Open-code functions created in the previous patch,
to make code more compact and clear.
Detcted and documented what looks like a bug in code
that becomes apparent from this refactoring.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Added some TODOs: they are trivial but omitted here
to make the patch logic as transparent as possible.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch implements helper functions for pcie aer capability
which will be used later.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch adds W1C bit support in the initialization/reset of pci
status registers.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Errors should be logged using error_report() so they go to the
appropriate monitor.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
As pointed out by avi the vgabios update is guest-visible and thus has
migration implications.
One change is that the vga has a valid pci rom bar now. We already have
a pci bus property to enable/disable the rom bar and we'll load the bios
via fw_cfg as fallback for the no-rom-bar case. So we just have to add
compat properties to handle this case.
A second change is that the magic bochs lfb @ 0xe0000000 is gone. When
live-migrating a guest from a older qemu version it might be using the
lfb though, so we have to keep it for the old machine types. The patch
enables the bochs lfb in case we don't have the pci rom bar enabled
(i.e. we are in 0.13+older compat mode).
This patch depends on these patches which add (and use) the pc-0.13
machine type:
http://patchwork.ozlabs.org/patch/70797/http://patchwork.ozlabs.org/patch/70798/
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: avi@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
While not explicitly stated in the spec, it was observed on real systems
that enabling loopback testing on the pcnet controller disables
reception of external frames. And some legacy software relies on it, so
provide this behavior.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch enables MSI-X for virtfs-9p-pci. It also adds a
compat property to pc-0.13 which turns it of there to stay
compatible to 0.13-stable.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
We have an OS which writes to port 0x400 when probing for special hardware.
This causes an exit of the VM. With SeaBIOS this port isn't used anyway.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-By: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Bernhard Kohl <bernhard.kohl@nsn.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
We can't let the compiler define the alignment for qemu_cfg data.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds missing braces around if/else statements that call
macros which are likely to result in errors if the macro is
changed. It also makes the code comply better with CODING_STYLE.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
A via -kernel supplied x86_64 ELF image is being started in 32bit mode.
Detect and exit if a 64bit image has been supplied.
Signed-off-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
local_apics are allocated sequentially and never removed, so
we can stop any iterations that go to MAX_APICS as soon as we
hit the first NULL. Looking at a small guest running a virtio-net
workload with oprofile, this drops apic_get_delivery_bitmask()
from #3 in the profile to down in the noise.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch fixes hot unplug of cold plugged devices
(those present at system start), which got broken by
5beb8ad503 .
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cam Macdonell <cam@cs.ualberta.ca>
Tested-by: Cam Macdonell <cam@cs.ualberta.ca>
Reported-by: Cam Macdonell <cam@cs.ualberta.ca>.
pcibus_dev_print() was erroneously retrieving the device bus
number from the secondary bus number offset of the device
instead of the bridge above the device. This ends of landing
in the 2nd byte of the 3rd BAR for devices, which thankfully
is usually zero.
Note: pcibus_get_dev_path() copied this code,
inheriting the same bug. pcibus_get_dev_path() is used for
ramblock naming, so changing it can effect migration. However,
I've only seen this byte be non-zero for an assigned device,
which can't migrate anyway, so hopefully we won't run into
any issues.
This patch does not touch pcibus_get_dev_path, as
bus number is guest assigned for nested buses,
so using it for migration is broken anyway.
Fix it properly later.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When adding the length to the pseudo header, we're not properly
accounting for overflow.
From: Mark Wu <dwu@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Make stdvga provide the new vgabios binary (with pcibios support)
using the PCI option rom bar. Seabios will happily load it from
there. The new vga bios will also lookup the framebuffer address
in pci config space, so the magic bochs lfb @ 0xe0000000 is not
needed any more -> zap it.
Without the patch:
# dmesg | grep framebuffer
vesafb: framebuffer at 0xe0000000, mapped to 0xf7e80000, using 1875k, total 8192k
# lspci -vs2
00:02.0 VGA compatible controller: Technical Corp. Device 1111 (prog-if 00 [VGA controller])
Subsystem: Qumranet, Inc. Device 1100
Physical Slot: 2
Flags: fast devsel
Memory at f0000000 (32-bit, prefetchable) [size=8M]
Expansion ROM at <unassigned> [disabled]
With patch applied:
# dmesg | grep framebuffer
vesafb: framebuffer at 0xf0000000, mapped to 0xf7e80000, using 1875k, total 8192k
# lspci -vs2
00:02.0 VGA compatible controller: Technical Corp. Device 1111 (prog-if 00 [VGA controller])
Subsystem: Qumranet, Inc. Device 1100
Physical Slot: 2
Flags: fast devsel
Memory at f0000000 (32-bit, prefetchable) [size=8M]
Expansion ROM at f0800000 [disabled] [size=64K]
cheers,
Gerd
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch fixes hot unplug of cold plugged devices
(those present at system start), which got broken by
5beb8ad503 .
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cam Macdonell <cam@cs.ualberta.ca>
Tested-by: Cam Macdonell <cam@cs.ualberta.ca>
Reported-by: Cam Macdonell <cam@cs.ualberta.ca>.
pcibus_dev_print() was erroneously retrieving the device bus
number from the secondary bus number offset of the device
instead of the bridge above the device. This ends of landing
in the 2nd byte of the 3rd BAR for devices, which thankfully
is usually zero.
Note: pcibus_get_dev_path() copied this code,
inheriting the same bug. pcibus_get_dev_path() is used for
ramblock naming, so changing it can effect migration. However,
I've only seen this byte be non-zero for an assigned device,
which can't migrate anyway, so hopefully we won't run into
any issues.
This patch does not touch pcibus_get_dev_path, as
bus number is guest assigned for nested buses,
so using it for migration is broken anyway.
Fix it properly later.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When adding the length to the pseudo header, we're not properly
accounting for overflow.
From: Mark Wu <dwu@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The HDA bus supports up to 15 codecs, with addresses 0 ... 14.
We get that wrong in two places:
* When handing out addresses we accept address 15 as valid.
* The bitmasks for two registers (WAKEEN and STATESTS) don't
have bit 14 set.
This patch fixes it.
