Return a valid value from the BCM2835 property mailbox query "get board
revision". This query is used by U-Boot. Implementing it fixes the first
obvious difference between qemu and real HW.
The value returned is currently hard-coded to match the RPi2 I own. Other
values are legal, e.g. different board manufacturer field values are
likely to exist in the wild.
Cc: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1454993910-24077-1-git-send-email-swarren@wwwdotorg.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds the SAS1068 device, a SAS disk controller used in VMware that
is oldish but widely supported and has decent performance. Unlike
megasas, it presents itself as a SAS controller and not as a RAID
controller. The device corresponds to the mptsas kernel driver in
Linux.
A few small things in the device setup are based on Don Slutz's old
patch, but the device emulation was written from scratch based on Don's
SeaBIOS patch and on the FreeBSD and Linux drivers. It is 2400 lines
shorter than Don's patch (and roughly the same size as MegaSAS---also
because it doesn't support the similar SPI controller), implements SCSI
task management functions (with asynchronous cancellation), supports
big-endian hosts, has complete support for migration and follows the
QEMU coding standards much more closely.
To write the driver, I first split Don's patch in two parts, with
the configuration bits in one file and the rest in a separate file.
I first left mptconfig.c in place and rewrote the rest, then deleted
mptconfig.c as well. The configuration pages are still based mostly on
VirtualBox's, though not exactly the same. However, the implementation
is completely different. The contents of the pages themselves should
not be copyrightable.
Signed-off-by: Don Slutz <Don@CloudSwitch.com>
Message-Id: <1347382813-5662-1-git-send-email-Don@CloudSwitch.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SAS adapters need to access them in order to publish the SAS addresses
of the end devices connected to them.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Included here:
Refactoring and bugfix patches in PC/ACPI.
New commands for ipmi.
Virtio optimizations.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWtj8KAAoJECgfDbjSjVRpBIQIAJSB9xwTcBLXwD0+8z5lqjKC
GTtuVbHU0+Y/eO8O3llN5l+SzaRtPHo18Ele20Oz7IQc0ompANY273K6TOlyILwB
rOhrub71uqpOKbGlxXJflroEAXb78xVK02lohSUvOzCDpwV+6CS4ZaSer7yDCYkA
MODZj7rrEuN0RmBWqxbs1R7Mj2CeQJzlgTUNTBGCLEstoZGFOJq8FjVdG5P1q8vI
fnI9mGJ1JsDnmcUZe/bTFfB4VreqeQ7UuGyNAMMGnvIbr0D1a+CoaMdV7/HZ+KyT
5TIs0siVdhZei60A/Cq2OtSVCbj5QdxPBLhZfwJCp6oU4lh2U5tSvva0mh7MwJ0=
=D/cA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc and misc cleanups and fixes, virtio optimizations
Included here:
Refactoring and bugfix patches in PC/ACPI.
New commands for ipmi.
Virtio optimizations.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Sat 06 Feb 2016 18:44:26 GMT using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream: (45 commits)
net: set endianness on all backend devices
fix MSI injection on Xen
intel_iommu: large page support
dimm: Correct type of MemoryHotplugState->base
pc: set the OEM fields in the RSDT and the FADT from the SLIC
acpi: add function to extract oem_id and oem_table_id from the user's SLIC
acpi: expose oem_id and oem_table_id in build_rsdt()
acpi: take oem_id in build_header(), optionally
pc: Eliminate PcGuestInfo struct
pc: Move APIC and NUMA data from PcGuestInfo to PCMachineState
pc: Move PcGuestInfo.fw_cfg to PCMachineState
pc: Remove PcGuestInfo.isapc_ram_fw field
pc: Remove RAM size fields from PcGuestInfo
pc: Remove compat fields from PcGuestInfo
acpi: Don't save PcGuestInfo on AcpiBuildState
acpi: Remove guest_info parameters from functions
pc: Simplify xen_load_linux() signature
pc: Simplify pc_memory_init() signature
pc: Eliminate struct PcGuestInfoState
pc: Move PcGuestInfo declaration to top of file
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On Xen MSIs can be remapped into pirqs, which are a type of event
channels. It's mostly for the benefit of PCI passthrough devices, to
avoid the overhead of interacting with the emulated lapic.
