From time to time, there are issues with ioapic, either on guest side or
on hypervisor side. Good to have some persistent traces for better
triaging and debugging.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1483952153-7221-2-git-send-email-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The GICv3 requires that we only signal Pending interrupts to
the CPU. This category does not include Pending+Active interrupts,
which means we need to check whether the interrupt is Active in
the gicr_int_pending() and gicd_int_pending() functions.
Interrupts are rarely in the Active+Pending state, but KVM
uses this as part of its handling of the virtual timer, so
this bug was causing KVM to go into an infinite loop of
taking the vtimer interrupt when the guest first triggered it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
In the ARMCPRegInfo definitions for the GICv3 CPU interface
registers, we were trying to use .fieldoffset to specify
the locations of data fields within the GICv3CPUState struct.
This is completely broken, because .fieldoffset is for offsets
into the CPUARMState struct. We didn't notice because we
were only using this for reads to BPR0, AP0R<n>, IGRPEN0
and CTLR_EL3, and Linux doesn't use these registers.
Replace the .fieldoffset uses with explicit read functions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 20161209143703.29457-1-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We've currently got 18 architectures in QEMU, and thus 18 target-xxx
folders in the root folder of the QEMU source tree. More architectures
(e.g. RISC-V, AVR) are likely to be included soon, too, so the main
folder of the QEMU sources slowly gets quite overcrowded with the
target-xxx folders.
To disburden the main folder a little bit, let's move the target-xxx
folders into a dedicated target/ folder, so that target-xxx/ simply
becomes target/xxx/ instead.
Acked-by: Laurent Vivier <laurent@vivier.eu> [m68k part]
Acked-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de> [tricore part]
Acked-by: Michael Walle <michael@walle.cc> [lm32 part]
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com> [s390x part]
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> [s390x part]
Acked-by: Eduardo Habkost <ehabkost@redhat.com> [i386 part]
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com> [sparc part]
Acked-by: Richard Henderson <rth@twiddle.net> [alpha part]
Acked-by: Max Filippov <jcmvbkbc@gmail.com> [xtensa part]
Reviewed-by: David Gibson <david@gibson.dropbear.id.au> [ppc part]
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> [crisµblaze part]
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn> [unicore32 part]
Signed-off-by: Thomas Huth <thuth@redhat.com>
According to ARM DUI 0552A 4.2.10. NVIC set pending status
also for disabled interrupts. Correct the logic for
when interrupts are marked pending both on input level
transition and when interrupts are dismissed, to match
the NVIC behaviour rather than the 11MPCore GIC.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently the device tree node for the XICS interrupt controller is in
spapr_create_fdt_skel(). As part of consolidating device tree construction
to reset time, this moves it to a function called from spapr_build_fdt().
In addition we move the actual code into hw/intc/xics_spapr.c with the
rest of the PAPR specific interrupt controller code.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
The routines :
void icp_set_cppr(ICPState *icp, uint8_t cppr);
void icp_set_mfrr(ICPState *icp, uint8_t mfrr);
void icp_eoi(ICPState *icp, uint32_t xirr);
now use one 'ICPState *icp' argument instead of a 'XICSState *' and a
server arguments. The backlink on XICSState* is used whenever needed.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The link will be used to change the API of the icp_* routines which
are still using an XICSState as an argument.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
xics_spapr and xics_kvm nearly define the same 'set_nr_servers'
handler. Only the type of the ICP differs. So let's make a common one
to remove some duplicated code.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Useful to debug interrupt problems.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[clg: - updated for qemu-2.7
- added a test on ->irqs as it is not necessarily allocated
(PHB3_MSI)
- removed static variable g_xics and replace with a loop on all
children to find the xics objects.
- rebased on InterruptStatsProvider interface ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
SDM: x2APIC State Transitions:
State Changes From xAPIC Mode to x2APIC Mode
"
Any APIC ID value written to the memory-mapped
local APIC ID register is not preserved
"
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
APIC ID should be restored to initial APIC ID
state after Reset and Power-On.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
ACPI ID is 32 bit wide on CPUs with x2APIC support.