[ v2: codestyle: add braces ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: malc <av1474@comtv.ru>
The HDA bus supports up to 15 codecs, with addresses 0 ... 14.
We get that wrong in two places:
* When handing out addresses we accept address 15 as valid.
* The bitmasks for two registers (WAKEEN and STATESTS) don't
have bit 14 set.
This patch fixes it.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: malc <av1474@comtv.ru>
This patch adds MSI support to the intel hda audio driver. It is
enabled by default, use '-device intel-hda,msi=0' to disable it.
[ v2: codestyle: add braces ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: malc <av1474@comtv.ru>
When the guest updates the WAKEEN register we
must re-calculate the IRQ status.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: malc <av1474@comtv.ru>
HDA: Honor WAKEEN bits when deciding to raise an interrupt on codec
status change. This prevents an interrupt storm with the Haiku HDA
driver which does not handle codec status changes in the irq handler.
Signed-off-by: François Revol <revol@free.fr>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: malc <av1474@comtv.ru>
Add pci exit callback for the intel-hda device and cleanup properly.
Also add an exit callback to the HDA bus implementation and make sure
it is called on qdev_free().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: malc <av1474@comtv.ru>
Fix scsi-disk to use the usual completion paths that involve rerror/werror
handling instead of directly completing the requests in cases where
bdrv_aio_readv/writev returns NULL.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Fix virtio-blk to use the usual completion path that involves werror handling
instead of directly completing the request in cases where bdrv_aio_flush
returns NULL.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This pulls the request completion for error cases from the caller to
scsi_disk_emulate_command. This should not change semantics, but allows to
reuse scsi_handle_write_error() for flushes in the next patch.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
This implements the rerror option for SCSI disks.
It also includes minor changes to the write path where the same code is used
that was criticized in the review for the changes to the read path required for
rerror support.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
This patch adds three devices to qemu:
intel-hda
Intel HD Audio Controller, the PCI device. Provides a HDA bus.
Emulates ICH6 at the moment. Adding a ICH9 PCIE
variant shouldn't be hard.
hda-duplex
HDA Codec. Attaches to the HDA bus. Supports 16bit stereo,
rates 16k -> 96k, playback, recording and volume control
(with CONFIG_MIXEMU=y).
hda-output
HDA Codec without recording support. Subset of the hda-duplex
codec. Use this if you don't want your guests access your mic.
Usage: add '-device intel-hda -device hda-duplex' to your command line.
Tested guests:
* Linux works.
* Win7 works.
* DOS (mpxplay) works.
* WinXP doesn't work.
[ v2 changes ]
* Fixed endianess, big endian hosts work now.
* Fixed some emulation bugs.
* Added immediate command emulation.
* Added vmstate support.
* Make it behave like all other sound card drivers:
- can be configured via '--audio-card-list=hda'
- can be added to a VM using '-soundhw hda'
* Code style fixups.
* Zapped guest-triggerable asserts.
* Handle partial reads/writes of audio data correctly.
Cc: malc <av1474@comtv.ru>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: malc <av1474@comtv.ru>
TRUE/FALSE are generally reserved keywords and shouldn't be defined in
a driver like this. Rename the macros to SDP_TRUE and SDP_FALSE
respectively.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
config write handlers should be idempotent.
So no need for complex range checks: a simple
one checking that we are touching the relevant capability
will do.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
- save/restore must not check w1c bits
since they are in fact guest controlled
- clear w1c bits on reset
Note: for express there are different kinds of
reset, some leave part of config space alone.
We will likely need a sticky bit mask to implement this.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Simplify logic for hotplug notification, by tracking state of the
logical interrupt condition. We then simply use this variable to make
the interrupt decision, according to spec.
API is made cleaner as we no longer force users to pass in
old slot control value.
Includes fixes by Isaku Yamahata.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Simplify code slighly by reversing the polarity
for the range check
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Extract range functions from pci.h. These will be used by later patches
by non-PCI devices. Adjust current users.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
(cherry picked from commit bf1b007123)
Checking available index upon load instead of
only when vm is running makes is easier to
debug failures.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move timer init functions to a new file, qemu-timer-common.c. Make other
critical timer functions inlined to preserve performance in
qemu-timer.c, also move muldiv64() (used by the inline functions)
to qemu-timer.h.
Adjust block/raw-posix.c and simpletrace.c to use get_clock() directly.
Remove a similar/duplicate definition in qemu-tool.c.
Adjust hw/omap_clk.c to include qemu-timer.h because muldiv64() is used
there.
After this change, tracing can be used also for user code and
simpletrace on Win32.
Cc: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Acked-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
RAM registration used incorrect offset.
Fix by using the offset obtained previously for this purpose.
Spotted by GCC 4.6.0 20100925 warning, which is also avoided.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The werror option now affects not only write requests, but also flush requests.
Previously, it was not possible to stop a VM on a failed flush.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of always assuming success for bdrv_aio_flush, actually do something
with the error. This respects the werror option and accordingly ignores the
error, reports it to the guest or stops the VM and retries after cont.
Ignoring the error is trivial, obviously. For stopping the VM and retrying
later old code can be reused, but we need to introduce a new status for "retry
a flush". For reporting to the guest, fortunately the same action is required
as for a failed read/write (status = DRDY | ERR, error = ABRT), so this code
can be reused as well.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
ATA does not only have the WCACHE enabled bit in identify word 85, but also
a WCACHE supported bit in word 82. While the Linux kernel is fine with the
latter at least hdparm also needs the former before correctly displaying
the cache settings. There's also a non-zero chance other operating systems
are more picky in their volatile write cache detection.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add qemu_activate_mouse_event_handler() calls to the usb wavom tablet so
it actually receives events. Also make sure we only remove the handler
if we registered it before.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch updates the vmmouse handler registration and activation.
Old behavior:
vmmouse_read_id, vmmouse_request_relative and vmmouse_request_absolute
unregister the handler and re-register it.
New behavior:
vmmouse_request_relative and vmmouse_request_absolute will unregister
the handler in case the mode did change. Then register and active the
handler with current mode if needed.
Note that the old code never ever *activates* the handler, so the
vmmouse doesn't receive events. This trips up Fedora 14 for example:
Boot a default install without usb tablet, watch the X-Server activating
the vmmouse then, enjoy a non-functional mouse.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
readv & writev, read & write respectively from the current offset
of the file & hence their use has to be preceeded by a call to lseek.
preadv/writev can be used instead, as they take the offset as an argument.
