Each controller on the ast2400 has a memory range on which it maps its
flash module slaves. Each slave is assigned a memory segment for its
mapping that can be changed at bootime with the Segment Address
Register. This is not supported in the current implementation so we
are using the defaults provided by the specs.
Each SPI flash slave can then be accessed in two modes: Command and
User. When in User mode, accesses to the memory segment of the slaves
are translated in SPI transfers. When in Command mode, the HW
generates the SPI commands automatically and the memory segment is
accessed as if doing a MMIO. Other SPI controllers call that mode
linear addressing mode.
For this purpose, we are adding below each crontoller an array of
structs gathering for each SPI flash module, a segment rank, a
MemoryRegion to handle the memory accesses and the associated SPI
slave device, which should be a m25p80.
Only the User mode is supported for now but we are preparing ground
for the Command mode. The framework is sufficient to support Linux.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-8-git-send-email-clg@kaod.org
[PMM: Use g_new0() rather than g_malloc0()]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed AST2400 soc includes a static memory controller for the BMC
which supports NOR, NAND and SPI flash memory modules. This controller
has two modes : the SMC for the legacy interface which supports only
one module and the FMC for the new interface which supports up to five
modules. The AST2400 also includes a SPI only controller used for the
host firmware, commonly called BIOS on Intel. It can be used in three
mode : a SPI master, SPI slave and SPI pass-through
Below is the initial framework for the SMC controller (FMC mode only)
and the SPI controller: the sysbus object, MMIO for registers
configuration and controls. Each controller has a SPI bus and a
configurable number of CS lines for SPI flash slaves.
The differences between the controllers are small, so they are
abstracted using indirections on the register numbers.
Only SPI flash modules are supported.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-7-git-send-email-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: added one missing error_propagate]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This allows specifying the property via -drive if=none and creating
the flash device with -device.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-6-git-send-email-clg@kaod.org
[clg: added an extra fix for sabrelite_init()
keeping the test on flash_dev did not seem necessary. ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The maximum amount of storage that can be addressed by the m25p80 command
set is 4 GiB. However, cur_addr is currently a 64-bit integer. To avoid
further problems related to sign extension of signed 32-bit integer
expressions, change cur_addr to a 32 bit integer. Preserve migration
format by adding a dummy 4-byte field in place of the (big-endian)
high four bytes in the formerly 64-bit cur_addr field.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-5-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
s->cur_addr can be made to point outside s->storage, either by
writing a value >= 128 to s->ear (because s->ear * MAX_3BYTES_SIZE
is a signed integer and sign-extends into the 64-bit cur_addr),
or just by writing an address beyond the size of the flash being
emulated. Avoid the sign extension to make the code cleaner, and
on top of that mask s->cur_addr to s->size.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-4-git-send-email-clg@kaod.org
Reviewed by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When doing a read-modify-write cycle, QEMU uses the iovec after returning
from blk_aio_pwritev. m25p80 puts the iovec on the stack of blk_aio_pwritev's
caller, which causes trouble in this case. This has been a problem
since commit 243e6f6 ("m25p80: Switch to byte-based block access",
2016-05-12) started doing writes at a smaller granularity than 512 bytes.
In principle however it could have broken before when using -drive
if=mtd,cache=none on a disk with 4K native sectors.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-3-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This enables qemu to handle late inits and report errors. All the SSI
slave routine names were changed accordingly. Code was modified to
handle errors when possible (m25p80 and ssi-sd)
Tested with the m25p80 slave object.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-2-git-send-email-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a minimal model for the devcfg device which is part of Zynq.
This model supports DMA capabilities and interrupt generation.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 83df49d8fa2d203a421ca71620809e4b04754e65.1467053537.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a helper that will scan a static RegisterAccessInfo Array
and populate a container MemoryRegion with registers as defined.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 347b810b2799e413c98d5bbeca97bcb1557946c3.1467053537.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QOMify registers as a child of TYPE_DEVICE. This allows registers to
define GPIOs.
Define an init helper that will do QOM initialisation.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: KONRAD Frederic <fred.konrad@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 2545f71db26bf5586ca0c08a3e3cf1b217450552.1467053537.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Define some macros that can be used for defining registers and fields.
The REG32 macro will define A_FOO, for the byte address of a register
as well as R_FOO for the uint32_t[] register number (A_FOO / 4).
The FIELD macro will define FOO_BAR_MASK, FOO_BAR_SHIFT and
FOO_BAR_LENGTH constants for field BAR in register FOO.
Finally, there are some shorthand helpers for extracting/depositing
fields from registers based on these naming schemes.