Extend 'id' property to support it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Fix some problems with the tracepoints for ICC register reads
and writes:
* tracepoints for ICC_BPR<n>, ICC_AP<n>R<x>, ICC_IGRPEN<n>,
ICC_EIOR<n> were not printing the <n> that indicated whether
the access was to the group 0 or 1 register
* the ICC_IGREPEN1_EL3 read function was not actually calling
the associated tracepoint
* the ICC_BPR<n> write function was incorrectly calling the
tracepoint for ICC_PMR writes
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1476294876-12340-4-git-send-email-peter.maydell@linaro.org
Remove unused debugging code to fix native building on aarch64. Without
this change, the following -Werr output inhibits make from completing.
qemu/hw/intc/arm_gic_kvm.c:38:18: error: debug_gic_kvm defined but not used [-Werror=unused-const-variable=]
static const int debug_gic_kvm = 0;
^~~~~~~~~~~~~
cc1: all warnings being treated as errors
qemu/rules.mak:60: recipe for target 'hw/intc/arm_gic_kvm.o' failed
make[1]: *** [hw/intc/arm_gic_kvm.o] Error 1
Makefile:205: recipe for target 'subdir-aarch64-softmmu' failed
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20161011163202.19720-1-cov@codeaurora.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The MMIO based interface to APIC doesn't work well with MSIs that have
upper address bits set (remapped x2APIC MSIs). A specialized interface
is a quick and dirty way to avoid the shortcoming.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Every configuration has only up to one APIC class and we'll be extending
the class with a function that can be called without an instanced
object, so a direct access to the class is convenient.
This patch will break compilation if some code uses apic_get_class()
with CONFIG_USER_ONLY.
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The existing implementation remains same and ics-base is introduced. The
type name "ics" is retained, and all the related functions renamed as
ics_simple_*
This will allow different implementations for the source controllers
such as the MSI support of PHB3 on Power8 which uses in-memory state
tables for example.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[ clg: added ICS_BASE_GET_CLASS and related fixes, based on :
http://patchwork.ozlabs.org/patch/646010/ ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Instead of an array of fixed sized blocks, use a list, as we will need
to have sources with variable number of interrupts. SPAPR only uses
a single entry. Native will create more. If performance becomes an
issue we can add some hashed lookup but for now this will do fine.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[ move the initialization of list to xics_common_initfn,
restore xirr_owner after migration and move restoring to
icp_post_load]
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
[ clg: removed the icp_post_load() changes from nikunj patchset v3:
http://patchwork.ozlabs.org/patch/646008/ ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ITS control frame is in-kernel emulated while accesses to the
GITS_TRANSLATER are mediated through the KVM_SIGNAL_MSI ioctl (MSI
direct MSI injection advertised by the CAP_SIGNAL_MSI capability)
the kvm_gsi_direct_mapping is explicitly set to false to emphasize the
difference with GICv2M. Direct mapping cannot work with ITS since
the content of the MSI data is not the target interrupt ID but an
eventd id.
GSI routing is advertised (kvm_gsi_routing_allowed) as well as
msi/irqfd signaling (kvm_msi_via_irqfd_allowed).
The MSI frame (GITS_TRANSLATER) absolute GPA is computed on first
kvm_its_send_msi() call. It is then passed through KVM_SIGNAL_MSI
ioctl.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1474616617-366-6-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is the basic skeleton for both KVM and software-emulated ITS.
Since we already prepare status structure, we also introduce complete
VMState description. But, because we currently have no migratable
implementations, we also set unmigratable flag.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1474616617-366-3-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Advertise gsi routing and set up irqchip routing entries for
GIC SPIs.
This is not mandated as long as MSI routing is not used
(because the kernel sets a default irqchip routing table).
However once MSI routing gets used (for VIRTIO-PCI vhost for
example), the first call to KVM_SET_GSI_ROUTING overrides the
kernel default irqchip table.
If no routing entry exists for the GSI, any IRQFD signaling for
this GSI will fail.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1474616617-366-2-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We have to change the vmstate version due to changes in statistics counters.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <1474921408-24710-5-git-send-email-hpoussin@reactos.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This interface will be used by HMP commands 'info irq' and 'info pic'.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <1474921408-24710-2-git-send-email-hpoussin@reactos.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's 2.8 now, and maybe it's time to switch IOAPIC default version to
0x20.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1474608795-23058-1-git-send-email-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fix inconsistent irq status, because of this in the trace logs, for e.g.
LSI status was 0x7, i.e. XICS_STATUS_ASSERTED, XICS_STATUS_SENT and
XICS_STATUS_REJECTED all set, which did not make sense. So the REJECTED
would have been set in earlier interrupt cycle, and then asserted and
sent in this current one.
