Commit Graph

214 Commits

Author SHA1 Message Date
Maheswara Kurapati
dd0b3271e5 hw/i2c: pmbus: Page #255 is valid page for read requests.
Current implementation of the pmbus core driver treats the read request
for page 255 as invalid request and sets the invalid command bit (bit 7)
in the STATUS_CML register. As per the PMBus specification it is a valid
request.

Refer to the PMBus specification, revision 1.3.1, section 11.10 PAGE,
on the page 58:
  "Setting the PAGE to FFh means that all subsequent comands are to be
   applied to all outputs.

   Some commands, such as READ_TEMPERATURE, may use a common sensor but
   be available on all pages of a device. Such implementations are the
   decision of each device manufacturer or are specified in a PMBus
   Application Profile. Consult the manufacturer's documents or the
   Application Profile Specification as needed."

For e.g.,
The VOUT_MODE is a valid command for page 255 for maxim 31785 device.
refer to Table 1. PMBus Command Codes on page 14 in the datasheet.
https://datasheets.maximintegrated.com/en/ds/MAX31785.pdf

Fixes: 38870253f1 ("hw/i2c: pmbus: fix error returns and guard against out of range accesses")

Signed-off-by: Maheswara Kurapati <quic_mkurapat@quicinc.com>
Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Reviewed-by: Titus Rwantare <titusr@google.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220627154703.148943-4-quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-30 09:21:13 +02:00
Cédric Le Goater
6743af9b10 aspeed/i2c: Change trace event for NORMAL_STOP states
Using a 'stop' string seems more appropriate than 'normal'.

Reviewed-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220628154740.1117349-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-30 09:21:13 +02:00
Cédric Le Goater
33e30f11c7 aspeed/i2c: Enable SLAVE_ADDR_RX_MATCH always
There is no 'slave match interrupt' enable bit in the Interrupt
Control Register. Consider it is always enabled and extend the mask
value 'bus->regs[intr_ctrl_reg]' with the SLAVE_ADDR_RX_MATCH bit when
the interrupt is raised.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-22 09:49:34 +02:00
Klaus Jensen
d72a712ce0 hw/i2c/aspeed: add DEV_ADDR in old register mode
Add support for writing and reading the device address register in old
register mode.

On the AST2400 (only 1 slave address)

  * no upper bits

On the AST2500 (2 possible slave addresses),

  * bit[31] : Slave Address match indicator
  * bit[30] : Slave Address Receiving pending

On the AST2600 (3 possible slave addresses),

  * bit[31-30] : Slave Address match indicator
  * bit[29] : Slave Address Receiving pending

The model could be more precise to take into account all fields but
since the Linux driver is masking the register value being set, it
should be fine. See commit 3fb2e2aeafb2 ("i2c: aspeed: disable
additional device addresses on ast2[56]xx") from Zeiv. This can be
addressed later.

Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg: add details to commit log ]
Message-Id: <20220601210831.67259-3-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-22 09:49:34 +02:00
Klaus Jensen
b03ec4ff06 hw/i2c/aspeed: rework raise interrupt trace event
Build a single string instead of having several parameters on the trace
event.

Suggested-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg: simplified trace buffer creation ]
Message-Id: <20220601210831.67259-2-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-22 09:49:34 +02:00
Cédric Le Goater
b35802ce31 aspeed/i2c: Add ast1030 controller models
Based on :

  https://lore.kernel.org/qemu-devel/20220324100439.478317-2-troy_lee@aspeedtech.com/

Cc: Troy Lee <troy_lee@aspeedtech.com>
Cc: Jamin Lin <jamin_lin@aspeedtech.com>
Cc: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-22 09:49:34 +02:00
Joe Komlodi
e532cd0485 aspeed: i2c: Move regs and helpers to header file
Moves register definitions and short commonly used inlined functiosn to
the header file to help tidy up the implementation file.

Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: I34dff7485b6bbe3c9482715ccd94dbd65dc5f324
Message-Id: <20220331043248.2237838-8-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-22 09:49:34 +02:00
Joe Komlodi
0efec47b5f aspeed: i2c: Add PKT_DONE IRQ to trace
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: I566eb09f4b9016e24570572f367627f6594039f5
Message-Id: <20220331043248.2237838-7-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-22 09:49:34 +02:00
Joe Komlodi
ba2cccd64e aspeed: i2c: Add new mode support
On AST2600, I2C has a secondary mode, called "new mode", which changes
the layout of registers, adds some minor behavior changes, and
introduces a new way to transfer data called "packet mode".

Most of the bit positions of the fields are the same between old and new
mode, so we use SHARED_FIELD_XX macros to reuse most of the code between
the different modes.

For packet mode, most of the command behavior is the same compared to
other modes, but there are some minor changes to how interrupts are
handled compared to other modes.

Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: I072f8301964f623afc74af1fe50c12e5caef199e
Message-Id: <20220331043248.2237838-6-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-22 09:49:34 +02:00
Joe Komlodi
2260fc6ff3 aspeed: i2c: Use reg array instead of individual vars
Using a register array will allow us to represent old-mode and new-mode
I2C registers by using the same underlying register array, instead of
adding an entire new set of variables to represent new mode.

As part of this, we also do additional cleanup to use ARRAY_FIELD_
macros instead of FIELD_ macros on registers.

Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: Ib94996b17c361b8490c042b43c99d8abc69332e3
[ clg: use of memset in aspeed_i2c_bus_reset() ]
Message-Id: <20220331043248.2237838-5-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-22 09:49:34 +02:00
Joe Komlodi
3be3d6ccf2 aspeed: i2c: Migrate to registerfields API
This cleans up some of the field accessing, setting, and clearing
bitwise operations, and wraps them in macros instead.

Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: I33018d6325fa04376e7c29dc4a49ab389a8e333a
Message-Id: <20220331043248.2237838-4-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-22 09:49:34 +02:00
Igor Mammedov
4b66ddcc4d acpi: ich9-smb: add support for AcpiDevAmlIf interface
wire AcpiDevAmlIf interface to build ich9-smb and its slave
devices AML. It will be used by followup patches to switch
from creating AML in ad-hoc way to a more systematic one
that will scan present devices and ask them to provide
their AML code like it's done with ISA devices.

This patch is a partial conversion, as it only fetches
AML from slave devices attached to its I2C bus.

The conversion will be completed when PCI bus is
switched to use AcpiDevAmlIf and build_smb0() could be
dropped.

Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20220608135340.3304695-16-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2022-06-09 19:32:48 -04:00
Markus Armbruster
b21e238037 Use g_new() & friends where that makes obvious sense
g_new(T, n) is neater than g_malloc(sizeof(T) * n).  It's also safer,
for two reasons.  One, it catches multiplication overflowing size_t.
Two, it returns T * rather than void *, which lets the compiler catch
more type errors.

This commit only touches allocations with size arguments of the form
sizeof(T).

Patch created mechanically with:

    $ spatch --in-place --sp-file scripts/coccinelle/use-g_new-etc.cocci \
	     --macro-file scripts/cocci-macro-file.h FILES...

Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20220315144156.1595462-4-armbru@redhat.com>
Reviewed-by: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
2022-03-21 15:44:44 +01:00
Shengtan Mao
648a488216 hw/i2c: Added linear mode translation for pmbus devices
Signed-off-by: Shengtan Mao <stmao@google.com>
Reviewed-by: Titus Rwantare <titusr@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-Id: <20220307200605.4001451-7-titusr@google.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
2022-03-08 18:46:48 +01:00
Titus Rwantare
78fdfc59b1 hw/i2c: pmbus: refactor uint handling
This change cleans up the inputs to pmbus_receive uint, the length of
received data is contained in PMBusDevice state and doesn't need to be
passed around.