Usage can greatly reduce the verbosity of device code.
The deposit and extract macros (eg FIELD_EX32, FIELD_DP32 etc.) can be
used to generate extract and deposits without any repetition of the name
stems.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: bbd87a3c03b1f173b1ed73a6d502c0196c18a72f.1467053537.git.alistair.francis@xilinx.com
[ EI Changes:
* Add Deposit macros
]
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add memory io handlers that glue the register API to the memory API.
Just translation functions at this stage. Although it does allow for
devices to be created without all-in-one mmio r/w handlers.
This patch also adds the RegisterInfoArray struct, which allows all of
the individual RegisterInfo structs to be grouped into a single memory
region.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: f7704d8ac6ac0f469ed35401f8151a38bd01468b.1467053537.git.alistair.francis@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This API provides some encapsulation of registers and factors out some
common functionality to common code. Bits of device state (usually MMIO
registers) often have all sorts of access restrictions and semantics
associated with them. This API allows you to define what those
restrictions are on a bit-by-bit basis.
Helper functions are then used to access the register which observe the
semantics defined by the RegisterAccessInfo struct.
Some features:
Bits can be marked as read_only (ro field)
Bits can be marked as write-1-clear (w1c field)
Bits can be marked as reserved (rsvd field)
Reset values can be defined (reset)
Bits can be marked clear on read (cor)
Pre and post action callbacks can be added to read and write ops
Verbose debugging info can be enabled/disabled
Useful for defining device register spaces in a data driven way. Cuts
down on a lot of the verbosity and repetition in the switch-case blocks
in the standard foo_mmio_read/write functions.
Also useful for automated generation of device models from hardware
design sources.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 40d62c7e1bf6e63bb4193ec46b15092a7d981e59.1467053537.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a macro that creates a 64bit value which has length number of ones
shifted across by the value of shift.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 9773244aa1c8c26b8b82cb261d8f5dd4b7b9fcf9.1467053537.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since QEMU performs cacheable accesses to guest memory when doing DMA
as part of the implementation of emulated PCI devices, guest drivers
should use cacheable accesses as well when running under KVM. Since this
essentially means that emulated PCI devices are DMA coherent, set the
'dma-coherent' DT property on the PCIe host controller DT node.
This brings the DT description into line with the ACPI description,
which already marks the PCI bridge as cache coherent (see commit
bc64b96c98).
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 1467134090-5099-1-git-send-email-ard.biesheuvel@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Starting QEMU with -S results in current_cpu containing its initial
value of NULL. It is however possible to connect to such QEMU instance
and query various CPU registers, one example being CPUID, and doing that
results in QEMU segfaulting.
Using qemu_get_cpu(0) seem reasonable enough given that ARMv7M
architecture is a single core architecture.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It doesn't make sense to pass a NULL ops argument to
memory_region_init_rom_device(), because the effect will
be that if the guest tries to write to the memory region
then QEMU will segfault. Catch the bug earlier by sanity
checking the arguments to this function, and remove the
misleading documentation that suggests that passing NULL
might be sensible.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1467122287-24974-4-git-send-email-peter.maydell@linaro.org
The imx boards were all incorrectly creating ROMs using
memory_region_init_rom_device() with a NULL ops pointer. This
will cause QEMU to abort if the guest tries to write to the
ROM. Switch to the new memory_region_init_rom() instead.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1467122287-24974-3-git-send-email-peter.maydell@linaro.org
Provide a new helper function memory_region_init_rom() for memory
regions which are read-only (and unlike those created by
memory_region_init_rom_device() don't have special behaviour
for writes). This has the same behaviour as calling
memory_region_init_ram() and then memory_region_set_readonly()
(which is what we do today in boards with pure ROMs) but is a
more easily discoverable API for the purpose.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1467122287-24974-2-git-send-email-peter.maydell@linaro.org
SYS_HEAPINFO is one of the few semihosting calls which has to write
values back into a parameter block in memory. When we added
support for 64-bit semihosting we updated the code which reads from
the parameter block to read 64-bit words but forgot to change the
code that writes back into the block. Update it to treat the
block as a set of words of the appropriate width for the guest.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1466783381-29506-3-git-send-email-peter.maydell@linaro.org
The fields in the TaskState heap_base, heap_limit and stack_base
are all guest addresses (representing the locations of the heap
and stack for the guest binary), so they should be abi_ulong
rather than uint32_t. (This only in practice affects ARM AArch64
since all the other semihosting implementations are 32-bit.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Message-id: 1466783381-29506-2-git-send-email-peter.maydell@linaro.org
This reverts commit 1f8828ef57.
