Armv8.1+ cpus have Virtual Host Extension (VHE) which added non-secure
EL2 virtual timer.
This change adds it to fullfil Arm BSA (Base System Architecture)
requirements.
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Message-id: 20230913140610.214893-2-marcin.juszkiewicz@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This extends the slots of xhci to 64, since the default xhci_sysbus
just supports one slot.
Signed-off-by: Wang Yuquan <wangyuquan1236@phytium.com.cn>
Signed-off-by: Chen Baozi <chenbaozi@phytium.com.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Tested-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Message-id: 20230710063750.473510-2-wangyuquan1236@phytium.com.cn
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
pci_nic_init_nofail() calls qemu_find_nic_model(), and this function
sets nd->model = g_strdup(default_model) if it has not been initialized
yet. So we don't have to set nd->model to the default_nic in the
calling sites.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Now that we have implemented support for FEAT_LSE2, we can define
a CPU model for the Neoverse-V1, and enable it for the virt and
sbsa-ref boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230704130647.2842917-3-peter.maydell@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The current sbsa-ref cannot use EHCI controller which is only
able to do 32-bit DMA, since sbsa-ref doesn't have RAM below 4GB.
Hence, this uses XHCI to provide a usb controller with 64-bit
DMA capablity instead of EHCI.
We bump the platform version to 0.3 with this change. Although the
hardware at the USB controller address changes, the firmware and
Linux can both cope with this -- on an older non-XHCI-aware
firmware/kernel setup the probe routine simply fails and the guest
proceeds without any USB. (This isn't a loss of functionality,
because the old USB controller never worked in the first place.) So
we can call this a backwards-compatible change and only bump the
minor version.
Signed-off-by: Yuquan Wang <wangyuquan1236@phytium.com.cn>
Message-id: 20230621103847.447508-2-wangyuquan1236@phytium.com.cn
[PMM: tweaked commit message; add line to docs about what
changes in platform version 0.3]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
"sysemu/kvm.h" is indirectly pulled in. Explicit its
inclusion to avoid when refactoring include/:
hw/arm/sbsa-ref.c:693:9: error: implicit declaration of function 'kvm_enabled' is invalid in C99 [-Werror,-Wimplicit-function-declaration]
if (kvm_enabled()) {
^
Reviewed-by: Leif Lindholm <quic_llindhol@quicinc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230405160454.97436-6-philmd@linaro.org>
"kvm_arm.h" contains external and internal prototype declarations.
Files under the hw/ directory should only access the KVM external
API.
In order to avoid machine / device models to include "kvm_arm.h"
simply to get the QOM GIC/ITS class name, un-inline each class
name getter to the proper device model file.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230405160454.97436-4-philmd@linaro.org>
There are two ARM machines where NUMA is aware: 'virt' and 'sbsa-ref'.
Both of them are required to follow cluster-NUMA-node boundary. To
enable the validation to warn about the irregular configuration where
multiple CPUs in one cluster have been associated with different NUMA
nodes.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230509002739.18388-3-gshan@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Create ITS as part of SBSA platform GIC initialization.
GIC ITS information is in DeviceTree so TF-A can pass it to EDK2.
Bumping platform version to 0.2 as this is important hardware change.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Message-id: 20230619170913.517373-2-marcin.juszkiewicz@linaro.org
Co-authored-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let add GIC information into DeviceTree as part of SBSA-REF versioning.
Trusted Firmware will read it and provide to next firmware level.
Bumps platform version to 0.1 one so we can check is node is present.
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Mark the default NIC via the new MachineClass->default_nic setting
so that the machine-defaults code in vl.c can decide whether the
default NIC is usable or not (for example when compiling with the
"--without-default-devices" configure switch).
Message-Id: <20230524082037.1620952-1-thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Bochs card is normal PCI Express card so it fits better in system with
PCI Express bus. VGA is simple legacy PCI card.
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Reviewed-by: Leif Lindholm <quic_llindhol@quicinc.com>
Message-id: 20230505120936.1097060-1-marcin.juszkiewicz@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The world outside moves to newer and newer cpu cores. Let move SBSA
Reference Platform to something newer as well.
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Reviewed-by: Leif Lindholm <quic_llindhol@quicinc.com>
Message-id: 20230506183417.1360427-1-marcin.juszkiewicz@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ide_create_drive() operates on a IDEBus; rename it as
ide_bus_create_drive() to emphasize its first argument
is a IDEBus.