This saves one system call( lseek ).
In case preadv is not supported, it is implemented by an lseek
followed by a readv. Depending upon the configuration of QEMU, the
appropriate read & write methods are selected. This patch also fixes the
zero byte read/write bug & obviates the need to apply a fix for that bug separately.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Sanchit Garg <sancgarg@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
We would need this to make sure we handle the mapped
security model correctly for different xattr names.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
The O_DIRECT flag imposes alignment restrictions on the length and address
of userspace buffers and the file offset of I/Os.
While VirtFS/9P has plans to implement O_DIRECT behavior on the server,
for now we will stick to a behavior like NFS by bypassing the page cache
only on the client. Server may still cache the I/O.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Synopsis
size[4] TReadlink tag[2] fid[4]
size[4] RReadlink tag[2] target[s]
Description
Readlink is used to return the contents of the symoblic link
referred by fid. Contents of symboic link is returned as a
response.
target[s] - Contents of the symbolic link referred by fid.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
SYNOPSIS
size[4] Tfsync tag[2] fid[4]
size[4] Rfsync tag[2]
DESCRIPTION
The Tfsync transaction transfers ("flushes") all modified in-core data of
file identified by fid to the disk device (or other permanent storage
device) where that file resides.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Synopsis
size[4] TGetlock tag[2] fid[4] getlock[n]
size[4] RGetlock tag[2] getlock[n]
Description
TGetlock is used to test for the existence of byte range posix locks on
a file identified by given fid. The reply contains getlock structure. If
the lock could be placed it returns F_UNLCK in type field of getlock structure.
Otherwise it returns the details of the conflicting locks in the getlock
structure
getlock structure:
type[1] - Type of lock: F_RDLCK, F_WRLCK
start[8] - Starting offset for lock
length[8] - Number of bytes to lock
If length is 0, lock all bytes starting at the location
'start' through to the end of file
proc_id[4] - process id that wants to take lock/owns the task
in case of reply
client[4] - Client id of the system that owns the process
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Synopsis
size[4] TLock tag[2] fid[4] flock[n]
size[4] RLock tag[2] status[1]
Description
Tlock is used to acquire/release byte range posix locks on a file
identified by given fid. The reply contains status of the lock request
flock structure:
type[1] - Type of lock: F_RDLCK, F_WRLCK, F_UNLCK
flags[4] - Flags could be either of
P9_LOCK_FLAGS_BLOCK(1) - Blocked lock request, if there is a
conflicting lock exists, wait for that lock to be released.
P9_LOCK_FLAGS_RECLAIM(2) - Reclaim lock request, used when client is
trying to reclaim a lock after a server restrart (due to crash)
start[8] - Starting offset for lock
length[8] - Number of bytes to lock
If length is 0, lock all bytes starting at the location 'start'
through to the end of file
pid[4] - PID of the process that wants to take lock
client_id[4] - Unique client id
status[1] - Status of the lock request, can be
P9_LOCK_SUCCESS(0), P9_LOCK_BLOCKED(1), P9_LOCK_ERROR(2) or
P9_LOCK_GRACE(3)
P9_LOCK_SUCCESS - Request was successful
P9_LOCK_BLOCKED - A conflicting lock is held by another process
P9_LOCK_ERROR - Error while processing the lock request
P9_LOCK_GRACE - Server is in grace period, it can't accept new lock
requests in this period (except locks with
P9_LOCK_FLAGS_RECLAIM flag set)
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
When 9P server fails to create a file due to permission problems it should
return EPERM. However the current 9P2000.L code returns EBADF. EBADF is NOT
a valid return value from open() call.
The problem is because we do not preserve the errno variable properly. If the
file open had failed, the call to close() on the fd in v9fs_post_lcreate()
fails and sets errno to EBADF. We should preserve the errno that we got from
open() and we should call close() only if we had a valid fd.
Signed-off-by: Sripathi Kodi <sripathik@in.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Replace debug printf statements with tracepoints.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Implement TI x3130 pcie downstream port switch.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Implement TI x3130 pcie upstream port switch.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Implements pcie root port switch in intel X58 ioh
whose device id is 0x3420.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
define struct PCIEPort which represents common part
of pci express port.(root, upstream and downstream.)
add a helper function for pcie port which can be used commonly by
root/upstream/downstream port.
define struct PCIESlot which represents common part of
pcie slot.(root and downstream.) and helper functions for it.
helper functions for chassis, slot -> PCIESlot conversion.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The lower bits of base/limit registers is RO and shouldn't be zero
cleared on reset. This patch fixes it.
In fact, the default value of base/limit registers aren't specified
in the spec. And some bridges disable forwarding on reset instead of
zeroing base/limit registers.
So introduce one function to disable bridge forwarding so that
such bridges can use it. It will be used later.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
add pcie constants to pcie_regs.h.
Those constants should go to Linux pci_regs.h and then the file should
go away eventually.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
use pci_clear_bit_word() in pci_device_reset() where appropriate.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
this patch implements helper functions to handle msi-x and msi
uniformly.
They will be used later.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch introduces helper functions to test-and-{clear, set} mask in configuration
space. pci_{byte, word, long, quad}_test_and_{clear, set}_mask().
They will be used later.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Clear w1cmask when deleting a pci capability.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Compiling with GCC 4.6.0 20100925 produced warnings like:
/src/qemu/net/tap-win32.c: In function 'tap_win32_open':
/src/qemu/net/tap-win32.c:582:12: error: variable 'hThread' set but not used [-Werror=unused-but-set-variable]
Fix by removing the unused variables.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Only Mac-on-Linux stuff used video.x, OpenBIOS does not need it.