However remapping interrupts and MSIs is also supported for emulated
devices, such as the e1000 and virtio-net.
When an interrupt or an MSI is remapped into a pirq, masking and
unmasking is done by masking and unmasking the event channel. The
masking bit on the PCI config space or MSI-X table should be ignored,
but it isn't at the moment.
As a consequence emulated devices which use MSI or MSI-X, such as
virtio-net, don't work properly (the guest doesn't receive any
notifications). The mechanism was working properly when xen_apic was
introduced, but I haven't narrowed down which commit in particular is
causing the regression.
Fix the issue by ignoring the masking bit for MSI and MSI-X which have
been remapped into pirqs.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Current intel_iommu only supports 4K page which may not be sufficient
to cover guest working set. This patch tries to enable 2M and 1G mapping
for intel_iommu. This is also useful for future device IOTLB
implementation to have a better hit rate.
Major work is adding a page mask field on IOTLB entry to make it
support large page. And also use the slpte level as key to do IOTLB
lookup. MAMV was increased to 18 to support direct invalidation for 1G
mapping.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The 'base' field of MemoryHotplugState is ram_addr_t, which indicates that
it exists in the abstract address space of RAM regions.
However, the actual usage of this field indicates that it is a concrete
physical address (it's passed as an offset to memory_region_add_subgregion
for example).
So, correct its type to 'hwaddr'.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
The acpi_get_slic_oem() function stores pointers to these fields in the
(first) SLIC table that the user passes in with the -acpitable switch.
Cc: "Michael S. Tsirkin" <mst@redhat.com> (supporter:ACPI/SMBIOS)
Cc: Igor Mammedov <imammedo@redhat.com> (supporter:ACPI/SMBIOS)
Cc: Richard W.M. Jones <rjones@redhat.com>
Cc: Aleksei Kovura <alex3kov@zoho.com>
Cc: Michael Tokarev <mjt@tls.msk.ru>
Cc: Steven Newbury <steve@snewbury.org.uk>
RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=1248758
LP: https://bugs.launchpad.net/qemu/+bug/1533848
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Steven Newbury <steve@snewbury.org.uk>
Since build_rsdt() is implemented as common utility code (in
"hw/acpi/aml-build.c"), it should expose -- and forward -- the oem_id and
oem_table_id parameters between board code and the generic build_header()
function.
Cc: "Michael S. Tsirkin" <mst@redhat.com> (supporter:ACPI/SMBIOS)
Cc: Igor Mammedov <imammedo@redhat.com> (supporter:ACPI/SMBIOS)
Cc: Shannon Zhao <zhaoshenglong@huawei.com> (maintainer:ARM ACPI Subsystem)
Cc: Paolo Bonzini <pbonzini@redhat.com> (maintainer:X86)
Cc: Richard W.M. Jones <rjones@redhat.com>
Cc: Aleksei Kovura <alex3kov@zoho.com>
Cc: Michael Tokarev <mjt@tls.msk.ru>
Cc: Steven Newbury <steve@snewbury.org.uk>
RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=1248758
LP: https://bugs.launchpad.net/qemu/+bug/1533848
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
This patch is the continuation of commit 8870ca0e94 ("acpi: support
specified oem table id for build_header"). It will allow us to control the
OEM ID field too in the SDT header.