Cc: qemu-stable@nongnu.org
Reported-by: Robin Geuze <robing@transip.nl>
Tested-by: Robin Geuze <robing@transip.nl>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
virtio migrates the low 32 feature bits twice, the first copy is there
for compatibility but ever since
019a3edbb2: ("virtio: make features 64bit
wide") it's ignored on load. This is wrong since virtio_net_load tests
self announcement and guest offloads before the second copy including
high feature bits is loaded. This means that self announcement, control
vq and guest offloads are all broken after migration.
Fix it up by loading low feature bits: somewhat ugly since high and low
bits become out of sync temporarily, but seems unavoidable for
compatibility. The right thing to do for new features is probably to
test the host features, anyway.
Fixes: 019a3edbb2
("virtio: make features 64bit wide")
Cc: qemu-stable@nongnu.org
Reported-by: Robin Geuze <robing@transip.nl>
Tested-by: Robin Geuze <robing@transip.nl>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The host notifier rework tried both to unify host notifiers across
transports and plug a possible hole during host notifier
re-assignment. Unfortunately, this meant a change in semantics that
breaks vhost and iSCSI+dataplane.
As the minimal fix, keep the common host notifier code but revert
to the old semantics so that we have time to figure out the proper
fix.
Fixes: 6798e245a3 ("virtio-bus: common ioeventfd infrastructure")
Reported-by: Peter Lieven <pl@kamp.de>
Reported-by: Jason Wang <jasowang@redhat.com>
Reported-by: Marc-André Lureau <marcandre.lureau@gmail.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Tested-by: Jason Wang <jasowang@redhat.com>
Tested-by: Peter Lieven <pl@kamp.de>
PcPciInfo has two (ill-named) members: Range w32 is the PCI hole, and
w64 is the PCI64 hole.
Three users:
* I440FXState and MCHPCIState have a member PcPciInfo pci_info, but
only pci_info.w32 is actually used. This is confusing. Replace by
Range pci_hole.
* acpi_build() uses auto PcPciInfo pci_info to forward both PCI holes
from acpi_get_pci_info() to build_dsdt(). Replace by two variables
Range pci_hole, pci_hole64. Rename acpi_get_pci_info() to
acpi_get_pci_holes().
PcPciInfo is now unused; drop it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Range pci_info.w32 records the location of the PCI hole.
It's initialized to empty when QOM zeroes I440FXState. That's a fine
value for a still unknown PCI hole.
i440fx_init() sets pci_info.w32.begin = below_4g_mem_size. Changes
the PCI hole from empty to [below_4g_mem_size, UINT64_MAX]. That's a
bogus value.
i440fx_pcihost_initfn() sets pci_info.end = IO_APIC_DEFAULT_ADDRESS.
Since i440fx_init() ran already, this changes the PCI hole to
[below_4g_mem_size, IO_APIC_DEFAULT_ADDRESS-1]. That's the correct
value.
Setting the bounds of the PCI hole in two separate places is
confusing, and begs the question whether the bogus intermediate value
could be used by something, or what would happen if we somehow managed
to realize an i440FX device without having run the board init function
i440fx_init() first.
Avoid the confusion by setting the (constant) upper bound along with
the lower bound in i440fx_init().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Since iommu devices can be created with '-device' there is
no need to keep iommu as machine and mch property.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use the standard '-device intel-iommu' to create the IOMMU device.
The legacy '-machine,iommu=on' can still be used.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Allow adding sysbus devices with -device on Q35.
At first Q35 will support only intel-iommu to be added this way,
however the command line will support all sysbus devices.
Mark with 'cannot_instantiate_with_device_add_yet' the ones
causing immediate problems (e.g. crashes).
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Skip bus_master_enable region creation on PCI device init
in order to be sure the IOMMU device (if present) would
be created in advance. Add this memory region at machine_done time.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Mac99's PCI root bus is not part of a host bridge,
realize it manually.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit "8156d48 pc: allow raising low memory via max-ram-below-4g
option" causes a regression on xen, because it uses a different
memory split.
This patch initializes max-ram-below-4g to zero and leaves the
initialization to the memory initialization functions. That way
they can pick different default values (max-ram-below-4g is zero
still) or use the user supplied value (max-ram-below-4g is non-zero).
Also skip the whole ram split calculation on Xen. xen_ram_init()
does its own split calculation anyway so it is superfluous, also
this way xen_ram_init can actually see whenever max-ram-below-4g
is zero or not.