Remove video.x MoL hacks.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Compiling with GCC 4.6.0 20100925 produced a warning:
/src/qemu/hw/lsi53c895a.c: In function 'lsi_do_msgout':
/src/qemu/hw/lsi53c895a.c:848:9: error: variable 'len' set but not used [-Werror=unused-but-set-variable]
Fix by adding a dummy cast so that the variable is not unused for
non-debug case.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Compiling with GCC 4.6.0 20100925 produced warnings:
/src/qemu/hw/eepro100.c: In function 'eepro100_read4':
/src/qemu/hw/eepro100.c:1351:14: error: 'val' may be used uninitialized in this function [-Werror=uninitialized]
/src/qemu/hw/eepro100.c: In function 'eepro100_read2':
/src/qemu/hw/eepro100.c:1328:14: error: 'val' may be used uninitialized in this function [-Werror=uninitialized]
/src/qemu/hw/eepro100.c: In function 'eepro100_read1':
/src/qemu/hw/eepro100.c:1285:13: error: 'val' may be used uninitialized in this function [-Werror=uninitialized]
Fix by initializing 'val' at start.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Compiling with GCC 4.6.0 20100925 produced a lot of warnings like:
In file included from /src/qemu/hw/cirrus_vga_rop.h:174:0,
from /src/qemu/hw/cirrus_vga.c:284:
/src/qemu/hw/cirrus_vga_rop2.h: In function 'cirrus_patternfill_0_8':
/src/qemu/hw/cirrus_vga_rop2.h:48:18: error: variable 'col' set but not used [-Werror=unused-but-set-variable]
/src/qemu/hw/cirrus_vga_rop2.h: In function 'cirrus_colorexpand_transp_0_8':
/src/qemu/hw/cirrus_vga_rop2.h:104:18: error: variable 'col' set but not used [-Werror=unused-but-set-variable]
Fix the warnings by introducing an inline function, which avoids
exposing write-only variables.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Commit d729bb9a77 has a typo, causing an
infinite loop in acpi_table_add.
Signed-off-by: Vincent Minet <vincent@vincent-minet.net>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
When using irqfd with vhost-net to inject interrupts,
a single evenfd might inject multiple interrupts.
Implementing this is much easier with a single
per-device callback to set guest notifiers.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
I reviewed the latest sources of Linux, FreeBSD and NetBSD.
They all reset the multiple IA bit (multi_ia in BSD) to zero,
but I did not find code which sets this bit to one
(like it is done by some routers).
Running Windows guests also did not set this bit.
Intel's Open Source Software Developer Manual does not
give much information on the semantics related to this bit,
so I had to guess how it works. The guess was good enough
to make the router emulation work.
Related changes in this patch:
* Update naming and documentation of the internal hash register.
It is not limited to multicast, but also used for multiple IA.
* Dump complete configuration register when debug traces are enabled.
* Debug output when multiple IA bit is set during CmdConfigure.
* Debug output when frames are received because multiple IA bit is set,
or when they are ignored although it is set.
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move all of vhost-net start/stop logic to a single routine,
and call it from everywhere.
Additionally, start/stop vhost-net on link up/down:
we should not transmit anything if user asked us to
put the link down.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
As status is set to 0 on reset, invoke the relevant callback. This makes
for a cleaner code in devices as they don't need to duplicate the code
in their reset routine, as well as excercises this path a little more.
In particular this makes it possible to unify
vhost-net handling code with the following patch.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
min was unknown here, so avoid it.
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
size_t needs a different format specifier, so fix this.
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
With the new gcc format warnings, gcc detected this:
/qemu/hw/virtio-9p.c:1040: error: format ‘%u’ expects type ‘unsigned int’, but argument 4 has type ‘__nlink_t’
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Since version 4.4.x, gcc supports additional format attributes.
__attribute__ ((format (gnu_printf, 1, 2)))
should be used instead of
__attribute__ ((format (printf, 1, 2))
because QEMU always uses standard format strings (even with mingw32).
The patch replaces format attribute printf / __printf__ by macro
GCC_FMT_ATTR which uses gnu_printf if supported.
It also removes an #ifdef __GNUC__ (not needed any longer).
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Fix address truncation in sysbus by using a wider type.
Reported-by: Artyom Tarasenko <atar4qemu@googlemail.com>
Tested-by: Andreas Färber <andreas.faerber@web.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The addition of memory stats reporting to the virtio balloon causes
the 'info balloon' command to become asynchronous. This is a regression
because in some cases it can hang the user monitor.
This is an alternative to Adam Litke's patch. Adam's patch disabled the
corresponding (guest-visible) virtio feature bit, causing issues for migration.
Original discussion is available at:
http://marc.info/?l=qemu-devel&m=128448124328314&w=2
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Adam Litke <agl@us.ibm.com
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
vl.c has a Sun-specific hack to supply a prototype for madvise(),
but the call site has apparently moved to arch_init.c.
Haiku doesn't implement madvise() in favor of posix_madvise().
OpenBSD and Solaris 10 don't implement posix_madvise() but madvise().
MinGW implements neither.
Check for madvise() and posix_madvise() in configure and supply qemu_madvise()
as wrapper. Prefer madvise() over posix_madvise() due to flag availability.
Convert all callers to use qemu_madvise() and QEMU_MADV_*.
Note that on Solaris the warning is fixed by moving the madvise() prototype,
not by qemu_madvise() itself. It helps with porting though, and it simplifies
most call sites.
v7 -> v8:
* Some versions of MinGW have no sys/mman.h header. Reported by Blue Swirl.
v6 -> v7:
* Adopt madvise() rather than posix_madvise() semantics for returning errors.
* Use EINVAL in place of ENOTSUP.
v5 -> v6:
* Replace two leftover instances of POSIX_MADV_NORMAL with QEMU_MADV_INVALID.
Spotted by Blue Swirl.
v4 -> v5:
* Introduce QEMU_MADV_INVALID, suggested by Alexander Graf.
Note that this relies on -1 not being a valid advice value.
v3 -> v4:
* Eliminate #ifdefs at qemu_advise() call sites. Requested by Blue Swirl.
This will currently break the check in kvm-all.c by calling madvise() with
a supported flag, which will not fail. Ideas/patches welcome.
v2 -> v3:
* Reuse the *_MADV_* defines for QEMU_MADV_*. Suggested by Alexander Graf.
* Add configure check for madvise(), too.
Add defines to Makefile, not QEMU_CFLAGS.
Convert all callers, untested. Suggested by Blue Swirl.
* Keep Solaris' madvise() prototype around. Pointed out by Alexander Graf.
* Display configure check results.
v1 -> v2:
* Don't rely on posix_madvise() availability, add qemu_madvise().