Mechanical change using:
$ sed -i -e 's/ide_create_drive/ide_bus_create_drive/g' \
$(git grep -wl ide_create_drive)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-12-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Cortex-A76 supports 40bits of address space. sbsa-ref's memory
starts above this limit.
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230126114416.2447685-1-marcin.juszkiewicz@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use the macro instead of two explicit string literals.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20230124232059.4017615-1-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The sbsa-ref machine is continuously evolving. Some of the changes we
want to make in the near future, to align with real components (e.g.
the GIC-700), will break compatibility for existing firmware.
Introduce two new properties to the DT generated on machine generation:
- machine-version-major
To be incremented when a platform change makes the machine
incompatible with existing firmware.
- machine-version-minor
To be incremented when functionality is added to the machine
without causing incompatibility with existing firmware.
to be reset to 0 when machine-version-major is incremented.
This versioning scheme is *neither*:
- A QEMU versioned machine type; a given version of QEMU will emulate
a given version of the platform.
- A reflection of level of SBSA (now SystemReady SR) support provided.
The version will increment on guest-visible functional changes only,
akin to a revision ID register found on a physical platform.
These properties are both introduced with the value 0.
(Hence, a machine where the DT is lacking these nodes is equivalent
to version 0.0.)
Signed-off-by: Leif Lindholm <quic_llindhol@quicinc.com>
Message-id: 20220505113947.75714-1-quic_llindhol@quicinc.com
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Radoslaw Biernacki <rad@semihalf.com>
Cc: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Enable the n1 for virt and sbsa board use.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220506180242.216785-25-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Enable the a76 for virt and sbsa board use.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220506180242.216785-24-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We use the arm_boot_info::nb_cpus field in only one place, and that
place can easily get the number of CPUs locally rather than relying
on the board code to have set the field correctly. (At least one
board, xlnx-versal-virt, does not set the field despite having more
than one CPU.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-16-peter.maydell@linaro.org
A lot of C files in hw/arm include qemu-common.h when they don't
need anything from it. Drop the include lines.
omap1.c, pxa2xx.c and strongarm.c retain the include because they
use it for the prototype of qemu_get_timedate().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Taylor Simpson <tsimpson@quicinc.com>
Reviewed-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Message-id: 20211129200510.1233037-5-peter.maydell@linaro.org
The SBSA_GWDT enum value conflicts with the SBSA_GWDT() QOM type
checking helper, preventing us from using a OBJECT_DEFINE* or
DEFINE_INSTANCE_CHECKER macro for the SBSA_GWDT() wrapper.
If I understand the SBSA 6.0 specification correctly, the signal
being connected to IRQ 16 is the WS0 output signal from the
Generic Watchdog. Rename the enum value to SBSA_GWDT_WS0 to be
more explicit and avoid the name conflict.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-id: 20210806023119.431680-1-ehabkost@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the user provides both a BIOS/firmware image and also a guest
kernel filename, arm_setup_firmware_boot() will pass the
kernel image to the firmware via the fw_cfg device. However we
weren't checking whether there really was a fw_cfg device present,
and if there wasn't we would crash.
This crash can be provoked with a command line such as
qemu-system-aarch64 -M raspi3 -kernel /dev/null -bios /dev/null -display none
It is currently only possible on the raspi3 machine, because unless
the machine sets info->firmware_loaded we won't call
arm_setup_firmware_boot(), and the only machines which set that are:
* virt (has a fw-cfg device)
* sbsa-ref (checks itself for kernel_filename && firmware_loaded)
* raspi3 (crashes)
But this is an unfortunate beartrap to leave for future machine
model implementors, so we should handle this situation in boot.c.
Check in arm_setup_firmware_boot() whether the fw-cfg device exists
before trying to load files into it, and if it doesn't exist then
exit with a hopefully helpful error message.
Because we now handle this check in a machine-agnostic way, we
can remove the check from sbsa-ref.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/503
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210726163351.32086-1-peter.maydell@linaro.org
Stop including exec/address-spaces.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-5-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Let add 'max' cpu while work goes on adding newer CPU types than
Cortex-A72. This allows us to check SVE etc support.
