This way we can reuse it for other virtio-blk devices, e.g
vhost-user-blk, which currently does not control its config space size
dynamically.
Signed-off-by: Daniil Tatianin <d-tatianin@yandex-team.ru>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <20220906073111.353245-3-d-tatianin@yandex-team.ru>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This is the first step towards moving all device config size calculation
logic into the virtio core code. In particular, this adds a struct that
contains all the necessary information for common virtio code to be able
to calculate the final config size for a device. This is expected to be
used with the new virtio_get_config_size helper, which calculates the
final length based on the provided host features.
This builds on top of already existing code like VirtIOFeature and
virtio_feature_get_config_size(), but adds additional fields, as well as
sanity checking so that device-specifc code doesn't have to duplicate it.
An example usage would be:
static const VirtIOFeature dev_features[] = {
{.flags = 1ULL << FEATURE_1_BIT,
.end = endof(struct virtio_dev_config, feature_1)},
{.flags = 1ULL << FEATURE_2_BIT,
.end = endof(struct virtio_dev_config, feature_2)},
{}
};
static const VirtIOConfigSizeParams dev_cfg_size_params = {
.min_size = DEV_BASE_CONFIG_SIZE,
.max_size = sizeof(struct virtio_dev_config),
.feature_sizes = dev_features
};
// code inside my_dev_device_realize()
size_t config_size = virtio_get_config_size(&dev_cfg_size_params,
host_features);
virtio_init(vdev, VIRTIO_ID_MYDEV, config_size);
Currently every device is expected to write its own boilerplate from the
example above in device_realize(), however, the next step of this
transition is moving VirtIOConfigSizeParams into VirtioDeviceClass,
so that it can be done automatically by the virtio initialization code.
All of the users of virtio_feature_get_config_size have been converted
to use virtio_get_config_size so it's no longer needed and is removed
with this commit.
Signed-off-by: Daniil Tatianin <d-tatianin@yandex-team.ru>
Message-Id: <20220906073111.353245-2-d-tatianin@yandex-team.ru>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This allows is to instantiate a vhost-user-gpio device as part of a PCI
bus. It is mostly boilerplate which looks pretty similar to the
vhost-user-fs-pci device.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <5f560cab92d0d789b1c94295ec74b9952907d69d.1641987128.git.viresh.kumar@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220802095010.3330793-14-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This creates the QEMU side of the vhost-user-gpio device which connects
to the remote daemon. It is based of vhost-user-i2c code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <5390324a748194a21bc99b1538e19761a8c64092.1641987128.git.viresh.kumar@linaro.org>
[AJB: fixes for qtest, tweaks to feature bits]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Cc: Vincent Whitchurch <vincent.whitchurch@axis.com>
Message-Id: <20220802095010.3330793-13-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The `started` field is manipulated internally within the vhost code
except for one place, vhost-user-blk via f5b22d06fb (vhost: recheck
dev state in the vhost_migration_log routine). Mark that as a FIXME
because it introduces a potential race. I think the referenced fix
should be tracking its state locally.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220802095010.3330793-12-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwittz@nutanix.com>
All the boilerplate virtio code does the same thing (or should at
least) of checking to see if the VM is running before attempting to
start VirtIO. Push the logic up to the common function to avoid
getting a copy and paste wrong.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220802095010.3330793-11-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
These are useful for tracing the lifetime of vhost-user connections.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220802095010.3330793-10-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
If the guest driver attempts to use the UNUSED(30) bit it is
potentially buggy as 6.3 Legacy Interface: Reserved Feature Bits
states it "SHOULD NOT be negotiated". For now just log this guest
error.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20220802095010.3330793-9-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20220802095010.3330793-8-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
There are some extra bits used over a vhost-user connection which are
hidden from the device itself. We need to set them here to ensure we
enable things like the protocol extensions.
Currently net/vhost-user.c has it's own inscrutable way of persisting
this data but it really should live in the core vhost_user code.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220726192150.2435175-7-alex.bennee@linaro.org>
Message-Id: <20220802095010.3330793-2-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This helps us construct strings elsewhere before echoing to the
monitor. It avoids having to jump through hoops like:
monitor_printf(mon, "%s", s->str);
It will be useful in following patches but for now convert all
existing plain "%s" printfs to use the _puts api.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220929114231.583801-33-alex.bennee@linaro.org>
Wrap the bare TranslationBlock pointer into a structure.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This is a heavily used function so lets avoid the cost of
CPU_GET_CLASS. On the romulus-bmc run it has a modest effect:
Before: 36.812 s ± 0.506 s
After: 35.912 s ± 0.168 s
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220811151413.3350684-4-alex.bennee@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220923084803.498337-4-clg@kaod.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
g_new(T, n) is neater than g_malloc(sizeof(T) * n). It's also safer,
for two reasons. One, it catches multiplication overflowing size_t.