Suggested by Blue Swirl.
Signed-off-by: Andreas Färber <afaerber@opensolaris.org>
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Make it possible for boards to override the kind of interrupt
to be signaled when the decr timer hits. The 405's signal PIT
interrupts while the 440's signal DECR.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
./hw/sd.c: In function ‘sd_init’:
./hw/sd.c:443: error: implicit declaration of function ‘qemu_blockalign’
./hw/sd.c:443: error: nested extern declaration of ‘qemu_blockalign’
./hw/sd.c:443: error: assignment makes pointer from integer without a cast
Cc: Christoph Hellwig <hch@lst.de>
Cc: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Fix two compiler warnings (when format attribute is applied).
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Fix two compiler warnings (when format attribute is applied)
and one error (missing %) in format strings.
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
For the RESERVE and RELEASE commands the length must be zero
and xfer_mode must be SCSI_XFER_NONE.
Signed-off-by: Bernhard Kohl <bernhard.kohl@nsn.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Ensure that pending requests of a SCSI generic device are purged on
system reset. This also avoids calling a NULL function in lsi53c895a.
The lsi code was recently changed to call the .qdev.reset function.
Signed-off-by: Bernhard Kohl <bernhard.kohl@nsn.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
IDE is a bit ugly in this respect. For one it doesn't really keep track
of a sector size - most of the protocol is in units of 512 bytes, and we
assume 2048 bytes for CDROMs which is correct most of the time.
Second IDE allocates an I/O buffer long before we know if we're dealing
with a CDROM or not, so increase the alignment for the io_buffer
unconditionally.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Use qemu_blockalign for all allocations in the block layer. This allows
increasing the required alignment, which is need to support O_DIRECT on
devices with large block sizes.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
clear not only INTA, but all INTx when MSI-X is enabled.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Implement RW1C register framework.
With this patch, it would be easy to implement
W1C(Write 1 to Clear) register by just setting w1cmask.
Later RW1C register will be used by pcie.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The OpenIndiana (Solaris) e1000g driver drops frames that are too long
or too short. It expects to receive frames of at least the Ethernet
minimum size. ARP requests in particular are small and will be dropped
if they are not padded appropriately, preventing a Solaris VM from
becoming visible on the network.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If the compiler supports the warning flag -Wempty-body, use it.
Adjust the code to avoid the warnings.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Fix SSSR TFN logic: TX FIFO is never filled, so it is always in
underrun condition if SSP is enabled.
This also avoids a gcc warning with -Wtype-limits.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Remove checks which were made useless by r5849,
8da3ff1809.
This also avoids a warning with GCC flag -Wtype-limits.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Use range_covers_byte() instead of comparisons.
This avoids some warnings with GCC flag -Wtype-limits.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Extract range functions from pci.h. These will be used by later patches
by non-PCI devices. Adjust current users.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Because of the use of unsigned types, possible errors during
BIOS or kernel load were ignored.
Fix by using a signed type.
This also avoids some warnings with GCC flag -Wtype-limits.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This is the patch to update serial port parameters after guest is
already loaded.
Signed-off-by: Michal Novotny <minovotn@redhat.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
file.index is unsigned, hence 'while (--file.index >= 0)'
will loop > forever. Change to while (file.index-- > 0).
Reported-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Macros normally should not end with a semicolon,
otherwise their usage results in two statements
where only one statement was expected.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Abort when invalid value for region_num is passed to pci_register_bar.
That is caller's bug. Abort instead of silently ignoring invalid value.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch sorts out invalid use of pcibus_t.
In pci_register_bar(), pcibus_t wmask is used. It should,
however, be uint64_t because it is used to set
pci configuration space value(PCIDevice::wmask)
by pci_set_quad() or pci_set_long().
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Sending ESP a command caused it to trigger DMA immediately
even if DMA was not enabled at the DMA controller.
Add a signal from DMA controller to ESP to tell ESP about changes in
DMA enable bit. Also use the correct function for setting up GPIO outputs.
This fixes NetBSD 1.6.1 through 3.0 boot.
Thanks to Artyom Tarasenko for extensive debugging of the problem.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Janne Huttunen noticed that the FIFO end pointer is updated by the
guest after writing each word to the FIFO, at least the X.org driver
which is open does this. This means that there's no way for the
host to know if the guest is in the middle a write operation. Qemu
thus needs to read the beginning of the command up to when it's able
to tell how many words are expected for the given command. It will
abort reading and rewind the FIFO if there aren't enough words yet,
this should be relatively rare but it is suspected to have been the
cause of the occasional FIFO overrun that killed the display.
Character devices created by qemu_chr_open don't
allow duplicate device names, so naming all
UART devices "null" no longer works.
Running "qemu-system-arm -M n800" (and some other machines)
results in this error message:
qemu-system-arm: Duplicate ID 'null' for chardev
Can't create serial device, empty char device
This is fixed by setting a default label "uart1",
"uart2" or "uart3".
Cc: Andrzej Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
This patch adds trace events for virtqueue operations including
adding/removing buffers, notifying the guest, and receiving a notify
from the guest.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Symbols with a size of 0 are unusable for the disassembler.
Example:
While running an arm linux kernel, no symbolic names are
used in qemu.log when the cpu is executing an assembler function.
Assume that the size of such symbols is the difference to the
next symbol value.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This patch applies on top of 9P2000.L patches that we have on the list.
I took a look at how 9P server is handling open() flags in 9P2000.L path.
I think we can do away with the valid_flags() function and simplify the
code. The reasoning is as follows:
O_NOCTTY: (If the file is a terminal, don't make it the controlling
terminal of the process even though the process does not have a controlling
terminal) By the time the control reaches 9P client it is clear that what
we have is not a terminal device. Hence it does not matter what we do with
this flag. In any case 9P server can filter this flag out before making the
syscall.
O_NONBLOCK: (Don't block if i) Can't read/write to the file ii) Can't get
locks) This has an impact on FIFOs, but also on file locks. Hence we can
pass it down to the system call.
O_ASYNC: From the manpage:
O_ASYNC
Enable signal-driven I/O: generate a signal (SIGIO by default, but
this can be changed via fcntl(2)) when input or output becomes pos-
sible on this file descriptor. This feature is only available for
terminals, pseudo-terminals, sockets, and (since Linux 2.6) pipes
and FIFOs. See fcntl(2) for further details.