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Introduce a new APIC macro to replace APIC_COMMON macro in
hw/intc/apic.c in order to capture access LAPIC in qemu
even if LAPIC is emulated in kvm.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Message-Id: <1473923759-13912-1-git-send-email-wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We abort a few lines above if kernel_xics_fd == -1.
This is only code cleanup.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Some old Linux kernels (upstream before v4.0), or any released RHEL
kernels has problem in sending APIC EOI when IR is enabled. Meanwhile,
many of them only support explicit EOI for IOAPIC, which is only
introduced in IOAPIC version 0x20. This patch provide a way to boost
QEMU IOAPIC to version 0x20, in order for QEMU to correctly receive EOI
messages.
Without boosting IOAPIC version to 0x20, kernels before commit d32932d
("x86/irq: Convert IOAPIC to use hierarchical irqdomain interfaces")
will have trouble enabling both IR and level-triggered interrupt devices
(like e1000).
To upgrade IOAPIC to version 0x20, we need to specify:
-global ioapic.version=0x20
To be compatible with old systems, 0x11 will still be the default IOAPIC
version. Here 0x11 and 0x20 are the only versions to be supported.
One thing to mention: this patch only applies to emulated IOAPIC. It
does not affect kernel IOAPIC behavior.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1470059959-372-1-git-send-email-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For level triggered interrupts, we will get Remote IRR bit cleared after
guest kernel finished processing specific request. Before that, we
should ignore the same interrupt from triggering again.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1469974685-4144-1-git-send-email-peterx@redhat.com>
[Push new "if" up so that it covers KVM split irqchip as well. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- interrupt remapping for intel iommus
- a bunch of virtio cleanups
- fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXkQsqAAoJECgfDbjSjVRpanoIAJ9JVlc1aEjt9sa0cSBcs+NQ
J7JmgU9FqFsj+4FrNTouO3AxTjHurd1UAULP1WMPD+V3JpbnHct8r6SCBLQ5EBMN
VOjYo4DwWs1g+DqnQ9WZmbadu06XvYi/yiAKNUzWfZk0MR11D0D/S5hmarNKw0Kq
tGHeTWjGeY4WqFLV7m+qB4+cqkAByn6um99UtUvgLL05RgIEIP2IEMKYZ+rXvAa9
iGUvzqlO7mbq/+LbL18kaWywa4TCwbbd2eSGWaqhX4CuB62Rl33mWTXFcfaYhkyp
Z3FgwaJ09h0lAjSVEbyAuLFMfO/BnMcsoKqwl4xc4vkn/xBCqFtgH9JcEVm3O8U=
=ge2D
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc, pci, virtio: new features, cleanups, fixes
- interrupt remapping for intel iommus
- a bunch of virtio cleanups
- fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 21 Jul 2016 18:49:30 BST
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (57 commits)
intel_iommu: avoid unnamed fields
virtio: Update migration docs
virtio-gpu: Wrap in vmstate
virtio-gpu: Use migrate_add_blocker for virgl migration blocking
virtio-input: Wrap in vmstate
9pfs: Wrap in vmstate
virtio-serial: Wrap in vmstate
virtio-net: Wrap in vmstate
virtio-balloon: Wrap in vmstate
virtio-rng: Wrap in vmstate
virtio-blk: Wrap in vmstate
virtio-scsi: Wrap in vmstate
virtio: Migration helper function and macro
virtio-serial: Remove old migration version support
virtio-net: Remove old migration version support
virtio-scsi: Replace HandleOutput typedef
Revert "mirror: Workaround for unexpected iohandler events during completion"
virtio-scsi: Call virtio_add_queue_aio
virtio-blk: Call virtio_add_queue_aio
virtio: Introduce virtio_add_queue_aio
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let IOAPIC the first consumer of x86 IOMMU IEC invalidation
notifiers. This is only used for split irqchip case, when vIOMMU
receives IR invalidation requests, IOAPIC will be notified to update
kernel irq routes. For simplicity, we just update all IOAPIC routes,
even if the invalidated entries are not IOAPIC ones.
