_anthony:
pci: Fold host_buses list into PCIHostState functionality
pci: Remove domain from PCIHostBus
pci: Simpler implementation of primary PCI bus
pci: Add root bus parameter to pci_nic_init()
pci: Add root bus argument to pci_get_bus_devfn()
pci: Replace pci_find_domain() with more general pci_root_bus_path()
pci: Use helper to find device's root bus in pci_find_domain()
pci: Abolish pci_find_root_bus()
pci: Move pci_read_devaddr to pci-hotplug-old.c
pci: Cleanup configuration for pci-hotplug.c
pvpanic: fix fwcfg for big endian hosts
pvpanic: initialization cleanup
MAINTAINERS: s/Marcelo/Paolo/
e1000: cleanup process_tx_desc
pc_piix: cleanup init compat handling
pc: pass PCI hole ranges to Guests
pci: store PCI hole ranges in guestinfo structure
range: add Range structure
Message-id: 1373228271-31223-1-git-send-email-mst@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
pci_find_domain() is used in a number of places where we want an id for a
whole PCI domain (i.e. the subtree under a PCI root bus). The trouble is
that many platforms may support multiple independent host bridges with no
hardware supplied notion of domain number.
This patch, therefore, replaces calls to pci_find_domain() with calls to
a new pci_root_bus_path() returning a string. The new call is implemented
in terms of a new callback in the host bridge class, so it can be defined
in some way that's well defined for the platform. When no callback is
available we fall back on the qbus name.
Most current uses of pci_find_domain() are for error or informational
messages, so the change in identifiers should be harmless. The exception
is pci_get_dev_path(), whose results form part of migration streams. To
maintain compatibility with old migration streams, the PIIX PCI host is
altered to always supply "0000" for this path, which matches the old domain
number (since the code didn't actually support domains other than 0).
For the pseries (spapr) PCI bridge we use a different platform-unique
identifier (pseries machines can routinely have dozens of PCI host
bridges). Theoretically that breaks migration streams, but given that we
don't yet have migration support for pseries, it doesn't matter.
Any other machines that have working migration support including PCI
devices will need to be updated to maintain migration stream compatibility.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