Again, this does not make any impact on regular files handled by 9P. Also,
we don't want 9P server to receive SIGIO. Hence I think 9P server can
filter this flag out before making the syscall.
O_CLOEXEC: This flag makes sense only on the client. If guest user space
sets this flag the guest VFS will take care of calling close() on the fd if
an exec() happens. Hence 9P client need not be bothered with this flag.
Also I think QEMU will not do an exec, but if it does, it makes sense to
close these fds. Hence we can pass this flag down to the syscall.
O_CREAT: Since we are in open() path it means we have confirmed that the file
exists. Hence there is no need to pass O_CREAT flag down to the system. In fact
on some versions of glibc this causes problems, because we pass O_CREAT flag,
but don't have permission bits. Hence we can just mask this flag out.
So in summary:
Mask out:
O_NOCTTY
O_ASYNC
O_CREAT
Pass-through:
O_NONBLOCK
O_CLOEXEC
Signed-off-by: Sripathi Kodi <sripathik@in.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
This is equivalent to SM_PASSTHROUGH security model.
The only exception is, failure of privilige operation like chown
are ignored. This makes a passthrough like security model usable
for people who runs kvm as non root
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
With mapped security mode we use "user.virtfs" namespace is used
to store the virtFs related attributes. So hide it from user.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
TXATTRCREATE: Prepare a fid for setting xattr value on a file system object.
size[4] TXATTRCREATE tag[2] fid[4] name[s] attr_size[8] flags[4]
size[4] RXATTRWALK tag[2]
txattrcreate gets a fid pointing to xattr. This fid can later be
used to get set the xattr value.
flag value is derived from set Linux setxattr. The manpage says
"The flags parameter can be used to refine the semantics of the operation.
XATTR_CREATE specifies a pure create, which fails if the named attribute
exists already. XATTR_REPLACE specifies a pure replace operation, which
fails if the named attribute does not already exist. By default (no flags),
the extended attribute will be created if need be, or will simply replace
the value if the attribute exists."
The actual setxattr operation happens when the fid is clunked. At that point
the written byte count and the attr_size specified in TXATTRCREATE should be
same otherwise an error will be returned.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
TXATTRWALK: Descend a ATTR namespace
size[4] TXATTRWALK tag[2] fid[4] newfid[4] name[s]
size[4] RXATTRWALK tag[2] size[8]
txattrwalk gets a fid pointing to xattr. This fid can later be
used to get read the xattr value. If name is NULL the fid returned
can be used to get the list of extended attribute associated to
the file system object.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Implement 9p2000.L version of open(LOPEN) interface in qemu 9p server.
For LOPEN, no need to convert the flags to and from 9p mode to VFS mode.
Synopsis:
size[4] Tlopen tag[2] fid[4] mode[4]
size[4] Rlopen tag[2] qid[13] iounit[4]
Current qemu 9p server does not support following flags:
O_NOCTTY, O_NONBLOCK, O_ASYNC & O_CLOEXEC
[Fix mode format - jvrao@linux.vnet.ibm.com]
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
size[4] Trename tag[2] fid[4] newdirfid[4] name[s]
size[4] Rrename tag[2]
Implement the 2000.L rename operation. A new function
v9fs_complete_rename is introduced that acts as a common entry point
for 2000.L rename operation and 2000.U rename opearation (via wstat).
As part of this change the field 'nname' (used only for rename) is
removed from the structure V9fsWstatState. Instead a new structure
V9fsRenameState is used for rename operations both by 2000.U and 2000.L
code paths. Both 2000.U and 2000.L rename code paths construct the
V9fsRenameState structure and passes that to v9fs_complete_rename
function.
Changes from previous version:
Use qemu_mallocz to initialize
Use strcpy,strcat functions instead of memcpy
Changed the variable name to newdirfid
Introduced post rename function
Error checking
Removed nname field from V9fsWstatState
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Synopsis
size[4] Tmkdir tag[2] fid[4] name[s] mode[4] gid[4]
size[4] Rmkdir tag[2] qid[13]
Description
mkdir asks the file server to create a directory with given name,
mode and gid. The qid for the new directory is returned with
the mkdir reply message.
Note: 72 is selected as the opcode for TMKDIR from the reserved list.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
[jvrao@linux.vnet.ibm.com: Fix perm handling when creating directory]
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Implement TMKNOD as part of 2000.L Work
Synopsis
size[4] Tmknod tag[2] fid[4] name[s] mode[4] major[4] minor[4] gid[4]
size[4] Rmknod tag[2] qid[13]
Description
mknod asks the file server to create a device node with given device
type, mode and gid. The qid for the new device node is returned with
the mknod reply message.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
SYNOPSIS
size[4] Tlcreate tag[2] fid[4] name[s] flags[4] mode[4] gid[4]
size[4] Rlcreate tag[2] qid[13] iounit[4]
DESCRIPTION
The Tlreate request asks the file server to create a new regular file with the
name supplied, in the directory (dir) represented by fid.
The mode argument specifies the permissions to use. New file is created with
the uid if the fid and with supplied gid.
The flags argument represent Linux access mode flags with which the caller
is requesting to open the file with. Protocol allows all the Linux access
modes but it is upto the server to allow/disallow any of these acess modes.
If the server doesn't support any of the access mode, it is expected to
return error.
To start with we will not restricit/limit any Linux flags on this server.
If needed, We can start restricting as we move forward with various use cases.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
This patch implements creating a symlink for TSYMLINK request
and responds with RSYMLINK. In the case of error, we return RERROR.
SYNOPSIS
size[4] Tsymlink tag[2] fid[4] name[s] symtgt[s] gid[4]
size[4] Rsymlink tag[2] qid[13]
DESCRIPTION
Create a symbolic link named 'name' pointing to 'symtgt'.
gid represents the effective group id of the caller.