Two, it returns T * rather than void *, which lets the compiler catch
more type errors.
This commit only touches allocations with size arguments of the form
sizeof(T).
Patch created mechanically with:
$ spatch --in-place --sp-file scripts/coccinelle/use-g_new-etc.cocci \
--macro-file scripts/cocci-macro-file.h FILES...
The previous iteration was commit a95942b50c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20220923084254.4173111-1-armbru@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
- Fix missing block_acct_setup() with -blockdev
- Keep auto_backing_file post-migration
- file-posix: Fixed O_DIRECT memory alignment
- ide: Fix state after EXECUTE DEVICE DIAGNOSTIC and implement
INITIALIZE DEVICE PARAMETERS
- qemu-img: Wean documentation and help output off '?' for help
- qcow2: fix memory leak and compiler warning
- Code cleanups
-----BEGIN PGP SIGNATURE-----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=IIJz
-----END PGP SIGNATURE-----
Merge tag 'for-upstream' of git://repo.or.cz/qemu/kevin into staging
Block layer patches
- Fix missing block_acct_setup() with -blockdev
- Keep auto_backing_file post-migration
- file-posix: Fixed O_DIRECT memory alignment
- ide: Fix state after EXECUTE DEVICE DIAGNOSTIC and implement
INITIALIZE DEVICE PARAMETERS
- qemu-img: Wean documentation and help output off '?' for help
- qcow2: fix memory leak and compiler warning
- Code cleanups
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEE3D3rFZqa+V09dFb+fwmycsiPL9YFAmM3Hm4RHGt3b2xmQHJl
# ZGhhdC5jb20ACgkQfwmycsiPL9ZhqA//WGN9tlx3Pf1D6SG3PtIG6/2DOJ6/gVNw
# R17BwoGTw36Nmt9xDzrHih753dcguLS19Kd6EySTg6j8mPogmFszquORMgGmcYcW
# 0KtneRR7Y9XsamIGgentek1zsWajsP5muvZQF+hFJyZ24MZtWB+5Ucw2VuUTWnRl
# YaKP/tGMP5sC8nK3Npste/o7yh9Wgv4cv/mdKuyKoxjZhELeTTpHoTC2IZK9bV5I
# Bh19zjPRUPodm37nzONruUVzn53xKK3Qn26ZT5Hgx39HOdccPEu9N8wawQyqLr/x
# 2whcn8kFfpFBLLxVbMYjwcWNo41SCn1itRcgV38PilBvG2UInUFK2QCmVgYxWluB
# 9I5sRasfD3/BPPmw3n+j2TRJ+uvrLkkwXqIhAg+mAeiS0MccWUnLhJLW2S1Yai5L
# nkjkLmuV7KCLQTY39WvKBq0TPgj3QR0WJtEYHuUDtduvzKxAWd47Ff1tEPvFm5Ys
# RpmLSUQdPZiOkiwnV1qVg6a3gbIjUcT0Pai/Knc3iYrwCWLdNSCGoPkVemOg5wvN
# GxsQcKnfayQqIdZU6lBQehUjPamm3ffAEELeqLQXCbZe9lsbhNBXLJjVnA3cOu3f
# 1PX6w+4MNeTg5ZekUJGS1fnYlq9CDOWGSv37+csB8dBhi6vQTc6YjABWU1IrB0S5
# 1ihOYtc8fOo=
# =IIJz
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 30 Sep 2022 12:50:54 EDT
# gpg: using RSA key DC3DEB159A9AF95D3D7456FE7F09B272C88F2FD6
# gpg: issuer "kwolf@redhat.com"
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* tag 'for-upstream' of git://repo.or.cz/qemu/kevin:
hw/ide/core.c: Implement ATA INITIALIZE_DEVICE_PARAMETERS command
tests/qtest/ide-test: Verify that DIAGNOSTIC clears DEV to zero
hw/ide/core: Clear LBA and drive bits for EXECUTE DEVICE DIAGNOSTIC
tests/qtest/ide-test.c: Create disk image for use as a secondary
piix_ide_reset: Use pci_set_* functions instead of direct access
block: use the request length for iov alignment
block: move bdrv_qiov_is_aligned to file-posix
iotests/backing-file-invalidation: Add new test
block/qed: Keep auto_backing_file if possible
block/qcow2: Keep auto_backing_file if possible
gluster: stop using .bdrv_needs_filename
block: make serializing requests functions 'void'
block: use bdrv_is_sg() helper instead of raw bs->sg reading
block: add missed block_acct_setup with new block device init procedure