Since now we are creating IOMMUs using "-device" parameter, IOMMU
device will be created after IOAPIC. We need to do the registration
after machine done by leveraging machine_done notifier.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Abstract IOAPIC entry parsing logic into a helper function.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch translates all IOAPIC interrupts into MSI ones. One pseudo
ioapic address space is added to transfer the MSI message. By default,
it will be system memory address space. When IR is enabled, it will be
IOMMU address space.
Currently, only emulated IOAPIC is supported.
Idea suggested by Jan Kiszka and Rita Sinha in the following patch:
https://lists.gnu.org/archive/html/qemu-devel/2016-03/msg01933.html
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
instance_id is generated by last_used_id + 1 for a given device type
so for QEMU with 3 CPUs instance_id for APICs is a seti of [0, 1, 2]
When CPU in the middle is hot-removed and migration started
APICs with instance_ids 0 and 2 are transferred in migration stream.
However target starts with 2 CPUs and APICs' instance_ids are
generated from scratch [0, 1] hence migration fails with error
Unknown savevm section or instance 'apic' 2
Fix issue by manually registering APIC's vmsd with apic_id as
instance_id, in this case instance_id on target will always
match instance_id on source as apic_id is the same for a given
cpu instance.
Reported-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Callbacks will do necessary cleanups before APIC device is deleted
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
local_apics[] is sized to contain all APIC ID supported in xAPIC mode,
so use APIC ID as index in it instead of constantly increasing counter idx.
Fixes error "apic initialization failed" when a CPU hotplugged and
unplugged more times than there are free slots in local_apics[].
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
MAX_APICS is only used by child 'apic' class and not
by its parent TYPE_APIC_COMMON or any other derived
class.
Move check into end user 'apic' class so it won't
get in the way of other APIC implementations
if they support more then MAX_APICS.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Coverity complains that the GICR_IPRIORITYR case in gicv3_readl()
can overflow an array, because it doesn't know that the offsets
passed to that function must be word aligned. Add some assert()s
which hopefully tell Coverity that this isn't possible.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1468261372-17508-1-git-send-email-peter.maydell@linaro.org
Changes:
* support 10-bit ASIDs
* MIPS64R6-generic renamed to I6400
* initial GIC support
* implement RESET_BASE register in CM GCR
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJXhMtOAAoJEFIRjjwLKdprahQH/2qBMp7Hnucy7jhiPHRtRZTo
zZAhuRJ0Z2LT9xH+sTg3HcjHI7aXps5cG2f7Fw4X/JKNRY4KO19yEBnMhc5he2Ut
XPtHCeMXXq6zU4RMHqlx6wChHn5AUll/3EeSvm6JMV+HhE6oDBk1yl5C8ipPlVCd
KEz6LlUFNMbuxu2tM4DoMNAWeKmunBx3vO+JuErB6hjCWM5G0mV9aPDkbwTOmVLn
qGgzzmNDiPE6JWrSpbHetsdCO7V9xtXzhcFsu240GJ/+XJMjUXb1m6ETsJxT9EYh
vLfFzwozBSjX6ZQZVNFIAeJZnq96NOHqZ56sU7s4YktVXjl26JAahScTTH0aiNo=
=sTce
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/lalrae/tags/mips-20160712' into staging
MIPS patches 2016-07-12
Changes:
* support 10-bit ASIDs
* MIPS64R6-generic renamed to I6400
* initial GIC support
* implement RESET_BASE register in CM GCR
# gpg: Signature made Tue 12 Jul 2016 11:49:50 BST
# gpg: using RSA key 0x52118E3C0B29DA6B
# gpg: Good signature from "Leon Alrae <leon.alrae@imgtec.com>"
# Primary key fingerprint: 8DD3 2F98 5495 9D66 35D4 4FC0 5211 8E3C 0B29 DA6B
* remotes/lalrae/tags/mips-20160712:
target-mips: enable 10-bit ASIDs in I6400 CPU
target-mips: support CP0.Config4.AE bit
target-mips: change ASID type to hold more than 8 bits
target-mips: add ASID mask field and replace magic values
target-mips: replace MIPS64R6-generic with the real I6400 CPU model
hw/mips_cmgcr: implement RESET_BASE register in CM GCR
hw/mips_cpc: make VP correctly start from the reset vector
target-mips: add exception base to MIPS CPU
hw/mips/cps: create GIC block inside CPS
hw/mips: implement Global Interrupt Controller
hw/mips: implement GIC Interval Timer
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