Signed-off-by: Titus Rwantare <titusr@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-Id: <20220307200605.4001451-5-titusr@google.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
2022-03-08 18:46:48 +01:00
Titus Rwantare
2192aaae1c hw/i2c: pmbus: add PEC unsupported warning
Signed-off-by: Titus Rwantare <titusr@google.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220307200605.4001451-4-titusr@google.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
2022-03-08 18:46:48 +01:00
Titus Rwantare
38870253f1 hw/i2c: pmbus: fix error returns and guard against out of range accesses
Signed-off-by: Titus Rwantare <titusr@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-Id: <20220307200605.4001451-3-titusr@google.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
2022-03-08 18:46:48 +01:00
Titus Rwantare
32480293db hw/i2c: pmbus: add registers
- add the VOUT_MIN and STATUS_MFR registers

Signed-off-by: Titus Rwantare <titusr@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-Id: <20220307200605.4001451-2-titusr@google.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
2022-03-08 18:46:48 +01:00
Patrick Venture
d8bdf97972 hw/i2c: flatten pca954x mux device
Previously this device created N subdevices which each owned an i2c bus.
Now this device simply owns the N i2c busses directly.

Tested: Verified devices behind mux are still accessible via qmp and i2c
from within an arm32 SoC.

Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220202164533.1283668-1-venture@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2022-03-02 19:27:36 +00:00
Peter Maydell
b5bf5a53d1 Kconfig: Add I2C_DEVICES device group
Currently there is no way for a board model's Kconfig stanza to
say "I have an i2c bus which the user can plug an i2c device into,
build all the free-standing i2c devices". The Kconfig mechanism
for this is the "device group". Add an I2C_DEVICES group along
the same lines as the existing PCI_DEVICES. Simple free-standing
i2c devices which a user might plausibly want to be able to
plug in on the QEMU commandline should have
   default y if I2C_DEVICES
and board models which have an i2c bus that is user-accessible
should use
   imply I2C_DEVICES
to cause those pluggable devices to be built.

In this commit we mark only a fairly conservative set of i2c devices
as belonging to the I2C_DEVICES group: the simple sensors and RTCs
(not including PMBus devices or devices which need GPIO lines to be
connected).

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20220208155911.3408455-2-peter.maydell@linaro.org
2022-02-21 13:30:20 +00:00
Cédric Le Goater
602610383f aspeed/i2c: QOMify AspeedI2CBus
Introduce an AspeedI2CBus SysBusDevice model and attach the associated
memory region and IRQ to the newly instantiated objects.

Before this change, the I2C bus IRQs were all attached to the
SysBusDevice model of the I2C controller. Adapt the AST2600 SoC
realize routine to take into account this change.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
2021-10-12 08:20:08 +02:00
Peter Maydell
9388d1701e qbus: Rename qbus_create() to qbus_new()
Rename the "allocate and return" qbus creation function to
qbus_new(), to bring it into line with our _init vs _new convention.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210923121153.23754-6-peter.maydell@linaro.org
2021-09-30 13:44:08 +01:00
BALATON Zoltan
793abe24aa i2c/smbus_eeprom: Add feature bit to SPD data
Add the differential clock input feature bit to the generated SPD
data. Most guests don't seem to care but pegasos2 firmware version 1.2
checks for this bit and stops with unsupported module type error if
it's not present. Since this feature is likely present on real memory
modules add it in the general code rather than patching the generated
SPD data in pegasos2 board only.

Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <19d42ade295d5297aa624a9eb757b8df18cf64d6.1626367844.git.balaton@eik.bme.hu>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
2021-07-29 10:59:49 +10:00
Titus Rwantare
3746d5c15e hw/i2c: add support for PMBus
QEMU has support for SMBus devices, and PMBus is a more specific
implementation of SMBus. The additions made in this commit makes it easier to
add new PMBus devices to QEMU.

https://pmbus.org/specification-archives/

Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-Id: <20210708172556.1868139-2-titusr@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
2021-07-08 14:15:45 -05:00
Philippe Mathieu-Daudé
90603c5b89 hw/i2c: Introduce i2c_start_recv() and i2c_start_send()
To ease reviewing code using the I2C bus API, introduce the
i2c_start_recv() and i2c_start_send() helpers which don't
take the confusing 'is_recv' boolean argument.

Use these new helpers in the SMBus / AUX bus models.

Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
2021-07-08 14:15:01 -05:00
Philippe Mathieu-Daudé
265caf45c6 hw/i2c: Extract i2c_do_start_transfer() from i2c_start_transfer()
To allow further simplications, extract i2c_do_start_transfer()
from i2c_start_transfer(). This is mostly the same function,
but the former is static and takes an enum argument.

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
2021-07-08 14:15:01 -05:00
BALATON Zoltan
e656e38797 hw/i2c: Make i2c_start_transfer() direction argument a boolean
Make the argument representing the direction of the transfer a
boolean type.
Rename the boolean argument as 'is_recv' to match i2c_recv_send().
Document the function prototype.

Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20200621145235.9E241745712@zero.eik.bme.hu>
[PMD: Split patch, added docstring]
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
2021-07-08 14:15:01 -05:00
Philippe Mathieu-Daudé
c8665a5997 hw/i2c: Rename i2c_set_slave_address() -> i2c_slave_set_address()
Other functions from I2C slave API are named "i2c_slave_XXX()".
Follow that pattern with set_address(). Add docstring along.
No logical change.

Patch created mechanically using:

  $ sed -i s/i2c_set_slave_address/i2c_slave_set_address/ \
    $(git grep -l i2c_set_slave_address)

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
2021-07-08 14:15:01 -05:00
Philippe Mathieu-Daudé
2038a2907c hw/i2c: Remove confusing i2c_send_recv()
We replaced all the i2c_send_recv() calls by the clearer i2c_recv()
and i2c_send(), so we can remove this confusing API.

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
2021-07-08 14:15:01 -05:00
Philippe Mathieu-Daudé
f8ffea755c hw/i2c/ppc4xx_i2c: Replace i2c_send_recv() by i2c_recv() & i2c_send()
Instead of using the confuse i2c_send_recv(), rewrite to directly
call i2c_recv() & i2c_send(), resulting in code easier to review.

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
2021-07-08 14:15:01 -05:00
Philippe Mathieu-Daudé
c699bf610b hw/i2c/ppc4xx_i2c: Add reference to datasheet
It took me a while to find this model datasheet, since it is
an OCR scan. Add a reference to save other developers time.

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
2021-07-08 14:15:01 -05:00
Stefano Garzarella
d0fb9657a3 docs: fix references to docs/devel/tracing.rst
Commit e50caf4a5c ("tracing: convert documentation to rST")
converted docs/devel/tracing.txt to docs/devel/tracing.rst.

We still have several references to the old file, so let's fix them
with the following command:

  sed -i s/tracing.txt/tracing.rst/ $(git grep -l docs/devel/tracing.txt)

Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210517151702.109066-2-sgarzare@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
2021-06-02 06:51:09 +02:00
Peter Maydell
499063d00a Add a bus multiplexer device
This patch set adds a bus multiplexer and the necessary infrastructure
 in the I2C code to allow it to work.
 
 These are common on systems with lots of I2C devices, like an IPMI BMC.
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEE/Q1c5nzg9ZpmiCaGYfOMkJGb/4EFAmCdnpcACgkQYfOMkJGb
 /4EG7BAAkUB1QbYzUChbTqVwrjxBcYmcSSdehKcZlACr9oIjwH/EutKdve/qt+fE
 xCHkxQAo1s+cFMoV0aFlE0UuwSxR42JwuALQcbz0UNGk0uJsgglVS65qqpwQkbiO
 pRnbW7ZjOxVpcjwvP9RvOIaBabUnEvNqrA7SUqs5+yPZVfhi0NqJ0DHZuvv/5L9c
 DV96Adv2UIKA1vqw6aOBULWm5J5zRN+6IjacZ2Qd7xQplilUcJQ5ZqiYskHF9LuT
 NuXoBMk5Dqqy01LYDdnjwxHAUEG31hIhtoaWgqW9AIlPuHUSxesZNsy/3BKZzWhD
 JX5WfKwkAzWx5pfVbmRzNSG8XqHR5nJqOdaJdWsSl2MGgjQ1/MtoIV/uLMozSVu3
 5arQ7frhCXA2Dy1ozPiqIhrdiNlOHDKRTsu468o5eyxzAf+FclVPPZoKsQttaOA9
 eNu+RNFY/nKCW8iAOPdSV4gQ9QwvUv3Z91lVOQjEiBbll3Iix/3r0/bZmQRArLzY
 6WX0hVrhGIqdCFv5aVar0uFZz1n/G6nv3RBo6a6C72Tf+8KvjMrfA/mAXmQLJ/o1
 j0s7G65lE9blyRmg7aBrfASTBPsT+JocIqeLMdMLIVxAAJLhpnQtjSRILmPy9zjl
 TMicA5MEC4BlXqGTJNoMTlOVyG7iC5VZ5qkeFPe1q5A/b5HxwyM=
 =IamZ
 -----END PGP SIGNATURE-----