block: pass OnOffAuto instead of bool to block_acct_setup()
qemu-img: Wean documentation and help output off '?' for help
block/qcow2-bitmap: Add missing cast to silent GCC error
qcow2: fix memory leak in qcow2_read_extensions
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
* Fix breakage of icount mode when guest touches MDCR_EL3, MDCR_EL2,
PMCNTENSET_EL0 or PMCNTENCLR_EL0
* Make writes to MDCR_EL3 use PMU start/finish calls
* Let AArch32 write to SDCR.SCCD
* Rearrange cpu64.c so all the CPU initfns are together
* hw/arm/xlnx-zynqmp: Connect ZynqMP's USB controllers
* hw/arm/virt: fix some minor issues with generated device tree
* Fix regression where EL3 could not write to SP_EL1 if there is no EL2
-----BEGIN PGP SIGNATURE-----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=edYy
-----END PGP SIGNATURE-----
Merge tag 'pull-target-arm-20220930' of https://git.linaro.org/people/pmaydell/qemu-arm into staging
target-arm queue:
* Fix breakage of icount mode when guest touches MDCR_EL3, MDCR_EL2,
PMCNTENSET_EL0 or PMCNTENCLR_EL0
* Make writes to MDCR_EL3 use PMU start/finish calls
* Let AArch32 write to SDCR.SCCD
* Rearrange cpu64.c so all the CPU initfns are together
* hw/arm/xlnx-zynqmp: Connect ZynqMP's USB controllers
* hw/arm/virt: fix some minor issues with generated device tree
* Fix regression where EL3 could not write to SP_EL1 if there is no EL2
# -----BEGIN PGP SIGNATURE-----
#
# iQJNBAABCAA3FiEE4aXFk81BneKOgxXPPCUl7RQ2DN4FAmM28EYZHHBldGVyLm1h
# eWRlbGxAbGluYXJvLm9yZwAKCRA8JSXtFDYM3mw9D/44e72KHZdfr3F/Cmd0Jku2
# g5NQ4ooKV90rY4Y4+/VR9Z2k7a72lWFgFl7/54AKXSZsZSmNomeh2WxWJAs1lA2W
# 4rmGPlLwxZYMQumYcMOArYxJQgRK5exVtE6ECKM/JERjhKSbnL1lyLWGUyLtFJfq
# SjxoTWEigPHu+0fX/nk04rFzrA6Bo1qKQqZZTuN9zcT6JXyQMjZNF89Fxy9OlV4s
# dlOXsZILV8oREnGdDFPYLgwSTMn+1rrD8xfjK/DTQrlUVX/9zhlIeKg5O4JadxCy
# 8ThIFCyODUanlRvyjHiwvcvStHn8wwyCp4uJrxmZGyyp4t4u3etG0hpsZaPtiN9O
# NKtad4Aoc6lSmIDhYYZA1LIIdSIeyUPD/LyWTd+qKK7A7mxH6ORr0uyjhb01jWs3
# ceyne1i0n66oRLbHxPyjQEkLqwLl2CsqWr41BNM5RVoYjCU8HYSvEwlh7t+EZCL5
# IRkfAWJkA9bdXL30ZmYSzJ7hfvVkWhDsHD+eOzAcsxoApgzI5Mfi7gCIZ+LNY20P
# W0akGbA6l0InsmIcBpyXEztPOi6tOD/J55qeOCrzHjgfhoJWCoa/mS8bVqN0mKIA
# yJ7QbiK/JY6+G1v2oM8aARLn8/C7oLnMYiKntXNBMj67Ry5GwjDt+A37MUHgQbZb
# yUzUjr3O2N1qJRKi+Dd7eA==
# =edYy
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 30 Sep 2022 09:33:58 EDT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [full]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [full]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [full]
# gpg: aka "Peter Maydell <peter@archaic.org.uk>" [unknown]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* tag 'pull-target-arm-20220930' of https://git.linaro.org/people/pmaydell/qemu-arm:
target/arm: mark SP_EL1 with ARM_CP_EL3_NO_EL2_KEEP
hw/arm/virt: Fix devicetree warning about the SMMU node
hw/arm/virt: Use "msi-map" devicetree property for PCI
hw/arm/virt: Fix devicetree warning about the GIC node
hw/arm/virt: Fix devicetree warning about the root node
hw/arm/xlnx-zynqmp: Connect ZynqMP's USB controllers
target/arm: Rearrange cpu64.c so all the CPU initfns are together
target/arm: Update SDCR_VALID_MASK to include SCCD
target/arm: Make writes to MDCR_EL3 use PMU start/finish calls
target/arm: Mark registers which call pmu_op_start() as ARM_CP_IO
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We don't want it to be possible to re-read the RNG seed after ingesting