Cc: "Michael S. Tsirkin" <mst@redhat.com> (supporter:ACPI/SMBIOS)
Cc: Igor Mammedov <imammedo@redhat.com> (supporter:ACPI/SMBIOS)
Cc: Xiao Guangrong <guangrong.xiao@linux.intel.com> (maintainer:NVDIMM)
Cc: Shannon Zhao <zhaoshenglong@huawei.com> (maintainer:ARM ACPI Subsystem)
Cc: Paolo Bonzini <pbonzini@redhat.com> (maintainer:X86)
Cc: Richard W.M. Jones <rjones@redhat.com>
Cc: Aleksei Kovura <alex3kov@zoho.com>
Cc: Michael Tokarev <mjt@tls.msk.ru>
Cc: Steven Newbury <steve@snewbury.org.uk>
RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=1248758
LP: https://bugs.launchpad.net/qemu/+bug/1533848
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
The struct is not used for anything, now.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
The code can use the PCMachineClass.pci_enabled field directly.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
The ACPI code can use the PCMachineState fields directly.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Remove the fields: legacy_acpi_table_size, has_acpi_build,
has_reserved_memory, and rsdp_in_ram from PcGuestInfo, and let
the existing code use the PCMachineClass fields directly.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
We can get the PcGuestInfo struct directly from PCMachineState,
and the return value is not needed at all.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
We can get the PcGuestInfo struct directly from PCMachineState,
and the return value is not needed at all.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Instead of allocating a new struct just for PcGuestInfo and the
mchine_done Notifier, place them inside PCMachineState.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
The struct will be used inside PCMachineState.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Currently, sdr attributes are identified using byte offsets and this
can be a bit confusing.
This patch adds a struct ipmi_sdr_compact conforming to the IPMI specs
and replaces byte offsets with names. It also introduces and uses a
struct ipmi_sdr_header in sections of the code where no assumption is
made on the type of SDR. This leave rooms to potential usage of other
types in the future.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Allocate the arrays for in_addr/out_addr/in_sg/out_sg outside the
VirtQueueElement. For now, virtqueue_pop and vring_pop keep
allocating a very large VirtQueueElement.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move allocation to virtio functions also when loading/saving a
VirtQueueElement. This will also let the load/save functions
keep backwards compatibility when the VirtQueueElement layout
is changed.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The return code of virtqueue_pop/vring_pop is unused except to check for
errors or 0. We can thus easily move allocation inside the functions
and just return a pointer to the VirtQueueElement.
The advantage is that we will be able to allocate only the space that
is needed for the actual size of the s/g list instead of the full
VIRTQUEUE_MAX_SIZE items. Currently VirtQueueElement takes about 48K
of memory, and this kind of allocation puts a lot of stress on malloc.
By cutting the size by two or three orders of magnitude, malloc can
use much more efficient algorithms.
The patch is pretty large, but changes to each device are testable
more or less independently. Splitting it would mostly add churn.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The next patch will make virtqueue_pop/vring_pop allocate memory for
the VirtQueueElement. In some cases (blk, scsi, gpu) the device wants
to extend VirtQueueElement with device-specific fields and, until now,
the place of the VirtQueueElement within the containing struct didn't
matter. When allocating the entire block in virtqueue_pop/vring_pop,
however, the containing struct must basically be a "subclass" of
VirtQueueElement, with the VirtQueueElement as the first field. Make
that the case for blk and scsi; gpu is already doing it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Version: GnuPG v1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=UnwI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jnsnow/tags/ide-pull-request' into staging
# gpg: Signature made Wed 03 Feb 2016 20:29:54 GMT using RSA key ID AAFC390E
# gpg: Good signature from "John Snow (John Huston) <jsnow@redhat.com>"
* remotes/jnsnow/tags/ide-pull-request:
dma: remove now useless DMA_* functions
sb16: use IsaDma interface instead of global DMA_* functions
gus: use IsaDma interface instead of global DMA_* functions
cs4231a: use IsaDma interface instead of global DMA_* functions
fdc: use IsaDma interface instead of global DMA_* functions
sparc64: disable floppy DMA
sparc: disable floppy DMA
magnum: disable floppy DMA for now
i8257: implement the IsaDma interface
isa: add an ISA DMA interface, and store it within the ISA bus
i8257: move state definition to new independent header
i8257: QOM'ify
i8257: add missing const
i8257: make the DMA running method per controller
i8257: rename functions to start with i8257_ prefix
i8257: rename struct dma_regs to I8257Regs
i8257: rename struct dma_cont to I8257State
i8257: pass ISA bus to DMA_init() function
i82374: device only existed as ISA device, so simplify device
fdc: fix detection under Linux
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Keep only DMA_init function as a wrapper around DMA controllers creation.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-20-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
This will permit to deprecate global DMA_*() functions.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-11-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
We will now be able to embed the i8257 interrupt controller in another object.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-10-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
i8257 DMA controller exists on one ISA bus, so let's specify it at initialization.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-3-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
The new version is slightly different, to support Rasbperry Pi (in
particular, Pi1's arm11 core which doesn't support v7 instructions
such as MOVW).
