Use a common helper with PACK ASCII as the differences are limited to
the stride of the source operand.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Message-Id: <20170531220129.27724-25-aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
For that we need to make program_interrupt available to qemu-user.
Fortunately there is almost nothing to change as both kvm_enabled and
CONFIG_KVM evaluate to false in that case.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Message-Id: <20170531220129.27724-22-aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
As MVCL and MVCLE only differ by their operands, use a common
do_mvcl helper. Optimize it calling fast_memmove and fast_memset.
Correctly write back addresses. Check that r1 and r2/r3 registers
are even.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Message-Id: <20170531220129.27724-21-aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
As CLCL and CLCLE mostly differ by their operands, use a common do_clcl
helper. Another difference is that CLCL is not interruptible.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Message-Id: <20170531220129.27724-19-aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
There are multiple issues with the COMPARE LOGICAL LONG EXTENDED
instruction:
- The test between the two operands is inverted, leading to an inversion
of the cc values 1 and 2.
- The address and length of an operand continue to be decreased after
reaching the end of this operand. These values are then wrong write
back to the registers.
- We should limit the amount of bytes to process, so that interrupts can
be served correctly.
At the same time rename dest into src1 and src into src3 to match the
operand names and make the code less confusing.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Message-Id: <20170531220129.27724-18-aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
These functions differ from COMPARE by generating an exception for a
QNaN input. Use the non quiet version of floatXX_compare.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Message-Id: <20170531220129.27724-10-aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
And at the same time make IPTE SMP aware.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Message-Id: <20170531220129.27724-4-aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Previously, helper_ex would construct the insn and then implement
the insn via direct calls other helpers. This was sufficient to
boot Linux but that is all.
It is easy enough to go the whole nine yards by stashing state for
EXECUTE within the cpu, and then rely on a new TB to be created
that properly and completely interprets the insn.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
This split will be required for implementing EXECUTE properly.
Do this now as a separate step to aid comparison of before and
after TB listings.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Use this saved value instead of recomputing from next_pc difference.
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Also provide the cross-cpu tlb flushing required by the PoO.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The PoO specifies that when R1==0, no ORing into the insn
loaded from storage takes place. Load a zero for this case.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
(1) The OR of the low bits or R1 into INSN were not being done
consistently; it was forgotten along all but the SVC path.
(2) The setting of ILEN was wrong on SVC path for EXRL.
(3) The data load for ICM read too much.
Fix these by consolidating data load at the beginning, using
get_ilen to control the number of bytes loaded, and ORing in
the byte from R1. Use extract64 from the full aligned insn
to extract arguments.
Pass in ILEN rather than RET as the more natural way to give
the required data along the SVC path.
Modify ENV->CC_OP directly rather than include it in the
functional interface.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Fix saving exception_index around mmu_translate; eliminate a dead store.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