it, because this ruins forward secrecy. Currently, however, the setup
data section can just be re-read. Since the kernel is always read after
the setup data, use the selection of the kernel as a trigger to
re-initialize the RNG seed, just like we do on reboot, to preserve
forward secrecy.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Message-Id: <20220922152847.3670513-1-Jason@zx2c4.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CHS-based disk utilities and operating systems may adjust the logical
geometry of a hard drive to cope with the expectations or limitations
of software using the ATA INITIALIZE_DEVICE_PARAMETERS command.
Prior to this patch, INITIALIZE_DEVICE_PARAMETERS was a nop that
always returned success, raising the possibility of data loss or
corruption if the CHS<->LBA translation redirected a write to the
wrong sector.
* hw/ide/core.c
ide_reset():
Reset the logical CHS geometry of the hard disk when the power-on
defaults feature is enabled.
cmd_specify():
a) New function implementing INITIALIZE_DEVICE_PARAMETERS.
b) Ignore calls for empty or ATAPI devices.
cmd_set_features():
Implement the power-on defaults enable and disable features.
struct ide_cmd_table:
Switch WIN_SPECIFY from cmd_nop() to cmd_specify().
ide_init_drive():
Set new fields 'drive_heads' and 'drive_sectors' based upon the
actual disk geometry.
* include/hw/ide/internal.h
struct IDEState:
a) Store the actual drive CHS values within the new fields
'drive_heads' and 'drive_sectors.'
b) Track whether a soft IDE reset should also reset the logical CHS
geometry of the hard disk within the new field 'reset_reverts'.
Signed-off-by: Lev Kujawski <lkujaw@member.fsf.org>
Message-Id: <20220707031140.158958-7-lkujaw@member.fsf.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Prior to this patch, cmd_exec_dev_diagnostic relied upon
ide_set_signature to clear the device register. While the
preservation of the drive bit by ide_set_signature is necessary for
the DEVICE RESET, IDENTIFY DEVICE, and READ SECTOR commands,
ATA/ATAPI-6 specifies that "DEV shall be cleared to zero" for EXECUTE
DEVICE DIAGNOSTIC.
This deviation was uncovered by the ATACT Device Testing Program
written by Hale Landis.
Signed-off-by: Lev Kujawski <lkujaw@member.fsf.org>
Message-Id: <20220707031140.158958-3-lkujaw@member.fsf.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Eliminate the remaining TODOs in hw/ide/piix.c by:
* Using pci_set_{size} functions to write the PIIX PCI configuration
space instead of manipulating it directly as an array; and
* Documenting the default register values by reference to the
controlling specification.
Signed-off-by: Lev Kujawski <lkujaw@member.fsf.org>
Message-Id: <20220707031140.158958-1-lkujaw@member.fsf.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit 5f76a7aac1 is looking harmless from
the first glance, but it has changed things a lot. 'libvirt' uses it to
detect that it should follow new initialization way and this changes
things considerably. With this procedure followed, blockdev_init() is
not called anymore and thus block_acct_setup() helper is not called.
This means in particular that defaults for block accounting statistics
are changed and account_invalid/account_failed are actually initialized
as false instead of true originally.