Merge remote-tracking branch 'remotes/cminyard/tags/for-qemu-6.1-v1' into staging

Add a bus multiplexer device

This patch set adds a bus multiplexer and the necessary infrastructure
in the I2C code to allow it to work.

These are common on systems with lots of I2C devices, like an IPMI BMC.

# gpg: Signature made Thu 13 May 2021 22:48:07 BST
# gpg:                using RSA key FD0D5CE67CE0F59A6688268661F38C90919BFF81
# gpg: Good signature from "Corey Minyard <cminyard@mvista.com>" [unknown]
# gpg:                 aka "Corey Minyard <minyard@acm.org>" [unknown]
# gpg:                 aka "Corey Minyard <corey@minyard.net>" [unknown]
# gpg:                 aka "Corey Minyard <minyard@mvista.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg:          There is no indication that the signature belongs to the owner.
# Primary key fingerprint: FD0D 5CE6 7CE0 F59A 6688  2686 61F3 8C90 919B FF81

* remotes/cminyard/tags/for-qemu-6.1-v1:
  hw/i2c: add pca954x i2c-mux switch
  hw/i2c: move search to i2c_scan_bus method
  hw/i2c: add match method for device search
  hw/i2c: name I2CNode list in I2CBus

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2021-05-14 14:26:23 +01:00
Peter Maydell
d45a5270d0 Trivial patches pull request 20210503
-----BEGIN PGP SIGNATURE-----
 
 iQJGBAABCAAwFiEEzS913cjjpNwuT1Fz8ww4vT8vvjwFAmCPtbASHGxhdXJlbnRA
 dml2aWVyLmV1AAoJEPMMOL0/L748I3wP/Al7yi77BMpts1t3lGMm7EBjKgkppnpr
 wZYEM68bJonvvGiEKQjexn1CUfnDcq7f5SZkzcUNLI4oP57pyywb4/gshN0k/Zz8
 uCDveMfnhbio2sqlXiMsH9TOhcv/4wtXAek/ghP7EOjkBvyXrAFIQ7eEPEB9cp+X
 xxs9DxqfWmrGB6vt7Er78zjfUETSMa+UrheVLwbRMhJcc0Bg8hT2DCn9Lw6IjfOy
 usWdrLTGc6qg1zdZzi8QR7jZ+bNx0h+aJLlm8M4cVitXq9v2wb3+6KdsOAeYioAE
 AsnClw0m8j/xtMh3g4/hB4oCxMj0jRdZ9GIGs8Didw5ZwkXTRvFM1GK1PHxqX4pF
 8xMW6Qq0bSUr4II6bPOukBUMUAnPYdkh+iHXsYSZG0I3u6VZLgMK3AXmKRukAYqe
 kQ1lcRe3Lwsp2h+jMBBsbCWhwYdA3THFO4YO31cUaZ191A7z57905QMbqJG/H3HB
 7IUBYBNbrhgysPsNBvY6Lr7yUJIocMgcfP36UHYcBPsDdZgjNCQZneJlkaRlQb8+
 CtUSF8D614EguzGsWaIn3uBSm9THKKLd1rSXCyTSgrXDI285mXlKmEWZvm236ew0
 OEmIz/Ach/R4268j76enYGa1aubsxnrphUfC3aePu0Wzd3QW4RxnCSq7wc4ARPw7
 WTL7J00P578h
 =aCeG
 -----END PGP SIGNATURE-----