Reported-by: Anthony PERARD <anthony.perard@citrix.com>
Tested-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently the internal hash code is using the gnutls hash APIs.
GNUTLS in turn is wrapping either nettle or gcrypt. Not only
were the GNUTLS hash APIs not added until GNUTLS 2.9.10, but
they don't expose support for all the algorithms QEMU needs
to use with LUKS.
Address this by directly wrapping nettle/gcrypt in QEMU and
avoiding GNUTLS's extra layer of indirection. This gives us
support for hash functions on a much wider range of platforms
and opens up ability to support more hash functions. It also
avoids a GNUTLS bug which would not correctly handle hashing
of large data blocks if int != size_t.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
On MinGW one of the system headers already has "OUT" defined
which causes a compile failure of the test suite. Rename the
test suite var to 'out' to avoid this clash
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
When opening an existing LUKS volume, if the iv generator is
essiv, then the iv hash algorithm is mandatory to provide. We
must report an error if it is omitted in the cipher mode spec,
not silently default to hash 0 (md5). If the iv generator is
not essiv, then we explicitly ignore any iv hash algorithm,
rather than report an error, for compatibility with dm-crypt.
When creating a new LUKS volume, if the iv generator is essiv
and no iv hsah algorithm is provided, we should default to
using the sha256 hash.
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
This commit adds a fast variant of SeaBIOS called 'bios-fast.bin'.
It's designed to be the fastest (also the smallest, but that's not the
main aim) SeaBIOS that is just enough to boot a Linux kernel using the
-kernel option on i686 and x86_64.
This commit does not modify the -kernel option to use this. You have
to specify it by doing something like this:
-kernel vmlinuz -bios bios-fast.bin
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
git shortlog
============
Alex Williamson (1):
fw/pci: Add support for mapping Intel IGD via QEMU
Haozhong Zhang (1):
fw/msr_feature_control: add support to set MSR_IA32_FEATURE_CONTROL
Kevin O'Connor (1):
build: fix .text section address alignment
Marcel Apfelbaum (1):
fw/pci: add Q35 S3 support
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Provide basic support for stateless DHCPv6 (see RFC 3736) so
that guests can also automatically boot via IPv6 with SLIRP
(for IPv6 network booting, see RFC 5970 for details).
Tested with:
qemu-system-ppc64 -nographic -vga none -boot n -net nic \
-net user,ipv6=yes,ipv4=no,tftp=/path/to/tftp,bootfile=ppc64.img
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Commit fad7fb9ccd ("Add IPv6 support to the TFTP code")
refactored some common code for preparing the mbuf into a new
function called tftp_prep_mbuf_data(). One part of this common
code is to do a "memset(m->m_data, 0, m->m_size);" for the related
buffer first. However, at two spots, the memset() was not removed
from the calling function, so it currently done twice in these code
paths. Thus let's delete these superfluous memsets in the calling
functions now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
This adds the RDNSS option to IPv6 router advertisements, so that the guest
can autoconfigure the DNS server address.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
---
Changes since last submission:
- Disable on windows, until we have support for it
They look like fe80::%eth0
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
---
Changes since last submission:
- fix windows build
This makes get_dns_addr address family-agnostic, thus allowing to add the
IPv6 case.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Separate get_dns_addr into get_dns_addr_cached and get_dns_addr_resolv_conf
to make conversion to IPv6 easier.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAld2ZGoACgkQAvw66wEB28LbNQCfbKhlgcwRvD/F1B5IFQErRkLf
rBsAnR5QQhl8eJK+Dfdiy4H/mjKuXHyN
=6o/q
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/gkurz/tags/for-upstream' into staging
Only trivial fixes.
# gpg: Signature made Fri 01 Jul 2016 13:39:06 BST
# gpg: using DSA key 0x02FC3AEB0101DBC2
# gpg: Good signature from "Greg Kurz <gkurz@fr.ibm.com>"
# gpg: aka "Greg Kurz <groug@free.fr>"
# gpg: aka "Greg Kurz <gkurz@linux.vnet.ibm.com>"
# gpg: aka "Gregory Kurz (Groug) <groug@free.fr>"
# gpg: aka "Gregory Kurz (Cimai Technology) <gkurz@cimai.com>"
# gpg: aka "Gregory Kurz (Meiosys Technology) <gkurz@meiosys.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 2BD4 3B44 535E C0A7 9894 DBA2 02FC 3AEB 0101 DBC2
* remotes/gkurz/tags/for-upstream:
9p: synth: drop v9fs_ prefix
9p: don't include <sys/uio.h>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