The permissions of a symbolic link are irrelevant hence it is omitted
from the protocol.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
SYNOPSIS
size[4] Tsetattr tag[2] attr[n]
size[4] Rsetattr tag[2]
DESCRIPTION
The setattr command changes some of the file status information.
attr resembles the iattr structure used in Linux kernel. It
specifies which status parameter is to be changed and to what
value. It is laid out as follows:
valid[4]
specifies which status information is to be changed. Possible
values are:
ATTR_MODE (1 << 0)
ATTR_UID (1 << 1)
ATTR_GID (1 << 2)
ATTR_SIZE (1 << 3)
ATTR_ATIME (1 << 4)
ATTR_MTIME (1 << 5)
ATTR_CTIME (1 << 5)
ATTR_ATIME_SET (1 << 7)
ATTR_MTIME_SET (1 << 8)
The last two bits represent whether the time information
is being sent by the client's user space. In the absense
of these bits the server always uses server's time.
mode[4]
File permission bits
uid[4]
Owner id of file
gid[4]
Group id of the file
size[8]
File size
atime_sec[8]
Time of last file access, seconds
atime_nsec[8]
Time of last file access, nanoseconds
mtime_sec[8]
Time of last file modification, seconds
mtime_nsec[8]
Time of last file modification, nanoseconds
Explanation of the patches:
--------------------------
*) The kernel just copies relevent contents of iattr structure to p9_iattr_dotl
structure and passes it down to the client. The only check it has is calling
inode_change_ok()
*) The p9_iattr_dotl structure does not have ctime and ia_file parameters because
I don't think these are needed in our case. The client user space can request
updating just ctime by calling chown(fd, -1, -1). This is handled on server
side without a need for putting ctime on the wire.
*) The server currently supports changing mode, time, ownership and size of the
file.
*) 9P RFC says "Either all the changes in wstat request happen, or none of them
does: if the request succeeds, all changes were made; if it fails, none were."
I have not done anything to implement this specifically because I don't see
a reason.
[jvrao@linux.vnet.ibm.com: Parts of code for handling chown(-1,-1)
Signed-off-by: Sripathi Kodi <sripathik@in.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Currently v9fs_do_utimensat takes a V9fsStat argument and builds
timespec structures. It sets tv_nsec values to 0 by default. Instead
of this it should take struct timespec[2] and pass it down to the
system directly. This will make it more generic and useful
elsewhere.
Signed-off-by: Sripathi Kodi <sripathik@in.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Current code resets file's atime to 0 when there is a change in mtime.
This results in resetting the atime to "1970-01-01 05:30:00". For
example, truncate -s 0 filename results in changing the mtime to the
truncate time, but resets the atime to "1970-01-01 05:30:00". utime
system call does not have any provision to set only mtime or atime. So
change v9fs_wstat_post_chmod function to use utimensat function to change
the atime and mtime fields. If tv_nsec field is set to the special value
"UTIME_OMIT", corresponding file time stamp is not updated.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
SYNOPSIS
size[4] Tgetattr tag[2] fid[4] request_mask[8]
size[4] Rgetattr tag[2] lstat[n]
DESCRIPTION
The getattr transaction inquires about the file identified by fid.
request_mask is a bit mask that specifies which fields of the
stat structure is the client interested in.
The reply will contain a machine-independent directory entry,
laid out as follows:
st_result_mask[8]
Bit mask that indicates which fields in the stat structure
have been populated by the server
qid.type[1]
the type of the file (directory, etc.), represented as a bit
vector corresponding to the high 8 bits of the file's mode
word.
qid.vers[4]
version number for given path
qid.path[8]
the file server's unique identification for the file
st_mode[4]
Permission and flags
st_uid[4]
User id of owner
st_gid[4]
Group ID of owner
st_nlink[8]
Number of hard links
st_rdev[8]
Device ID (if special file)
st_size[8]
Size, in bytes
st_blksize[8]
Block size for file system IO
st_blocks[8]
Number of file system blocks allocated
st_atime_sec[8]
Time of last access, seconds
st_atime_nsec[8]
Time of last access, nanoseconds
st_mtime_sec[8]
Time of last modification, seconds
st_mtime_nsec[8]
Time of last modification, nanoseconds
st_ctime_sec[8]
Time of last status change, seconds
st_ctime_nsec[8]
Time of last status change, nanoseconds
st_btime_sec[8]
Time of creation (birth) of file, seconds
st_btime_nsec[8]
Time of creation (birth) of file, nanoseconds
st_gen[8]
Inode generation
st_data_version[8]
Data version number
request_mask and result_mask bit masks contain the following bits
#define P9_STATS_MODE 0x00000001ULL
#define P9_STATS_NLINK 0x00000002ULL
#define P9_STATS_UID 0x00000004ULL
#define P9_STATS_GID 0x00000008ULL
#define P9_STATS_RDEV 0x00000010ULL
#define P9_STATS_ATIME 0x00000020ULL
#define P9_STATS_MTIME 0x00000040ULL
#define P9_STATS_CTIME 0x00000080ULL
#define P9_STATS_INO 0x00000100ULL
#define P9_STATS_SIZE 0x00000200ULL
#define P9_STATS_BLOCKS 0x00000400ULL
#define P9_STATS_BTIME 0x00000800ULL
#define P9_STATS_GEN 0x00001000ULL
#define P9_STATS_DATA_VERSION 0x00002000ULL
#define P9_STATS_BASIC 0x000007ffULL
#define P9_STATS_ALL 0x00003fffULL
This patch implements the client side of getattr implementation for 9P2000.L.
It introduces a new structure p9_stat_dotl for getting Linux stat information
along with QID. The data layout is similar to stat structure in Linux user
space with the following major differences:
inode (st_ino) is not part of data. Instead qid is.
device (st_dev) is not part of data because this doesn't make sense on the
client.