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Acked-by: Leif Lindholm <leif@nuviainc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210216150122.3830863-3-marcin.juszkiewicz@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Get the firmware name from the MachineState object.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20201026143028.3034018-4-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Trusted Firmware now supports A72 on sbsa-ref by default [1] so enable
it for QEMU as well. A53 was already enabled there.
1. https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/7117
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201120141705.246690-1-marcin.juszkiewicz@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Included the newly implemented SBSA generic watchdog device model into
SBSA platform
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20201027015927.29495-3-shashi.mallela@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Original commit did not allocate IRQs for the SMMUv3 in the irqmap
effectively using irq 0->3 (shared with other devices). Assuming
original intent was to allocate unique IRQs then add an allocation
to the irqmap.
Fixes: e9fdf45324 ("hw/arm: Add arm SBSA reference machine, devices part")
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Graeme Gregory <graeme@nuviainc.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20201007100732.4103790-3-graeme@nuviainc.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
SMMUv3 has an error in a previous patch where an i was transposed to a 1
meaning interrupts would not have been correctly assigned to the SMMUv3
instance.
Fixes: 48ba18e6d3 ("hw/arm/sbsa-ref: Simplify by moving the gic in the machine state")
Signed-off-by: Graeme Gregory <graeme@nuviainc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20201007100732.4103790-2-graeme@nuviainc.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It is defined twice already. Move to a common header file to
remove duplication and make it available to everybody.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20200928104256.9241-2-kraxel@redhat.com
When debugging QEMU it is often useful to put a breakpoint on the
error_setg_internal method impl.
Unfortunately the object_property_add / object_class_property_add
methods call object_property_find / object_class_property_find methods
to check if a property exists already before adding the new property.
As a result there are a huge number of calls to error_setg_internal
on startup of most QEMU commands, making it very painful to set a
breakpoint on this method.
Most callers of object_find_property and object_class_find_property,
however, pass in a NULL for the Error parameter. This simplifies the
methods to remove the Error parameter entirely, and then adds some
new wrapper methods that are able to raise an Error when needed.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200914135617.1493072-1-berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add the previously created sbsa-ec device to the sbsa-ref machine in
secure memory so the PSCI implementation in ARM-TF can access it, but
not expose it to non secure firmware or OS except by via ARM-TF.
Signed-off-by: Graeme Gregory <graeme@nuviainc.com>
Reviewed-by: Leif Lindholm <leif@nuviainc.com>
Tested-by: Leif Lindholm <leif@nuviainc.com>
Message-id: 20200826141952.136164-3-graeme@nuviainc.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The sbsa-ref platform uses a minimal device tree to pass amount of memory
as well as number of cpus to the firmware. However, when dumping that
minimal dtb (with -M sbsa-virt,dumpdtb=<file>), the resulting blob
generates a warning when decompiled by dtc due to lack of reg property.
Add a simple reg property per cpu, representing a 64-bit MPIDR_EL1.
This also ends up being cleaner than having the firmware calculating its
own IDs for generating APCI.
Signed-off-by: Leif Lindholm <leif@nuviainc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200827124335.30586-1-leif@nuviainc.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fixing a typo in a previous patch that translated an "i" to a 1
and therefore breaking the allocation of PCIe interrupts. This was
discovered when virtio-net-pci devices ceased to function correctly.
Cc: qemu-stable@nongnu.org
Fixes: 48ba18e6d3 ("hw/arm/sbsa-ref: Simplify by moving the gic in the machine state")
Signed-off-by: Graeme Gregory <graeme@nuviainc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200821083853.356490-1-graeme@nuviainc.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The object_property_set_FOO() setters take property name and value in
an unusual order:
void object_property_set_FOO(Object *obj, FOO_TYPE value,
const char *name, Error **errp)
Having to pass value before name feels grating. Swap them.
Same for object_property_set(), object_property_get(), and
object_property_parse().
Convert callers with this Coccinelle script:
@@
identifier fun = {
object_property_get, object_property_parse, object_property_set_str,
object_property_set_link, object_property_set_bool,
object_property_set_int, object_property_set_uint, object_property_set,
object_property_set_qobject
};
expression obj, v, name, errp;
@@
- fun(obj, v, name, errp)
+ fun(obj, name, v, errp)
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Convert that one manually.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Fails to convert hw/rx/rx-gdbsim.c, because Coccinelle gets confused
by RXCPU being used both as typedef and function-like macro there.