Tested-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is the SoC for Raspberry Pi 2.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This module is specific to the bcm2836 (Pi2). It implements the top
level interrupt controller, and mailboxes used for inter-processor
synchronisation.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This device maintains all the non-CPU peripherals on bcm2835 (Pi1)
which are also present on bcm2836 (Pi2). It also implements the
private address spaces used for DMA and mailboxes.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This sits behind the mailbox interface, and implements
request/response queries for system properties. The
framebuffer-related properties will be added in a later patch.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds the system mailboxes which are used to communicate with a
number of GPU peripherals on Pi/Pi2.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
in current impl. condition
build_madt() {
...
if (test_bit(i, cpuinfo->found_cpus))
is always true since loop handles only present CPUs
in range [0..smp_cpus).
But to fill usless cpuinfo->found_cpus we do unnecessary
scan over QOM tree to find the same CPUs.
So mark GICC as present always and drop not needed
code that fills cpuinfo->found_cpus.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1454323689-248759-1-git-send-email-imammedo@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
So we can stop rendering for a while in case we have to.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
We'll go take out the commands we receive out of the virt queue and put
them into a linked list, to decouple virtio queue handling from actual
command processing.
Also move cmd processing to new virtio_gpu_handle_ctrl func, so we can
easily kick it from different places.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Make use of the BDS-BB removal and insertion notifiers to remove or set
up, respectively, virtio-scsi's op blockers.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
rtas_st_buffer_direct() is a not particularly useful wrapper around
cpu_physical_memory_write(). All the callers are in
rtas_ibm_configure_connector, where it's better handled by local helper.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
rtas_st_buffer() appears in spapr.h as though it were a widely used helper,
but in fact it is only used for saving data in a format used by
rtas_ibm_get_system_parameter(). This changes it to a local helper more
specifically for that function.
While we're there fix a couple of small defects in
rtas_ibm_get_system_parameter:
- For the string value SPLPAR_CHARACTERISTICS, it wasn't including the
terminating \0 in the length which it should according to LoPAPR
7.3.16.1
- It now checks that the supplied buffer has at least enough space for
the length of the returned data, and returns an error if it does not.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Until the previous patch this relied on xc_fd(), which was only
implemented for Xen 4.0 and earlier.
Given this wasn't working since Xen 4.0 I have marked this as disabled
by default.
Removing this support drops the use of a bunch of symbols from
libxenctrl, specifically:
- xc_domain_create
- xc_domain_destroy
- xc_domain_getinfo
- xc_domain_max_vcpus
- xc_domain_setmaxmem
- xc_domain_unpause
- xc_evtchn_alloc_unbound
- xc_linux_build
This is another step towards only using Xen libraries which provide a
stable inteface.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Using an existing libxenctrl handle after a fork was never
particularly safe (especially if foreign mappings existed at the time
of the fork) and the xc fd has been unavailable for many releases.