This commit changes things to match original world. There are the following
constraints:
* new default value in block_acct_init() is set to true
* block_acct_setup() inside blockdev_init() is called before
blkconf_apply_backend_options()
* thus newly created option in block device properties has precedence if
specified
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
CC: Peter Krempa <pkrempa@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: John Snow <jsnow@redhat.com>
CC: Kevin Wolf <kwolf@redhat.com>
CC: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220824095044.166009-3-den@openvz.org>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The structure is for device dvsec not port dvsec. Change type to fix
this issue.
Signed-off-by: Tong Zhang <t.zhang2@samsung.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20220915175853.2902-1-t.zhang2@samsung.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
GCC issues a false positive warning, resulting in build failure with -Werror:
In file included from /usr/include/glib-2.0/glib.h:114,
from src/include/glib-compat.h:32,
from src/include/qemu/osdep.h:144,
from ../src/hw/virtio/vhost-shadow-virtqueue.c:10:
In function ‘g_autoptr_cleanup_generic_gfree’,
inlined from ‘vhost_handle_guest_kick’ at ../src/hw/virtio/vhost-shadow-virtqueue.c:292:42:
/usr/include/glib-2.0/glib/glib-autocleanups.h:28:3: error: ‘elem’ may be used uninitialized [-Werror=maybe-uninitialized]
28 | g_free (*pp);
| ^~~~~~~~~~~~
../src/hw/virtio/vhost-shadow-virtqueue.c: In function ‘vhost_handle_guest_kick’:
../src/hw/virtio/vhost-shadow-virtqueue.c:292:42: note: ‘elem’ was declared here
292 | g_autofree VirtQueueElement *elem;
| ^~~~
cc1: all warnings being treated as errors
There is actually no problem since "elem" is initialized in both branches.
Silence the warning by initializig it with "NULL".
$ gcc --version
gcc (GCC) 12.2.0
Fixes: 9c2ab2f1ec ("vhost: stop transfer elem ownership in vhost_handle_guest_kick")
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220910151117.6665-1-shentey@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The SMMUv3 node isn't expected to have clock properties
(unlike the SMMUv2). Fix the corresponding dt-validate warning:
smmuv3@9050000: 'clock-names', 'clocks' do not match any of the regexes: 'pinctrl-[0-9]+'
From schema: linux/Documentation/devicetree/bindings/iommu/arm,smmu-v3.yaml
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: tweaked commit message as suggested by Eric]
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220927100347.176606-7-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The "msi-parent" property can be used on the PCI node when MSIs do not
contain sideband data (device IDs) [1]. In QEMU, MSI transactions
contain the requester ID, so the PCI node should use the "msi-map"
property instead of "msi-parent". In our case the property describes an
identity map between requester ID and sideband data.
This fixes a warning when passing the DTB generated by QEMU to dtc,
following a recent change to the GICv3 node:
Warning (msi_parent_property): /pcie@10000000:msi-parent: property size (4) too small for cell size 1
[1] linux/Documentation/devicetree/bindings/pci/pci-msi.txt
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220927100347.176606-4-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GICv3 bindings requires a #msi-cells property for the ITS node. Fix
the corresponding dt-validate warning:
interrupt-controller@8000000: msi-controller@8080000: '#msi-cells' is a required property
From schema: linux/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.yaml
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220927100347.176606-3-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The devicetree specification requires a 'model' property in the root
node. Fix the corresponding dt-validate warning:
/: 'model' is a required property
From schema: dtschema/schemas/root-node.yaml
Use the same name for model as for compatible. The specification
recommends that 'compatible' follows the format 'manufacturer,model' and
'model' follows the format 'manufacturer,model-number'. Since our
'compatible' doesn't observe this, 'model' doesn't really need to
either.
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220927100347.176606-2-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect ZynqMP's USB controllers.
Signed-off-by: Francisco Iglesias <francisco.iglesias@amd.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20220920081517.25401-1-frasse.iglesias@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As the close-on-exec flags is not set on the file descriptors returned
by socketpair() at default, the fds will survive across exec' function.
In the case that exec' function get invoked, such as the live-update feature
which is been developing, it will cause fd leaks.
To address this problem, we should call qemu_socketpair() to create an pair of
connected sockets with the close-on-exec flag set.
Signed-off-by: Guoyi Tu <tugy@chinatelecom.cn>
Reviewed-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <7002b12a5fb0a30cd878e14e07da61c36da72913.1661240709.git.tugy@chinatelecom.cn>
Unaligned i/o access on serial UART works on real PCs.