Convert manually. The other files using RXCPU that way don't need
conversion.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-27-armbru@redhat.com>
[Straightforwad conflict with commit 2336172d9b "audio: set default
value for pcspk.iobase property" resolved]
All remaining conversions to qdev_realize() are for bus-less devices.
Coccinelle script:
// only correct for bus-less @dev!
@@
expression errp;
expression dev;
@@
- qdev_init_nofail(dev);
+ qdev_realize(dev, NULL, &error_fatal);
@ depends on !(file in "hw/core/qdev.c") && !(file in "hw/core/bus.c")@
expression errp;
expression dev;
symbol true;
@@
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize(DEVICE(dev), NULL, errp);
@ depends on !(file in "hw/core/qdev.c") && !(file in "hw/core/bus.c")@
expression errp;
expression dev;
symbol true;
@@
- object_property_set_bool(dev, true, "realized", errp);
+ qdev_realize(DEVICE(dev), NULL, errp);
Note that Coccinelle chokes on ARMSSE typedef vs. macro in
hw/arm/armsse.c. Worked around by temporarily renaming the macro for
the spatch run.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-57-armbru@redhat.com>
Same transformation as in the previous commit. Manual, because
convincing Coccinelle to transform these cases is somewhere between
not worthwhile and infeasible (at least for me).
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-11-armbru@redhat.com>
This is the transformation explained in the commit before previous.
Takes care of just one pattern that needs conversion. More to come in
this series.
Coccinelle script:
@ depends on !(file in "hw/arm/highbank.c")@
expression bus, type_name, dev, expr;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr;
identifier DOWN;
@@
- dev = DOWN(qdev_create(bus, type_name));
+ dev = DOWN(qdev_new(type_name));
... when != dev = expr
- qdev_init_nofail(DEVICE(dev));
+ qdev_realize_and_unref(DEVICE(dev), bus, &error_fatal);
@@
expression bus, type_name, expr;
identifier dev;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr, errp;
symbol true;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
@@
expression bus, type_name, expr, errp;
identifier dev;
symbol true;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
The first rule exempts hw/arm/highbank.c, because it matches along two
control flow paths there, with different @type_name. Covered by the
next commit's manual conversions.
Missing #include "qapi/error.h" added manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-10-armbru@redhat.com>
[Conflicts in hw/misc/empty_slot.c and hw/sparc/leon3.c resolved]
Use the QEMU_IS_ALIGNED() macro to verify the flash block size
is properly aligned. It is quicker to process when reviewing.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200511205246.24621-1-philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The only way object_property_add() can fail is when a property with
the same name already exists. Since our property names are all
hardcoded, failure is a programming error, and the appropriate way to
handle it is passing &error_abort.
Same for its variants, except for object_property_add_child(), which
additionally fails when the child already has a parent. Parentage is
also under program control, so this is a programming error, too.
We have a bit over 500 callers. Almost half of them pass
&error_abort, slightly fewer ignore errors, one test case handles
errors, and the remaining few callers pass them to their own callers.
The previous few commits demonstrated once again that ignoring
programming errors is a bad idea.
Of the few ones that pass on errors, several violate the Error API.
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call. ich9_pm_add_properties(), sparc32_ledma_realize(),
sparc32_dma_realize(), xilinx_axidma_realize(), xilinx_enet_realize()
are wrong that way.
When the one appropriate choice of argument is &error_abort, letting
users pick the argument is a bad idea.
Drop parameter @errp and assert the preconditions instead.
There's one exception to "duplicate property name is a programming
error": the way object_property_add() implements the magic (and
undocumented) "automatic arrayification". Don't drop @errp there.
Instead, rename object_property_add() to object_property_try_add(),
and add the obvious wrapper object_property_add().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-15-armbru@redhat.com>
[Two semantic rebase conflicts resolved]
This uses TYPE_PL011 when creating the serial port so that the code
looks cleaner.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200224222223.4128-1-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
memory_region_allocate_system_memory() API is going away, so
replace it with memdev allocated MemoryRegion. The later is
initialized by generic code, so board only needs to opt in
to memdev scheme by providing
MachineClass::default_ram_id
and using MachineState::ram instead of manually initializing
RAM memory region.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200219160953.13771-31-imammedo@redhat.com>