Reopen the handle after fork and therefore do away with xc_fd().
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
In Xen 4.7 we are refactoring parts libxenctrl into a number of
separate libraries which will provide backward and forward API and ABI
compatiblity.
Specifically libxenevtchn, libxengnttab and libxenforeignmemory.
Previous patches have already laid the groundwork for using these by
switching the existing compatibility shims to reflect the intefaces to
these libraries.
So all which remains is to update configure to detect the libraries
and enable their use. Although they are notionally independent we take
an all or nothing approach to the three libraries since they were
added at the same time.
The only non-obvious bit is that we now open a proper xenforeignmemory
handle for xen_fmem instead of reusing the xen_xc handle.
Build tested with 4.0 .. 4.6 (inclusive) and the patches targetting
4.7 which adds these libraries.
This uses CONFIG_XEN_CTRL_INTERFACE_VERSION == 471 to cover the
introduction of these new interfaces.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
In Xen 4.7 we are refactoring parts libxenctrl into a number of
separate libraries which will provide backward and forward API and ABI
compatiblity.
One such library will be libxenforeignmemory which provides access to
privileged foreign mappings and which will provide an interface
equivalent to xc_map_foreign_{pages,bulk}.
The new xenforeignmemory_map() function behaves like
xc_map_foreign_pages() when the err argument is NULL and like
xc_map_foreign_bulk() when err is non-NULL, which maps into the shim
here onto checking err == NULL and calling the appropriate old
function.
Note that xenforeignmemory_map() takes the number of pages before the
arrays themselves, in order to support potentially future use of
variable-length-arrays in the prototype (in the future, when Xen's
baseline toolchain requirements are new enough to ensure VLAs are
supported).
In preparation for adding support for libxenforeignmemory add support
to the <=4.0 and <=4.6 compat code in xen_common.h to allow us to
switch to using the new API. These shims will disappear for versions
of Xen which include libxenforeignmemory.
Since libxenforeignmemory will have its own handle type but for <= 4.6
the functionality is provided by using a libxenctrl handle we
introduce a new global xen_fmem alongside the existing xen_xc. In fact
we make xen_fmem a pointer to the existing xen_xc, which then works
correctly with both <=4.0 (xc handle is an int) and <=4.6 (xc handle
is a pointer). In the latter case xen_fmem is actually a double
indirect pointer, but it all falls out in the wash.
Unlike libxenctrl libxenforeignmemory has an explicit unmap function,
rather than just specifying that munmap should be used, so the unmap
paths are updated to use xenforeignmemory_unmap, which is a shim for
munmap on these versions of xen. The mappings in xen-hvm.c do not
appear to be unmapped (which makes sense for a qemu-dm process)
In fb_disconnect this results in a change from simply mmap over the
existing mapping (with an implicit munmap) to expliclty unmapping with
xenforeignmemory_unmap and then mapping the required anonymous memory
in the same hole. I don't think this is a problem since any other
thread which was racily touching this region would already be running
the risk of hitting the mapping halfway through the call. If this is
thought to be a problem then we could consider adding an extra API to
the libxenforeignmemory interface to replace a foreign mapping with
anonymous shared memory, but I'd prefer not to.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
In Xen 4.7 we are refactoring parts libxenctrl into a number of
separate libraries which will provide backward and forward API and ABI
compatiblity.
One such library will be libxengnttab which provides access to grant
tables.
In preparation for this switch the compatibility layer in xen_common.h
(which support building with older versions of Xen) to use what will
be the new library API. This means that the gnttab shim will disappear
for versions of Xen which include libxengnttab.
To simplify things for the <= 4.0.0 support we wrap the int fd in a
malloc(sizeof int) such that the handle is always a pointer. This
leads to less typedef headaches and the need for
XC_HANDLER_INITIAL_VALUE etc for these interfaces.
Note that this patch does not add any support for actually using
libxengnttab, it just adjusts the existing shims.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