Merge remote-tracking branch 'remotes/vivier2/tags/trivial-branch-for-6.1-pull-request' into staging

Trivial patches pull request 20210503

# gpg: Signature made Mon 03 May 2021 09:34:56 BST
# gpg:                using RSA key CD2F75DDC8E3A4DC2E4F5173F30C38BD3F2FBE3C
# gpg:                issuer "laurent@vivier.eu"
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg:                 aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg:                 aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F  5173 F30C 38BD 3F2F BE3C

* remotes/vivier2/tags/trivial-branch-for-6.1-pull-request: (23 commits)
  hw/rx/rx-gdbsim: Do not accept invalid memory size
  docs: More precisely describe memory-backend-*::id's user
  scripts: fix generation update-binfmts templates
  docs/system: Document the removal of "compat" property for POWER CPUs
  mc146818rtc: put it into the 'misc' category
  Do not include exec/address-spaces.h if it's not really necessary
  Do not include cpu.h if it's not really necessary
  Do not include hw/boards.h if it's not really necessary
  Do not include sysemu/sysemu.h if it's not really necessary
  hw: Do not include qemu/log.h if it is not necessary
  hw: Do not include hw/irq.h if it is not necessary
  hw: Do not include hw/sysbus.h if it is not necessary
  hw: Remove superfluous includes of hw/hw.h
  ui: Fix memory leak in qemu_xkeymap_mapping_table()
  hw/usb: Constify VMStateDescription
  hw/display/qxl: Constify VMStateDescription
  hw/arm: Constify VMStateDescription
  vmstate: Constify some VMStateDescriptions
  Fix typo in CFI build documentation
  hw/pcmcia: Do not register PCMCIA type if not required
  ...

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2021-05-05 13:52:00 +01:00
Thomas Huth
19f4ed3652 hw: Do not include qemu/log.h if it is not necessary
Many files include qemu/log.h without needing it. Remove the superfluous
include statements.

Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210328054833.2351597-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
2021-05-02 17:24:50 +02:00
Cédric Le Goater
3f7a53b224 aspeed/i2c: Rename DMA address space
It improves 'info mtree' output.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210407171637.777743-5-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
2021-05-01 10:03:51 +02:00
Cédric Le Goater
7492515909 aspeed/i2c: Fix DMA address mask
The RAM memory region is now used for DMAs accesses instead of the
memory address space region. Mask off the top bits of the DMA address
to reflect this change.

Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210407171637.777743-4-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
2021-05-01 10:03:51 +02:00
Patrick Venture
065177eece hw/i2c: add pca954x i2c-mux switch
The pca954x is an i2c mux, and this adds support for two variants of
this device: the pca9546 and pca9548.

This device is very common on BMCs to route a different channel to each
PCIe i2c bus downstream from the BMC.

Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-Id: <20210412194522.664594-5-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
2021-04-15 07:10:39 -05:00
Patrick Venture
3f9b32595e hw/i2c: move search to i2c_scan_bus method
Moves the search for matching devices on an i2c bus into a separate
method.  This allows for an object that owns an I2CBus can avoid
duplicating this method.

Tested: A BMC firmware was booted to userspace and i2c devices were
detected.

Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-Id: <20210412194522.664594-4-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
2021-04-15 07:10:30 -05:00
Patrick Venture
513ca82d89 hw/i2c: add match method for device search
At the start of an i2c transaction, the i2c bus searches its list of
children to identify which devices correspond to the address (or
broadcast).  Now the I2CSlave device has a method "match" that
encapsulates the lookup behavior. This allows the behavior to be changed
to support devices, such as i2c muxes.

Tested: A BMC firmware was booted to userspace and i2c devices were
detected.

Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-Id: <20210412194522.664594-3-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
2021-04-15 07:10:06 -05:00
Philippe Mathieu-Daudé
5dfbfefaad hw/i2c/npcm7xx_smbus: Simplify npcm7xx_smbus_init()
The STATUS register will be reset to IDLE in
cnpcm7xx_smbus_enter_reset(), no need to preset
it in instance_init().

Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210228224813.312532-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2021-03-05 15:17:34 +00:00
Hao Wu
6b6e7570d6 hw/i2c: Implement NPCM7XX SMBus Module FIFO Mode
This patch implements the FIFO mode of the SMBus module. In FIFO, the
user transmits or receives at most 16 bytes at a time. The FIFO mode
allows the module to transmit large amount of data faster than single
byte mode.

Since we only added the device in a patch that is only a few commits
away in the same patch set. We do not increase the VMstate version
number in this special case.

Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210210220426.3577804-6-wuhaotsh@google.com
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2021-02-16 14:12:54 +00:00
Hao Wu
94e7787939 hw/i2c: Implement NPCM7XX SMBus Module Single Mode
This commit implements the single-byte mode of the SMBus.

Each Nuvoton SoC has 16 System Management Bus (SMBus). These buses
compliant with SMBus and I2C protocol.

This patch implements the single-byte mode of the SMBus. In this mode,
the user sends or receives a byte each time. The SMBus device transmits
it to the underlying i2c device and sends an interrupt back to the QEMU
guest.

Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210210220426.3577804-2-wuhaotsh@google.com
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2021-02-16 13:49:28 +00:00
Chetan Pant
61f3c91a67 nomaintainer: Fix Lesser GPL version number
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.

This patch contains all the files, whose maintainer I could not get
from ‘get_maintainer.pl’ script.

Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023124424.20177-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Adapted exec.c and qdev-monitor.c to new location]
Signed-off-by: Thomas Huth <thuth@redhat.com>
2020-11-15 17:04:40 +01:00
Peng Liang
3cd27b58dd microbit_i2c: Fix coredump when dump-vmstate
VMStateDescription.fields should be end with VMSTATE_END_OF_LIST().
However, microbit_i2c_vmstate doesn't follow it.  Let's change it.

Fixes: 9d68bf564e ("arm: Stub out NRF51 TWI magnetometer/accelerometer detection")
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Peng Liang <liangpeng10@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201019093401.2993833-1-liangpeng10@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2020-10-20 16:12:00 +01:00
Eduardo Habkost
8063396bf3 Use OBJECT_DECLARE_SIMPLE_TYPE when possible
This converts existing DECLARE_INSTANCE_CHECKER usage to
OBJECT_DECLARE_SIMPLE_TYPE when possible.

$ ./scripts/codeconverter/converter.py -i \
  --pattern=AddObjectDeclareSimpleType $(git grep -l '' -- '*.[ch]')

Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Paul Durrant <paul@xen.org>
Message-Id: <20200916182519.415636-6-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
2020-09-18 14:12:32 -04:00
Eduardo Habkost
8110fa1d94 Use DECLARE_*CHECKER* macros
Generated using:

 $ ./scripts/codeconverter/converter.py -i \
   --pattern=TypeCheckMacro $(git grep -l '' -- '*.[ch]')

Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-12-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-13-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-14-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
2020-09-09 09:27:09 -04:00
Eduardo Habkost
db1015e92e Move QOM typedefs and add missing includes
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.

Patch generated using:

 $ ./scripts/codeconverter/converter.py -i \
   --pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')

which will split "typdef struct { ... } TypedefName"
declarations.

Followed by:

 $ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
    $(git grep -l '' -- '*.[ch]')

which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary

Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
2020-09-09 09:26:43 -04:00
Marc-André Lureau
c8d9333f1f meson: convert hw/i2c
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2020-08-21 06:30:30 -04:00
Paolo Bonzini
243af0225a trace: switch position of headers to what Meson requires
Meson doesn't enjoy the same flexibility we have with Make in choosing
the include path.  In particular the tracing headers are using
$(build_root)/$(<D).

In order to keep the include directives unchanged,
the simplest solution is to generate headers with patterns like
"trace/trace-audio.h" and place forwarding headers in the source tree
such that for example "audio/trace.h" includes "trace/trace-audio.h".

This patch is too ugly to be applied to the Makefiles now.  It's only
a way to separate the changes to the tracing header files from the
Meson rewrite of the tracing logic.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2020-08-21 06:18:24 -04:00