All time variables are 64 bit wide on the wire. The kernel seems to use
32 bit variables for these variables. However, some of the architectures
have used 64 bit variables and glibc exposes 64 bit variables to user
space on some architectures. Hence to be on the safer side we have made
these 64 bit in the protocol. Refer to the comments in
include/asm-generic/stat.h
There are some additional fields: st_btime_sec, st_btime_nsec, st_gen,
st_data_version apart from the bitmask, st_result_mask. The bit mask
is filled by the server to indicate which stat fields have been
populated by the server. Currently there is no clean way for the
server to obtain these additional fields, so it sends back just the
basic fields.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Sripathi Kodi <sripathik@in.ibm.com>
Compute iounit based on the host filesystem block size and pass it to
client with open/create response. Also return iounit as statfs's f_bsize
for optimal block size transfers.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Reviewd-by: Sripathi Kodi <sripathik@in.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
This patch implements the server part of readdir() implementation for
9p2000.L
SYNOPSIS
size[4] Treaddir tag[2] fid[4] offset[8] count[4]
size[4] Rreaddir tag[2] count[4] data[count]
DESCRIPTION
The readdir request asks the server to read the directory specified by 'fid'
at an offset specified by 'offset' and return as many dirent structures as
possible that fit into count bytes. Each dirent structure is laid out as
follows.
qid.type[1]
the type of the file (directory, etc.), represented as a bit
vector corresponding to the high 8 bits of the file's mode
word.
qid.vers[4]
version number for given path
qid.path[8]
the file server's unique identification for the file
offset[8]
offset into the next dirent.
type[1]
type of this directory entry.
name[256]
name of this directory entry.
Signed-off-by: Sripathi Kodi <sripathik@in.ibm.com>
Reviewed-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Sripathi Kodi <sripathik@in.ibm.com>
In v9fs_remove_post_remove() we currently ignore the error returned by
the previous call to remove() and return an error only if freeing the
fid fails. However, the client expects to see the error from remove().
Currently the client falsely thinks that the remove call has always
succeeded. For example, doing rmdir on a non-empty directory does
not return ENOTEMPTY.
With this patch we ignore the error from free_fid(). The client cannot
use this error value anyway.
Signed-off-by: Sripathi Kodi <sripathik@in.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Implement statfs support in qemu server based on Sripathi's
initial statfs patch.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Sripathi Kodi <sripathik@in.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Make 9P server recognize 9P2000.L protocol version
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
I use a legacy OS which depends on some optional SCSI commands.
In fact this implementation does nothing special, but provides minimum
support for the following commands:
REZERO UNIT
WRITE AND VERIFY(10)
WRITE AND VERIFY(12)
WRITE AND VERIFY(16)
MODE SELECT(6)
MODE SELECT(10)
SEEK(6)
SEEK(10)
Signed-off-by: Bernhard Kohl <bernhard.kohl@nsn.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Fill in word 64 of IDENTIFY data to indicate support for PIO modes 3 and 4.
This allows NetBSD guests to use UltraDMA modes instead of just PIO mode 0.
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The DBD bit does not work as expected.
SCSI-Spec:
http://ldkelley.com/SCSI2/SCSI2/SCSI2-08.html#8.2.10
"A disable block descriptors (DBD) bit of zero indicates that the target
may return zero or more block descriptors in the returned MODE SENSE
data (see 8.3.3), at the target's discretion. A DBD bit of one
specifies that the target shall not return any block descriptors in the
returned MODE SENSE data."
Signed-off-by: Bernhard Kohl <bernhard.kohl@nsn.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
SCSI-Spec:
http://ldkelley.com/SCSI2/SCSI2/SCSI2-08.html#8.2.10
"An initiator may request any one or all of the supported mode pages
from a target. If an initiator issues a MODE SENSE command with a
page code value not implemented by the target, the target shall return
CHECK CONDITION status and shall set the sense key to ILLEGAL REQUEST
and the additional sense code to INVALID FIELD IN CDB."
Signed-off-by: Bernhard Kohl <bernhard.kohl@nsn.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The block descriptor contains the number of blocks, not the highest LBA.
Real hard disks return 0 if the number of blocks exceed the maximum 0xFFFFFF.
SCSI-Spec:
http://ldkelley.com/SCSI2/SCSI2/SCSI2-08.html#8.3.3
"The number of blocks field specifies the number of logical blocks on the
medium to which the density code and block length fields apply. A value
of zero indicates that all of the remaining logical blocks of the logical
unit shall have the medium characteristics specified."
Signed-off-by: Bernhard Kohl <bernhard.kohl@nsn.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The page control (PC) field defines the type of mode parameter values
to be returned in the mode pages:
PC=0 : Current values
PC=1 : Changeable values
PC=2 : Default values
PC=3 : Saved values
The current implementation always returns the same type of parameters.
This is OK for Current and Default values as we don't support changes
to be done by the MODE SELECT command.
For Saved values the following applies (implemented by this patch):
"A PC field value of 3h requests that the target return the saved
values of the mode parameters. Implementation of saved page parameters
is optional. Mode parameters not supported by the target shall be set
to zero. If saved values are not implemented, the command shall be
terminated with CHECK CONDITION status, the sense key set to
ILLEGAL REQUEST and the additional sense code set to
SAVING PARAMETERS NOT SUPPORTED."
For Changeable values the following applies (implemented by this patch):
"A PC field value of 1h requests that the target return a mask denoting
those mode parameters that are changeable. In the mask, the fields of
the mode parameters that are changeable shall be set to all one bits and
the fields of the mode parameters that are non-changeable (i.e. defined
by the target) shall be set to all zero bits."
In newer versions of the SCSI-2 spec the following clause was added.
"If the logical unit does not implement changeable parameters mode pages
and the device server receives a MODE SENSE command with 01b in the PC
field, then the command shall be terminated with CHECK CONDITION status,
with the sense key set to ILLEGAL REQUEST, and the additional sense code
set to INVALID FIELD IN CDB."
This was not yet included in the SCSI-2 Working Drafts from 1986-1993.
I assume that the variant to return CHECK CONDITION for PC=1 is not
widely implemented by real devices. I have a legacy OS which fails,
if MODE_SENSE returns non GOOD for PC=1. So for highest compatibility I
implemented the former variant with this patch.
The last Working Draft X3T9.2 Rev. 10L 7-SEP-93 can be found here:
http://ldkelley.com/SCSI2/SCSI2/SCSI2-08.html#8.2.10
In mode_sense_page() this patch also avoids multiple hard coded
definitions of the same mode page length. Instead I use the varable
p[1]. In fact the returned length of the mode pages 4 and 5 were wrong
(2 bytes less).
Signed-off-by: Bernhard Kohl <bernhard.kohl@nsn.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The header for the MODE SENSE(10) command is 8 bytes long.
Signed-off-by: Bernhard Kohl <bernhard.kohl@nsn.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