This is used for example by FreeDOS CTMouse driver. Without this it
can't reset and detect serial mice.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/77
Signed-off-by: Arwed Meyer <arwed.meyer@gmx.de>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20220911181840.8933-6-arwed.meyer@gmx.de>
This was deprecated in 6.2 and is ready to go. It removes quite a bit
of code that handled the registration of watchdog models.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On error, vfio_get_iommu_info() frees and clears *info, but
vfio_connect_container() continues to use the pointer regardless
of the return value. Restructure the code such that a failure
of this function triggers an error and clean up the remainder of
the function, including updating an outdated comment that had
drifted from its relevant line of code and using host page size
for a default for better compatibility on non-4KB systems.
Reported-by: Nicolin Chen <nicolinc@nvidia.com>
Link: https://lore.kernel.org/all/20220910004245.2878-1-nicolinc@nvidia.com/
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Nicolin Chen <nicolinc@nvidia.com>
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Link: https://lore.kernel.org/r/166326219630.3388898.12882473157184946072.stgit@omen
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The structure VFIOMigration of a VFIODevice is allocated and initialized
in vfio_migration_init(). "device_state" and "vm_running" are initialized
to 0, indicating that VFIO device is_STOP and VM is not-running. The
initialization value is incorrect. According to the agreement, default
state of VFIO device is _RUNNING. And if a VFIO device is hot-plugged
while the VM is running, "vm_running" should be 1. This patch fixes it.
Fixes: 02a7e71b1e ("vfio: Add VM state change handler to know state of VM")
Signed-off-by: Kunkun Jiang <jiangkunkun@huawei.com>
Link: https://lore.kernel.org/r/20220711014651.1327-1-jiangkunkun@huawei.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Make guest os access pci device control 2 reg for passthrough device
as struct XenPTRegInfo described in the file hw/xen/xen_pt.h.
/* reg read only field mask (ON:RO/ROS, OFF:other) */
uint32_t ro_mask;
/* reg emulate field mask (ON:emu, OFF:passthrough) */
uint32_t emu_mask;
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1196
Signed-off-by: Aaron Liu <Aaron.Liu@amd.com>
Signed-off-by: Ruili Ji <ruili.ji@amd.com>
Message-ID: <BL1PR12MB599341DC55BA53FE588DE14E9B7E9@BL1PR12MB5993.namprd12.prod.outlook.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This reverts 3824e25db1 ("x86: disable rng seeding via setup_data"), but
for 7.2 rather than 7.1, now that modifying setup_data is safe to do.
Cc: Laurent Vivier <laurent@vivier.eu>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Message-Id: <20220921093134.2936487-4-Jason@zx2c4.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since this is read from fw_cfg on each boot, the kernel zeroing it out
alone is insufficient to prevent it from being used twice. And indeed on
reboot we always want a new seed, not the old one. So re-fill it in this
circumstance.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Message-Id: <20220921093134.2936487-3-Jason@zx2c4.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The preferred style is SetupData as a typedef, not setup_data as a plain
struct.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Message-Id: <20220921093134.2936487-2-Jason@zx2c4.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If setup_data is being read into a specific memory location, then
generally the setup_data address parameter is read first, so that the
caller knows where to read it into. In that case, we should return
setup_data containing the absolute addresses that are hard coded and
determined a priori. This is the case when kernels are loaded by BIOS,
for example. In contrast, when setup_data is read as a file, then we
shouldn't modify setup_data, since the absolute address will be wrong by
definition. This is the case when OVMF loads the image.
This allows setup_data to be used like normal, without crashing when EFI
tries to use it.
(As a small development note, strangely, fw_cfg_add_file_callback() was
exported but fw_cfg_add_bytes_callback() wasn't, so this makes that
consistent.)
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Laurent Vivier <laurent@vivier.eu>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: Richard Henderson <richard.henderson@linaro.org>
Suggested-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Message-Id: <20220921093134.2936487-1-Jason@zx2c4.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It was returned as error before. Instead of it, simply update the
corresponding field so qemu can send it in the migration data.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Si-Wei Liu <si-wei.liu@oracle.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Like commit 034d00d485 ("e1000: set RX descriptor status in
a separate operation"), there is also same issue in e1000e, which
would cause lost packets or stop sending packets to VM with DPDK.
Do similar fix in e1000e.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/402
Signed-off-by: Ding Hui <dinghui@sangfor.com.cn>
Signed-off-by: Jason Wang <jasowang@redhat.com>
